ppc4xx: Add support for GPCS, SGMII and M88E1112 PHY

This patch adds GPCS, SGMII and M88E1112 PHY support
for the AMCC PPC460GT/EX processors.

Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
master
Victor Gallardo 17 years ago committed by Stefan Roese
parent f6b6c45840
commit 78d7823689
  1. 159
      cpu/ppc4xx/4xx_enet.c
  2. 41
      cpu/ppc4xx/miiphy.c
  3. 3
      include/ppc4xx_enet.h

@ -198,6 +198,7 @@
#define BI_PHYMODE_RMII 8
#endif
#endif
#define BI_PHYMODE_SGMII 9
#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
@ -216,6 +217,52 @@
#define MAL_RX_CHAN_MUL 1
#endif
/*--------------------------------------------------------------------+
* Fixed PHY (PHY-less) support for Ethernet Ports.
*--------------------------------------------------------------------*/
/*
* Some boards do not have a PHY for each ethernet port. These ports
* are known as Fixed PHY (or PHY-less) ports. For such ports, set
* the appropriate CONFIG_PHY_ADDR equal to CONFIG_FIXED_PHY and
* then define CFG_FIXED_PHY_PORTS to define what the speed and
* duplex should be for these ports in the board configuration
* file.
*
* For Example:
* #define CONFIG_FIXED_PHY 0xFFFFFFFF
*
* #define CONFIG_PHY_ADDR CONFIG_FIXED_PHY
* #define CONFIG_PHY1_ADDR 1
* #define CONFIG_PHY2_ADDR CONFIG_FIXED_PHY
* #define CONFIG_PHY3_ADDR 3
*
* #define CFG_FIXED_PHY_PORT(devnum,speed,duplex) \
* {devnum, speed, duplex},
*
* #define CFG_FIXED_PHY_PORTS \
* CFG_FIXED_PHY_PORT(0,1000,FULL) \
* CFG_FIXED_PHY_PORT(2,100,HALF)
*/
#ifndef CONFIG_FIXED_PHY
#define CONFIG_FIXED_PHY 0xFFFFFFFF /* Fixed PHY (PHY-less) */
#endif
#ifndef CFG_FIXED_PHY_PORTS
#define CFG_FIXED_PHY_PORTS /* default is an empty array */
#endif
struct fixed_phy_port {
unsigned int devnum; /* ethernet port */
unsigned int speed; /* specified speed 10,100 or 1000 */
unsigned int duplex; /* specified duplex FULL or HALF */
};
static const struct fixed_phy_port fixed_phy_port[] = {
CFG_FIXED_PHY_PORTS /* defined in board configuration file */
};
/*-----------------------------------------------------------------------------+
* Global variables. TX and RX descriptors and buffers.
*-----------------------------------------------------------------------------*/
@ -611,8 +658,17 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
#if defined(CONFIG_460EX)
mode = 9;
mfsdr(SDR0_ETH_CFG, eth_cfg);
if (((eth_cfg & SDR0_ETH_CFG_SGMII0_ENABLE) > 0) &&
((eth_cfg & SDR0_ETH_CFG_SGMII1_ENABLE) > 0))
mode = 11; /* config SGMII */
#else
mode = 10;
mfsdr(SDR0_ETH_CFG, eth_cfg);
if (((eth_cfg & SDR0_ETH_CFG_SGMII0_ENABLE) > 0) &&
((eth_cfg & SDR0_ETH_CFG_SGMII1_ENABLE) > 0) &&
((eth_cfg & SDR0_ETH_CFG_SGMII2_ENABLE) > 0))
mode = 12; /* config SGMII */
#endif
/* TODO:
@ -635,6 +691,8 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
/*
* Right now only 2*RGMII is supported. Please extend when needed.
* sr - 2008-02-19
* Add SGMII support.
* vg - 2008-07-28
*/
switch (mode) {
case 1:
@ -761,6 +819,20 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
bis->bi_phymode[2] = BI_PHYMODE_RGMII;
bis->bi_phymode[3] = BI_PHYMODE_RGMII;
break;
case 11:
/* 2 SGMII - 460EX */
bis->bi_phymode[0] = BI_PHYMODE_SGMII;
bis->bi_phymode[1] = BI_PHYMODE_SGMII;
bis->bi_phymode[2] = BI_PHYMODE_NONE;
bis->bi_phymode[3] = BI_PHYMODE_NONE;
break;
case 12:
/* 3 SGMII - 460GT */
bis->bi_phymode[0] = BI_PHYMODE_SGMII;
