Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>master
parent
75bc8e85b5
commit
7168da1638
@ -0,0 +1,85 @@ |
|||||||
|
U-Boot for UniPhier SoC family |
||||||
|
============================== |
||||||
|
|
||||||
|
|
||||||
|
Tested toolchains |
||||||
|
----------------- |
||||||
|
|
||||||
|
(a) Ubuntu packages (CROSS_COMPILE=arm-linux-gnueabi-) |
||||||
|
|
||||||
|
If you are building U-Boot on Ubuntu, its standard package is recommended. |
||||||
|
You can install it as follows: |
||||||
|
|
||||||
|
$ sudo apt-get install gcc-arm-linux-gnueabi- |
||||||
|
|
||||||
|
(b) Linaro compilers (CROSS_COMPILE=arm-linux-gnueabihf-) |
||||||
|
|
||||||
|
You can download pre-built toolchains from: |
||||||
|
|
||||||
|
http://www.linaro.org/downloads/ |
||||||
|
|
||||||
|
(c) kernel.org compilers (CROSS_COMPILE=arm-unknown-linux-gnueabi-) |
||||||
|
|
||||||
|
You can download pre-built toolchains from: |
||||||
|
|
||||||
|
ftp://www.kernel.org/pub/tools/crosstool/files/bin/ |
||||||
|
|
||||||
|
|
||||||
|
Compile the source |
||||||
|
------------------ |
||||||
|
|
||||||
|
PH1-Pro4: |
||||||
|
$ make ph1_pro4_defconfig |
||||||
|
$ make CROSS_COMPILE=arm-linux-gnueabi- |
||||||
|
|
||||||
|
PH1-LD4: |
||||||
|
$ make ph1_ld4_defconfig |
||||||
|
$ make CROSS_COMPILE=arm-linux-gnueabi- |
||||||
|
|
||||||
|
PH1-sLD8: |
||||||
|
$ make ph1_sld8_defconfig |
||||||
|
$ make CROSS_COMPILE=arm-linux-gnueabi- |
||||||
|
|
||||||
|
You may wish to change the "CROSS_COMPILE=arm-linux-gnueabi-" |
||||||
|
to use your favorite compiler. |
||||||
|
|
||||||
|
|
||||||
|
Burn U-Boot images to NAND |
||||||
|
-------------------------- |
||||||
|
|
||||||
|
Write two files to the NAND device as follows: |
||||||
|
- spl/u-boot-spl.bin at the offset address 0x00000000 |
||||||
|
- u-boot-dtb.img at the offset address 0x00010000 |
||||||
|
|
||||||
|
If a TFTP server is available, the images can be easily updated. |
||||||
|
Just copy the u-boot-spl.bin and u-boot-dtb.img to the TFTP public directory, |
||||||
|
and then run the following command at the U-Boot command line: |
||||||
|
|
||||||
|
=> run nandupdate |
||||||
|
|
||||||
|
|
||||||
|
UniPhier specific commands |
||||||
|
-------------------------- |
||||||
|
|
||||||
|
- pinmon (enabled by CONFIG_CMD_PINMON) |
||||||
|
shows the boot mode pins that has been latched at the power-on reset |
||||||
|
|
||||||
|
- ddrphy (enabled by CONFIG_CMD_DDRPHY_DUMP) |
||||||
|
shows the DDR PHY parameters set by the PHY training |
||||||
|
|
||||||
|
|
||||||
|
Supported devices |
||||||
|
----------------- |
||||||
|
|
||||||
|
- UART (on-chip) |
||||||
|
- NAND |
||||||
|
- USB (2.0) |
||||||
|
- LAN (on-board SMSC9118) |
||||||
|
- I2C |
||||||
|
- EEPROM (connected to the on-board I2C bus) |
||||||
|
- Support card (SRAM, NOR flash, some peripherals) |
||||||
|
|
||||||
|
|
||||||
|
-- |
||||||
|
Masahiro Yamada <yamada.m@jp.panasonic.com> |
||||||
|
Feb. 2015 |
Loading…
Reference in new issue