This is a virtual "board" that uses configuration files and Kconfig to define the memory layout used by a real board during the board bring-up process. It generates an SPL image that can be loaded using imx_usb or SB_LOADER.exe. When run, it will generate a set of calibration constants for use in either or both a DCD configuration file for boards that use u-boot.imx or struct mx6_mmdc_calibration for boards that boot via SPL. In essence, it is a configurable, open-source variant of the Freescale ddr-stress tool. https://community.nxp.com/docs/DOC-105652 File mx6memcal_defconfig configures the board for use with mx6sabresd or mx6qsabreauto. Signed-off-by: Eric Nelson <eric@nelint.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>master
parent
1314bd1192
commit
baefb63a13
@ -0,0 +1,235 @@ |
|||||||
|
if TARGET_MX6MEMCAL |
||||||
|
|
||||||
|
config SYS_BOARD |
||||||
|
default "mx6memcal" |
||||||
|
|
||||||
|
config SYS_VENDOR |
||||||
|
default "freescale" |
||||||
|
|
||||||
|
config SYS_CONFIG_NAME |
||||||
|
default "mx6memcal" |
||||||
|
|
||||||
|
menu "mx6memcal specifics" |
||||||
|
choice |
||||||
|
prompt "Serial console" |
||||||
|
help |
||||||
|
Either UART1 or UART2 will be used as the console for |
||||||
|
displaying the calibration values or errors. |
||||||
|
|
||||||
|
config SERIAL_CONSOLE_UART1 |
||||||
|
bool "UART1" |
||||||
|
help |
||||||
|
Select this if your board uses UART1 for its' console. |
||||||
|
|
||||||
|
config SERIAL_CONSOLE_UART2 |
||||||
|
bool "UART2" |
||||||
|
help |
||||||
|
Select this if your board uses UART2 for its' console. |
||||||
|
|
||||||
|
endchoice |
||||||
|
|
||||||
|
choice |
||||||
|
prompt "UART pads" |
||||||
|
help |
||||||
|
Select the RX and TX pads used for your serial console. |
||||||
|
The choices below reflect the most commonly used options |
||||||
|
for your UART. |
||||||
|
|
||||||
|
config UART2_EIM_D26_27 |
||||||
|
bool "UART2 on EIM_D26/27 (SabreLite, Nitrogen6x)" |
||||||
|
depends on SERIAL_CONSOLE_UART2 |
||||||
|
help |
||||||
|
Choose this configuration if you're using pads |
||||||
|
EIM_D26 and D27 for a console on UART2. |
||||||
|
This is typical for designs that are based on the |
||||||
|
NXP SABRELite. |
||||||
|
|
||||||
|
config UART1_CSI0_DAT10_11 |
||||||
|
bool "UART1 on CSI0_DAT10/11 (Wand)" |
||||||
|
depends on SERIAL_CONSOLE_UART1 |
||||||
|
help |
||||||
|
Choose this configuration if you're using pads |
||||||
|
CSI0_DAT10 and DAT11 for a console on UART1 as |
||||||
|
is done on the i.MX6 Wand board. |
||||||
|
|
||||||
|
config UART1_SD3_DAT6_7 |
||||||
|
bool "UART1 on SD3_DAT6/7 (SabreSD, SabreAuto)" |
||||||
|
depends on SERIAL_CONSOLE_UART1 |
||||||
|
help |
||||||
|
Choose this configuration if you're using pads |
||||||
|
SD3_DAT6 and DAT7 for a console on UART1 as is |
||||||
|
done on the NXP SABRESD or SABREAUTO designs. |
||||||
|
|
||||||
|
config UART1_UART1 |
||||||
|
bool "UART1 on UART1 (i.MX6SL EVK, WaRP)" |
||||||
|
depends on SERIAL_CONSOLE_UART1 |
||||||
|
help |
||||||
|
Choose this configuration if you're using pads |
||||||
|
UART1_TXD/RXD for a console on UART1 as is done |
||||||
|
on most i.MX6SL designs. |
||||||
|
|
||||||
|
endchoice |
||||||
|
|
||||||
|
config IMXIMAGE_OUTPUT |
||||||
|
bool "Include output for imximage .cfg files" |
||||||
|
default y |
||||||
|
help |
||||||
|
Say "Y" if you want output formatted for use in non-SPL |
||||||
|
(DCD-style) configuration files. |
||||||
|
|
||||||
|
config DDRWIDTH |
||||||
|
int "DDR bus width" |