bis->bi_phymode[1] = BI_PHYMODE_SGMII;
bis->bi_phymode[2] = BI_PHYMODE_SGMII;
bis->bi_phymode[3] = BI_PHYMODE_NONE;
break;
default:
break;
}
@ -945,6 +1017,48 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
out_be32((void *)EMAC_M1 + hw_p->hw_addr, mode_reg);
#endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */
#if defined(CONFIG_GPCS_PHY_ADDR) || defined(CONFIG_GPCS_PHY1_ADDR) || \
defined(CONFIG_GPCS_PHY2_ADDR) || defined(CONFIG_GPCS_PHY3_ADDR)
if (bis->bi_phymode[devnum] == BI_PHYMODE_SGMII) {
/*
* In SGMII mode, GPCS access is needed for
* communication with the internal SGMII SerDes.
*/
switch (devnum) {
#if defined(CONFIG_GPCS_PHY_ADDR)
case 0:
reg = CONFIG_GPCS_PHY_ADDR;
break;
#endif
#if defined(CONFIG_GPCS_PHY1_ADDR)
case 1:
reg = CONFIG_GPCS_PHY1_ADDR;
break;
#endif
#if defined(CONFIG_GPCS_PHY2_ADDR)
case 2:
reg = CONFIG_GPCS_PHY2_ADDR;
break;
#endif
#if defined(CONFIG_GPCS_PHY3_ADDR)
case 3:
reg = CONFIG_GPCS_PHY3_ADDR;
break;
#endif
}
mode_reg = in_be32((void *)EMAC_M1 + hw_p->hw_addr);
mode_reg |= EMAC_M1_MF_1000GPCS | EMAC_M1_IPPA_SET(reg);
out_be32((void *)EMAC_M1 + hw_p->hw_addr, mode_reg);
/* Configure GPCS interface to recommended setting for SGMII */
miiphy_reset(dev->name, reg);
miiphy_write(dev->name, reg, 0x04, 0x8120); /* AsymPause, FDX */
miiphy_write(dev->name, reg, 0x07, 0x2801); /* msg_pg, toggle */
miiphy_write(dev->name, reg, 0x00, 0x0140); /* 1Gbps, FDX */
}
#endif /* defined(CONFIG_GPCS_PHY_ADDR) */
/* wait for PHY to complete auto negotiation */
reg_short = 0;
#ifndef CONFIG_CS8952_PHY
@ -974,6 +1088,9 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
bis->bi_phynum[devnum] = reg;
if (reg == CONFIG_FIXED_PHY)
goto get_speed;
#if defined(CONFIG_PHY_RESET)
/*
* Reset the phy, only if its the first time through
@ -986,6 +1103,27 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
miiphy_write (dev->name, reg, 0x09, 0x0e00);
miiphy_write (dev->name, reg, 0x04, 0x01e1);
#endif
#if defined(CONFIG_M88E1112_PHY)
if (bis->bi_phymode[devnum] == BI_PHYMODE_SGMII) {
/*
* Marvell 88E1112 PHY needs to have the SGMII MAC
* interace (page 2) properly configured to
* communicate with the 460EX/GT GPCS interface.
*/
/* Set access to Page 2 */
miiphy_write(dev->name, reg, 0x16, 0x0002);
miiphy_write(dev->name, reg, 0x00, 0x0040); /* 1Gbps */
miiphy_read(dev->name, reg, 0x1a, &reg_short);
reg_short |= 0x8000; /* bypass Auto-Negotiation */
miiphy_write(dev->name, reg, 0x1a, reg_short);
miiphy_reset(dev->name, reg); /* reset MAC interface */
/* Reset access to Page 0 */
miiphy_write(dev->name, reg, 0x16, 0x0000);
}
#endif /* defined(CONFIG_M88E1112_PHY) */
miiphy_reset (dev->name, reg);
#if defined(CONFIG_440GX) || \
@ -1080,8 +1218,25 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
}
#endif /* #ifndef CONFIG_CS8952_PHY */
speed = miiphy_speed (dev->name, reg);
duplex = miiphy_duplex (dev->name, reg);
get_speed:
if (reg == CONFIG_FIXED_PHY) {
for (i = 0; i < ARRAY_SIZE(fixed_phy_port); i++) {
if (devnum == fixed_phy_port[i].devnum) {
speed = fixed_phy_port[i].speed;
duplex = fixed_phy_port[i].duplex;
break;
}
}
if (i == ARRAY_SIZE(fixed_phy_port)) {
printf("ERROR: PHY (%s) not configured correctly!\n",
dev->name);
return -1;
}
} else {
speed = miiphy_speed(dev->name, reg);
duplex = miiphy_duplex(dev->name, reg);
}
if (hw_p->print_speed) {
hw_p->print_speed = 0;