||||||
|
default 64 |
||||||
|
help |
||||||
|
Select either 32 or 64 to reflect the DDR bus width. |
||||||
|
|
||||||
|
config DDRCS |
||||||
|
int "DDR chip selects" |
||||||
|
default 2 |
||||||
|
range 1 2 |
||||||
|
help |
||||||
|
Select the number of chip selects used in your board design |
||||||
|
|
||||||
|
choice |
||||||
|
prompt "Memory type" |
||||||
|
help |
||||||
|
Select the type of DDR (DDR3 or LPDDR2) used on your design |
||||||
|
|
||||||
|
config DDR3 |
||||||
|
bool "DDR3" |
||||||
|
help |
||||||
|
Select this if your board design uses DDR3. |
||||||
|
|
||||||
|
config LPDDR2 |
||||||
|
bool "LPDDR2" |
||||||
|
help |
||||||
|
Select this if your board design uses LPDDR2. |
||||||
|
|
||||||
|
endchoice |
||||||
|
|
||||||
|
choice |
||||||
|
prompt "Memory device" |
||||||
|
|
||||||
|
config MT41K512M16TNA |
||||||
|
bool "Micron MT41K512M16TNA 512Mx16 (1GiB/chip)" |
||||||
|
depends on DDR3 |
||||||
|
|
||||||
|
config MT41K128M16JT |
||||||
|
bool "Micron MT41K128M16JT 128Mx16 (256 MiB/chip)" |
||||||
|
depends on DDR3 |
||||||
|
|
||||||
|
config H5TQ4G63AFR |
||||||
|
bool "Hynix H5TQ4G63AFR 256Mx16 (512 MiB/chip)" |
||||||
|
depends on DDR3 |
||||||
|
|
||||||
|
config H5TQ2G63DFR |
||||||
|
bool "Hynix H5TQ2G63DFR 128Mx16 (256 MiB/chip)" |
||||||
|
depends on DDR3 |
||||||
|
|
||||||
|
config MT42L256M32D2LG |
||||||
|
bool "Micron MT42L256M32D2LG LPDDR2 256Mx32 (1GiB/chip)" |
||||||
|
depends on LPDDR2 |
||||||
|
|
||||||
|
config MT29PZZZ4D4BKESK |
||||||
|
bool "Micron MT29PZZZ4D4BKESK multi-chip 512MiB LPDDR2/4GiB eMMC" |
||||||
|
depends on LPDDR2 |
||||||
|
|
||||||
|
endchoice |
||||||
|
|
||||||
|
config DDR_ODT |
||||||
|
int "DDR On-die-termination" |
||||||
|
default 2 |
||||||
|
range 0 7 |
||||||
|
help |
||||||
|
Enter the on-die termination value as an index defined for |
||||||
|
IOMUX settings for PAD_DRAM_SDCLK0_P and others. |
||||||
|
0 == Disabled |
||||||
|
1 == 120 Ohm |
||||||
|
2 == 60 Ohm |
||||||
|
3 == 40 Ohm |
||||||
|
4 == 30 Ohm |
||||||
|
5 == 24 Ohm |
||||||
|
6 == 20 Ohm |
||||||
|
7 == 17 Ohm |
||||||
|
Value will be applied to all clock and data lines |
||||||
|
|
||||||
|
|
||||||
|
config DRAM_DRIVE_STRENGTH |
||||||
|
int "DRAM Drive strength" |
||||||
|
default 6 |
||||||
|
range 0 7 |
||||||
|
help |
||||||
|
Enter drive strength as an index defined for IOMUX settings |
||||||
|
for GRP_B1DS and others. |
||||||
|
0 == Hi Z |
||||||
|
6 == 40 Ohm (default) |
||||||
|
7 == 34 Ohm |
||||||
|
Value will be applied to all clock and data lines |
||||||
|
|
||||||
|
config RTT_NOM |
||||||
|
int "RTT_NOM" |
||||||
|
default 1 |
||||||
|
range 1 2 |
||||||
|
help |
||||||
|
Enter the RTT_NOM selector |
||||||
|
1 == RZQ/4 (60ohm) |
||||||
|
2 == RZQ/2 (120ohm) |
||||||
|
|
||||||
|
config RTT_WR |
||||||
|
int "RTT_WR" |
||||||
|
default 1 |
||||||
|
range 0 2 |
||||||
|
help |
||||||
|
Enter the RTT_WR selector for MR2 |
||||||
|
0 == Dynamic ODT disabled |
||||||
|
1 == RZQ/4 (60ohm) |
||||||
|
2 == RZQ/2 (120ohm) |
||||||
|
|
||||||
|
config RALAT |
||||||
|
int "Read additional latency" |
||||||
|
default 5 |
||||||
|
range 0 7 |
||||||
|
help |
||||||
|
Enter a latency in number of cycles. This will be added to |
||||||
|
CAS and internal delays for which the MMDC will retrieve the |
||||||
|
read data from the internal FIFO. |
||||||
|
This is used to compensate for board/chip delays. |
||||||
|
|
||||||
|
config WALAT |
||||||
|
int "Write additional latency" |
||||||
|
default 0 |
||||||
|
range 0 7 |
||||||
|
help |
||||||
|
Enter a latency in number of cycles. This will be added to |
||||||
|
CAS and internal delays for which the MMDC will retrieve the |
||||||
|
read data from the internal FIFO |
||||||
|
This is used to compensate for board/chip delays. |
||||||
|
|
||||||
|
config REFSEL |
||||||
|
int "Refresh period" |
||||||
|
range 0 3 |
||||||
|
default 1 |
||||||
|
help |
||||||
|
Select the DDR refresh period. |
||||||
|
See the description of bitfield REF_SEL in the reference manual |
||||||
|
for details. |
||||||
|
0 == disabled |
||||||
|
1 == 32 kHz |
||||||
|
2 == 64 kHz |
||||||
|
3 == fast counter |
||||||
|
|
||||||
|
config REFR |
||||||
|
int "Number of refreshes" |
||||||
|
range 0 7 |
||||||
|
default 7 |
||||||
|
help |
||||||
|
This selects the number of refreshes (-1) during each period. |
||||||
|
i.e.: |
||||||
|
0 == 1 refresh (tRFC) |
||||||
|
7 == 8 refreshes (tRFC*8) |
||||||
|
See the description of MDREF[REFR] in the reference manual for |
||||||
|
details. |
||||||
|
|
||||||
|
endmenu |
||||||
|
endif |
||||||
|
|
@ -0,0 +1,7 @@ |
|||||||
|
MX6MEMCAL BOARD |
||||||
|
M: Eric Nelson <eric@nelint.com> |
||||||
|
S: Maintained |
||||||
|
F: board/freescale/mx6memcal/ |
||||||
|
F: include/configs/mx6memcal.h |
||||||
|
F: configs/mx6memcal_defconfig |
||||||
|
|
@ -0,0 +1,13 @@ |
|||||||
|
#
|
||||||
|
# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
|
||||||
|
#
|
||||||
|
# (C) Copyright 2011 Freescale Semiconductor, Inc.
|
||||||
|
#
|
||||||
|
# SPDX-License-Identifier: GPL-2.0+
|
||||||
|
#
|
||||||
|
|
||||||
|
ifdef CONFIG_SPL_BUILD |
||||||
|
obj-y := spl.o
|
||||||
|
else |
||||||
|
obj-y := mx6memcal.o
|
||||||
|
endif |
@ -0,0 +1,49 @@ |
|||||||
|
mx6memcal - a tool for calibrating DDR on i.MX6 boards. |
||||||
|
|
||||||
|
The mx6memcal board isn't a real board, but a tool for use in bring-up of |
||||||
|
new i.MX6 board designs. |
||||||
|
|
||||||
|
It provides a similar function to the tool from NXP([1]) with a number |
||||||
|
of advantages: |
||||||
|
|
||||||
|
1. It's open-source, so it's easier to change if needed. |
||||||
|
Typical reasons for needing to change include the use of alternate |
||||||
|
UARTs and PMIC initialization. |
||||||
|
2. It produces an image that's directly loadable with imx_usb [2] or |
||||||
|
SB_LOADER.exe [3]. |
||||||
|
The NXP tool requires either a cumbersome JTAG connection that |
||||||
|
makes running the DDR very slow or a working U-Boot image that |
||||||
|
suffers from a chicken-and-egg problem (i.e. where do you get the |
||||||
|
DDR parameters for U-Boot?). |
||||||
|
3. It doesn't prompt for parameters, so it's much faster to gather |
||||||
|
data from multiple boards. |
||||||
|
4. Parameters to the calibration process can be chosen through |
||||||
|
'make menuconfig'. |
||||||
|
|
||||||
|
When booted, the mx6memcal board will run the DDR calibration |
||||||
|
routines and display the result in a form suitable for cut and |
||||||
|
paste into struct mx6_mmdc_calibration. It can also optionally |
||||||
|
produce output in a form usable in a DCD-style .cfg file. |
||||||
|
|
||||||
|
Selections in Kconfig allow most system design settings to be chosen: |
||||||
|
|
||||||
|
1. The UART number and pad configuration for the UART. Options |
||||||
|
include support for the most frequent reference designs on |
||||||
|
i.MX6DQ/SDL (SABRE Lite and SABRESD designs). |
||||||
|
2. The memory bus width (64 and 32-bit) |
||||||
|
3. The number of chip-selects in use |