@ -180,8 +180,10 @@ int phy_setup_aneg (char *devname, unsigned char addr)
*
* sr: Currently on 460EX only EMAC0 works with MDIO, so we always
* return EMAC0 offset here
* vg: For 460EX/460GT if internal GPCS PHY address is specified
* return appropriate EMAC offset
*/
unsigned int miiphy_getemac_offset (void)
unsigned int miiphy_getemac_offset(u8 addr)
{
#if (defined(CONFIG_440) && \
!defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \
@ -233,6 +235,39 @@ unsigned int miiphy_getemac_offset (void)
return 0x100;
#endif
#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
u32 mode_reg;
u32 eoffset = 0;
switch (addr) {
#if defined(CONFIG_HAS_ETH1) && defined(CONFIG_GPCS_PHY1_ADDR)
case CONFIG_GPCS_PHY1_ADDR:
mode_reg = in_be32((void *)EMAC_M1 + 0x100);
if (addr == EMAC_M1_IPPA_GET(mode_reg))
eoffset = 0x100;
break;
#endif
#if defined(CONFIG_HAS_ETH2) && defined(CONFIG_GPCS_PHY2_ADDR)
case CONFIG_GPCS_PHY2_ADDR:
mode_reg = in_be32((void *)EMAC_M1 + 0x300);
if (addr == EMAC_M1_IPPA_GET(mode_reg))
eoffset = 0x300;
break;
#endif
#if defined(CONFIG_HAS_ETH3) && defined(CONFIG_GPCS_PHY3_ADDR)
case CONFIG_GPCS_PHY3_ADDR:
mode_reg = in_be32((void *)EMAC_M1 + 0x400);
if (addr == EMAC_M1_IPPA_GET(mode_reg))
eoffset = 0x400;
break;
#endif
default:
eoffset = 0;
break;
}
return eoffset;
#endif
return 0;
#endif
}
@ -262,7 +297,7 @@ static int emac_miiphy_command(u8 addr, u8 reg, int cmd, u16 value)
u32 emac_reg;
u32 sta_reg;
emac_reg = miiphy_getemac_offset();
emac_reg = miiphy_getemac_offset(addr);
/* wait for completion */
if (emac_miiphy_wait(emac_reg) != 0)
@ -311,7 +346,7 @@ int emac4xx_miiphy_read (char *devname, unsigned char addr, unsigned char reg,
unsigned long sta_reg;
unsigned long emac_reg;
emac_reg = miiphy_getemac_offset ();
emac_reg = miiphy_getemac_offset(addr);
if (emac_miiphy_command(addr, reg, EMAC_STACR_READ, 0) != 0)
return -1;

@ -376,6 +376,7 @@ typedef struct emac_4xx_hw_st {
#define EMAC_M1_APP (0x08000000)
#define EMAC_M1_RSVD (0x06000000)
#define EMAC_M1_IST (0x01000000)
#define EMAC_M1_MF_1000GPCS (0x00C00000)
#define EMAC_M1_MF_1000MBPS (0x00800000) /* 0's for 10MBPS */
#define EMAC_M1_MF_100MBPS (0x00400000)
#define EMAC_M1_RFS_MASK (0x00380000)
@ -394,6 +395,8 @@ typedef struct emac_4xx_hw_st {
#define EMAC_M1_MWSW (0x00007000)
#define EMAC_M1_JUMBO_ENABLE (0x00000800)
#define EMAC_M1_IPPA (0x000007c0)
#define EMAC_M1_IPPA_SET(id) (((id) & 0x1f) << 6)
#define EMAC_M1_IPPA_GET(id) (((id) >> 6) & 0x1f)
#define EMAC_M1_OBCI_GT100 (0x00000020)
#define EMAC_M1_OBCI_100 (0x00000018)
#define EMAC_M1_OBCI_83 (0x00000010)

Loading…
Cancel
Save