||||||
|
4. The type of DDR (DDR3 or LPDDR2). Note that LPDDR2 support |
||||||
|
is incomplete as of this writing. |
||||||
|
5. The type of DDR chips in use. This selection allows re-use of common |
||||||
|
parts and four DDR3 and two LPDDR2 parts are currently defined |
||||||
|
6. The On-die termination value for the DRAM lines |
||||||
|
7. The DRAM drive strength |
||||||
|
8. The RTT_NOM and RTT_WR termination settings |
||||||
|
9. RALAT/WALAT latency values |
||||||
|
|
||||||
|
References: |
||||||
|
[1] - NXP DDR Stress Test Tool - https://community.nxp.com/docs/DOC-105652 |
||||||
|
[2] - Boundary Devices imx_usb_loader |
||||||
|
https://github.com/boundarydevices/imx_usb_loader |
||||||
|
[3] - Use of SB_Loader.exe |
||||||
|
https://boundarydevices.com/windows-users-and-unbricking |
@ -0,0 +1,32 @@ |
|||||||
|
/*
|
||||||
|
* mx6memcal board support - provides a minimal, UART-only |
||||||
|
* U-Boot that's capable of running a memory test. |
||||||
|
* |
||||||
|
* Copyright (C) 2016 Nelson Integration, LLC |
||||||
|
* Author: Eric Nelson <eric@nelint.com> |
||||||
|
* |
||||||
|
* SPDX-License-Identifier: GPL-2.0+ |
||||||
|
*/ |
||||||
|
|
||||||
|
#include <common.h> |
||||||
|
#include <asm/arch/sys_proto.h> |
||||||
|
|
||||||
|
DECLARE_GLOBAL_DATA_PTR; |
||||||
|
|
||||||
|
int board_init(void) |
||||||
|
{ |
||||||
|
return 0; |
||||||
|
} |
||||||
|
|
||||||
|
int checkboard(void) |
||||||
|
{ |
||||||
|
puts("Board: mx6memcal\n"); |
||||||
|
return 0; |
||||||
|
} |
||||||
|
|
||||||
|
int dram_init(void) |
||||||
|
{ |
||||||
|
gd->ram_size = imx_ddr_size(); |
||||||
|
return 0; |
||||||
|
} |
||||||
|
|
@ -0,0 +1,456 @@ |
|||||||
|
/*
|
||||||
|
* Copyright (C) 2016 Nelson Integration, LLC |
||||||
|
* Author: Eric Nelson <eric@nelint.com> |
||||||
|
* |
||||||
|
* SPDX-License-Identifier: GPL-2.0+ |
||||||
|
*/ |
||||||
|
|
||||||
|
#include <common.h> |
||||||
|
#include <asm/io.h> |
||||||
|
#include <asm/arch/iomux.h> |
||||||
|
#include <asm/arch/clock.h> |
||||||
|
#include <asm/arch/crm_regs.h> |
||||||
|
#include <asm/arch/mx6-ddr.h> |
||||||
|
#include <asm/arch/mx6-pins.h> |
||||||
|
#include <asm/arch/sys_proto.h> |
||||||
|
#include <spl.h> |
||||||
|
|
||||||
|
DECLARE_GLOBAL_DATA_PTR; |
||||||
|
|
||||||
|
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ |
||||||
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
|
||||||
|
PAD_CTL_SRE_FAST | PAD_CTL_HYS) |
||||||
|
|
||||||
|
static iomux_v3_cfg_t const uart_pads[] = { |
||||||
|
#ifdef CONFIG_UART2_EIM_D26_27 |
||||||
|
IOMUX_PADS(PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
||||||
|
IOMUX_PADS(PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
||||||
|
#elif defined(CONFIG_UART1_CSI0_DAT10_11) |
||||||
|
IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
||||||
|
IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
||||||
|
#elif defined(CONFIG_UART1_SD3_DAT6_7) |
||||||
|
IOMUX_PADS(PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
||||||
|
IOMUX_PADS(PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
||||||
|
#elif defined(CONFIG_UART1_UART1) |
||||||
|
MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL), |
||||||
|
MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL), |
||||||
|
#else |
||||||
|
#error select UART console pads |
||||||
|
#endif |
||||||
|
}; |
||||||
|
|
||||||
|
#ifdef CONFIG_DDR3 |
||||||
|
#define GRP_DDRTYPE 0x000C0000 |
||||||
|
#else |
||||||
|
#define GRP_DDRTYPE 0x00080000 |
||||||
|
#endif |
||||||
|
|
||||||
|
/* all existing designs have this disabled */ |
||||||
|
#define DDR_PKE 0 |
||||||
|
|
||||||
|
/* use Kconfig for ODT and DRIVE_STRENGTH */ |
||||||
|
#define DDR_ODT \ |
||||||
|
(CONFIG_DDR_ODT << 8) |
||||||
|
#define DRAM_DRIVE_STRENGTH \ |
||||||
|
(CONFIG_DRAM_DRIVE_STRENGTH << 3) |
||||||
|
|
||||||
|
/* configure MX6Q/DUAL mmdc DDR io registers */ |
||||||
|
static struct mx6dq_iomux_ddr_regs const mx6dq_ddr_ioregs = { |
||||||
|
/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */ |
||||||
|
.dram_sdclk_0 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdclk_1 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_cas = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_ras = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_reset = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
/* SDCKE[0:1]: 100k pull-up */ |
||||||
|
.dram_sdcke0 = 0x00003000, |
||||||
|
.dram_sdcke1 = 0x00003000, |
||||||
|
/* SDBA2: pull-up disabled */ |
||||||
|
.dram_sdba2 = 0x00000000, |
||||||
|
/* SDODT[0:1]: 100k pull-up, 40 ohm */ |
||||||
|
.dram_sdodt0 = 0x00003000 + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdodt1 = 0x00003000 + DRAM_DRIVE_STRENGTH, |
||||||
|
/* SDQS[0:7]: Differential input, 40 ohm */ |
||||||
|
.dram_sdqs0 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs1 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs2 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs3 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs4 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs5 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs6 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs7 = DRAM_DRIVE_STRENGTH, |
||||||
|
|
||||||
|
/* DQM[0:7]: Differential input, 40 ohm */ |
||||||
|
.dram_dqm0 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm1 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm2 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm3 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm4 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm5 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm6 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm7 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
}; |
||||||
|
|
||||||
|
/* configure MX6Q/DUAL mmdc GRP io registers */ |
||||||
|
static struct mx6dq_iomux_grp_regs const mx6dq_grp_ioregs = { |
||||||
|
/* DDR3 */ |
||||||
|
.grp_ddr_type = GRP_DDRTYPE, |
||||||
|
.grp_ddrmode_ctl = DDR_ODT, |
||||||
|
/* disable DDR pullups */ |
||||||
|
.grp_ddrpke = DDR_PKE, |
||||||
|
/* ADDR[00:16], SDBA[0:1]: 40 ohm */ |
||||||
|
.grp_addds = DRAM_DRIVE_STRENGTH, |
||||||
|
/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */ |
||||||
|
.grp_ctlds = DRAM_DRIVE_STRENGTH, |
||||||
|
/* DATA[00:63]: Differential input, 40 ohm */ |
||||||
|
.grp_ddrmode = DDR_ODT, |
||||||
|
.grp_b0ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b1ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b2ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b3ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b4ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b5ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b6ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b7ds = DRAM_DRIVE_STRENGTH, |
||||||
|
}; |
||||||
|
|
||||||
|
static struct mx6sdl_iomux_ddr_regs const mx6sdl_ddr_ioregs = { |
||||||
|
/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */ |
||||||
|
.dram_sdclk_0 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdclk_1 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_cas = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_ras = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_reset = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
/* SDCKE[0:1]: 100k pull-up */ |
||||||
|
.dram_sdcke0 = 0x00003000, |
||||||
|
.dram_sdcke1 = 0x00003000, |
||||||
|
/* SDBA2: pull-up disabled */ |
||||||
|
.dram_sdba2 = 0x00000000, |
||||||
|
/* SDODT[0:1]: 100k pull-up, 40 ohm */ |
||||||
|
.dram_sdodt0 = 0x00003000 + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdodt1 = 0x00003000 + DRAM_DRIVE_STRENGTH, |
||||||
|
/* SDQS[0:7]: Differential input, 40 ohm */ |
||||||
|
.dram_sdqs0 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs1 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs2 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs3 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs4 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs5 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs6 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs7 = DRAM_DRIVE_STRENGTH, |
||||||
|
|
||||||
|
/* DQM[0:7]: Differential input, 40 ohm */ |
||||||
|
.dram_dqm0 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm1 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm2 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm3 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm4 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm5 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm6 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm7 = DDR_ODT + DRAM_DRIVE_STRENGTH, |
||||||
|
}; |
||||||
|
|
||||||
|
/* configure MX6SOLO/DUALLITE mmdc GRP io registers */ |
||||||
|
static struct mx6sdl_iomux_grp_regs const mx6sdl_grp_ioregs = { |
||||||
|
/* DDR3 */ |
||||||
|
.grp_ddr_type = GRP_DDRTYPE, |
||||||
|
/* SDQS[0:7]: Differential input, 40 ohm */ |
||||||
|
.grp_ddrmode_ctl = DDR_ODT, |
||||||
|
/* disable DDR pullups */ |
||||||
|
.grp_ddrpke = DDR_PKE, |
||||||
|
/* ADDR[00:16], SDBA[0:1]: 40 ohm */ |
||||||
|
.grp_addds = DRAM_DRIVE_STRENGTH, |
||||||
|
/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */ |
||||||
|
.grp_ctlds = DRAM_DRIVE_STRENGTH, |
||||||
|
/* DATA[00:63]: Differential input, 40 ohm */ |
||||||
|
.grp_ddrmode = DDR_ODT, |
||||||
|
.grp_b0ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b1ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b2ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b3ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b4ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b5ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b6ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b7ds = DRAM_DRIVE_STRENGTH, |
||||||
|
}; |
||||||
|
|
||||||
|
const struct mx6sl_iomux_ddr_regs mx6sl_ddr_ioregs = { |
||||||
|
.dram_sdqs0 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs1 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs2 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdqs3 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm0 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm1 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm2 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_dqm3 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_cas = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_ras = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdclk_0 = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_reset = DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_sdba2 = 0x00020000, |
||||||
|
.dram_odt0 = 0x00030000 + DRAM_DRIVE_STRENGTH, |
||||||
|
.dram_odt1 = 0x00030000 + DRAM_DRIVE_STRENGTH, |
||||||
|
}; |
||||||
|
|
||||||
|
const struct mx6sl_iomux_grp_regs mx6sl_grp_ioregs = { |
||||||
|
.grp_b0ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b1ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b2ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_b3ds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_addds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_ctlds = DRAM_DRIVE_STRENGTH, |
||||||
|
.grp_ddrmode_ctl = DDR_ODT, |
||||||
|
.grp_ddrpke = DDR_PKE, |
||||||
|
.grp_ddrmode = DDR_ODT, |
||||||
|
.grp_ddr_type = GRP_DDRTYPE, |
||||||
|
}; |
||||||
|
|
||||||
|
static struct mx6_ddr_sysinfo const sysinfo = { |
||||||
|
/* width of data bus:0=16,1=32,2=64 */ |
||||||
|
#if CONFIG_DDRWIDTH == 32 |
||||||
|
.dsize = 1, |
||||||
|
#elif CONFIG_DDRWIDTH == 64 |
||||||
|
.dsize = 2, |
||||||
|
#else |
||||||
|
#error missing CONFIG_DDRWIDTH |
||||||
|
#endif |
||||||
|
/* config for full 4GB range so that get_mem_size() works */ |
||||||
|
.cs_density = 32, /* 32Gb per CS */ |
||||||
|
|
||||||
|
/* # of chip selects */ |
||||||
|
.ncs = CONFIG_DDRCS, |
||||||
|
.cs1_mirror = 0, |
||||||
|
.bi_on = 1, /* Bank interleaving enabled */ |
||||||
|
.rtt_nom = CONFIG_RTT_NOM, |
||||||
|
.rtt_wr = CONFIG_RTT_WR, |
||||||
|
.ralat = CONFIG_RALAT, /* Read additional latency */ |
||||||
|
.walat = CONFIG_WALAT, /* Write additional latency */ |
||||||
|
.mif3_mode = 3, /* Command prediction working mode */ |
||||||
|
#ifdef CONFIG_DDR3 |
||||||
|
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ |
||||||
|
.sde_to_rst = 0x10, /* JEDEC value for LPDDR2 - 200us */ |
||||||
|
.pd_fast_exit = 0, /* immaterial for calibration */ |
||||||
|
.ddr_type = DDR_TYPE_DDR3, |
||||||
|
#else |
||||||
|
.rst_to_cke = 0x10, /* JEDEC value for LPDDR2: 200us */ |
||||||
|
.sde_to_rst = 0, /* LPDDR2 does not need this field */ |
||||||
|
.pd_fast_exit = 0, /* immaterial for calibration */ |
||||||
|
.ddr_type = DDR_TYPE_LPDDR2, |
||||||
|
#endif |
||||||
|
.refsel = CONFIG_REFSEL, |
||||||
|
.refr = CONFIG_REFR, |
||||||
|
}; |
||||||
|
|
||||||
|
#ifdef CONFIG_MT41K512M16TNA |
||||||
|
/* Micron MT41K512M16TNA-125 */ |
||||||
|
static struct mx6_ddr3_cfg const ddrtype = { |
||||||
|
.mem_speed = 1600, |
||||||
|
.density = 8, |
||||||
|
.width = 16, |
||||||
|
.banks = 8, |
||||||
|
.rowaddr = 15, |
||||||
|
.coladdr = 10, |
||||||
|
.pagesz = 1, |
||||||
|
.trcd = 1375, |
||||||
|
.trcmin = 5062, |
||||||
|
.trasmin = 3750, |
||||||
|
}; |
||||||
|
#elif defined(CONFIG_MT41K128M16JT) |
||||||
|
/* Micron MT41K128M16JT-125 */ |
||||||
|
static struct mx6_ddr3_cfg const ddrtype = { |
||||||
|
.mem_speed = 1600, |
||||||
|
.density = 2, |
||||||
|
.width = 16, |
||||||
|
.banks = 8, |
||||||
|
.rowaddr = 14, |
||||||
|
.coladdr = 10, |
||||||
|
.pagesz = 2, |
||||||
|
.trcd = 1375, |
||||||
|
.trcmin = 4875, |
||||||
|
.trasmin = 3500, |
||||||
|
}; |
||||||
|
#elif defined(CONFIG_H5TQ4G63AFR) |
||||||
|
/* Hynix H5TQ4G63AFR */ |
||||||
|
static struct mx6_ddr3_cfg const ddrtype = { |
||||||
|
.mem_speed = 1600, |
||||||
|
.density = 4, |
||||||
|
.width = 16, |
||||||
|
.banks = 8, |
||||||
|
.rowaddr = 15, |
||||||
|
.coladdr = 10, |
||||||
|
.pagesz = 2, |
||||||
|
.trcd = 1375, |
||||||
|
.trcmin = 4875, |
||||||
|
.trasmin = 3500, |
||||||
|
}; |
||||||
|
#elif defined CONFIG_H5TQ2G63DFR |
||||||
|
/* Hynix H5TQ2G63DFR */ |
||||||
|
static struct mx6_ddr3_cfg const ddrtype = { |
||||||
|
.mem_speed = 1333, |
||||||
|
.density = 2, |
||||||
|
.width = 16, |
||||||
|
.banks = 8, |
||||||
|
.rowaddr = 14, |
||||||
|
.coladdr = 10, |
||||||
|
.pagesz = 2, |
||||||
|
.trcd = 1350, |
||||||
|
.trcmin = 4950, |
||||||
|
.trasmin = 3600, |
||||||
|
}; |
||||||
|
#elif defined(CONFIG_MT42L256M32D2LG) |
||||||
|
/* Micron MT42L256M32D2LG */ |
||||||
|
static struct mx6_lpddr2_cfg ddrtype = { |
||||||
|
.mem_speed = 800, |
||||||
|
.density = 4, |
||||||
|
.width = 32, |
||||||
|
.banks = 8, |
||||||
|
.rowaddr = 14, |
||||||
|
.coladdr = 10, |
||||||
|
.trcd_lp = 2000, |
||||||
|
.trppb_lp = 2000, |
||||||
|
.trpab_lp = 2250, |
||||||
|
.trasmin = 4200, |
||||||
|
}; |
||||||
|
#elif defined(CONFIG_MT29PZZZ4D4BKESK) |
||||||
|
/* Micron MT29PZZZ4D4BKESK */ |
||||||
|
static struct mx6_lpddr2_cfg ddrtype = { |
||||||
|
.mem_speed = 800, |
||||||
|
.density = 4, |
||||||
|
.width = 32, |
||||||
|
.banks = 8, |
||||||
|
.rowaddr = 14, |
||||||
|
.coladdr = 10, |
||||||
|
.trcd_lp = 2000, |
||||||
|
.trppb_lp = 2000, |
||||||
|
.trpab_lp = 2250, |
||||||
|
.trasmin = 4200, |
||||||
|
}; |
||||||
|
#else |
||||||
|
#error please select DDR type using menuconfig |
||||||
|
#endif |
||||||
|
|
||||||
|
static void ccgr_init(void) |
||||||
|
{ |
||||||
|
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; |
||||||
|
|
||||||
|
/* FIXME: these should probably be checked, especially
|
||||||
|
* for i.MX6SL, UL, ULL |
||||||
|
*/ |
||||||
|
writel(0x00C03F3F, &ccm->CCGR0); |
||||||
|
writel(0x0030FC03, &ccm->CCGR1); |
||||||
|
writel(0x0FFFC000, &ccm->CCGR2); |
||||||
|
writel(0x3FF00000, &ccm->CCGR3); |
||||||
|
writel(0x00FFF300, &ccm->CCGR4); |
||||||
|
writel(0x0F0000C3, &ccm->CCGR5); |
||||||
|
writel(0x000003FF, &ccm->CCGR6); |
||||||
|
} |
||||||
|
|
||||||
|
static void display_calibration(struct mx6_mmdc_calibration *calib) |
||||||
|
{ |
||||||
|
printf(".p0_mpdgctrl0\t= 0x%08X\n", calib->p0_mpdgctrl0); |
||||||
|
printf(".p0_mpdgctrl1\t= 0x%08X\n", calib->p0_mpdgctrl1); |
||||||
|
printf(".p0_mprddlctl\t= 0x%08X\n", calib->p0_mprddlctl); |
||||||
|
printf(".p0_mpwrdlctl\t= 0x%08X\n", calib->p0_mpwrdlctl); |
||||||
|
printf(".p0_mpwldectrl0\t= 0x%08X\n", calib->p0_mpwldectrl0); |
||||||
|
printf(".p0_mpwldectrl1\t= 0x%08X\n", calib->p0_mpwldectrl1); |
||||||
|
if (sysinfo.dsize == 2) { |
||||||
|
printf(".p1_mpdgctrl0\t= 0x%08X\n", calib->p1_mpdgctrl0); |
||||||
|
printf(".p1_mpdgctrl1\t= 0x%08X\n", calib->p1_mpdgctrl1); |
||||||
|
printf(".p1_mprddlctl\t= 0x%08X\n", calib->p1_mprddlctl); |
||||||
|
printf(".p1_mpwrdlctl\t= 0x%08X\n", calib->p1_mpwrdlctl); |
||||||
|
printf(".p1_mpwldectrl0\t= 0x%08X\n", calib->p1_mpwldectrl0); |
||||||
|
printf(".p1_mpwldectrl1\t= 0x%08X\n", calib->p1_mpwldectrl1); |
||||||
|
} |
||||||
|
#ifdef CONFIG_IMXIMAGE_OUTPUT |
||||||
|
printf("DATA 4 MX6_MMDC_P0_MPDGCTRL0\t= 0x%08X\n", calib->p0_mpdgctrl0); |
||||||
|
printf("DATA 4 MX6_MMDC_P0_MPDGCTRL1\t= 0x%08X\n", calib->p0_mpdgctrl1); |
||||||
|
printf("DATA 4 MX6_MMDC_P0_MPRDDLCTL\t= 0x%08X\n", calib->p0_mprddlctl); |
||||||
|
printf("DATA 4 MX6_MMDC_P0_MPWRDLCTL\t= 0x%08X\n", calib->p0_mpwrdlctl); |
||||||
|
printf("DATA 4 MX6_MMDC_P0_MPWLDECTRL0\t= 0x%08X\n", |
||||||
|
calib->p0_mpwldectrl0); |
||||||
|
printf("DATA 4 MX6_MMDC_P0_MPWLDECTRL1\t= 0x%08X\n", |
||||||
|
calib->p0_mpwldectrl1); |
||||||
|
if (sysinfo.dsize == 2) { |
||||||
|
printf("DATA 4 MX6_MMDC_P1_MPDGCTRL0\t= 0x%08X\n", |
||||||
|
calib->p1_mpdgctrl0); |
||||||
|
printf("DATA 4 MX6_MMDC_P1_MPDGCTRL1\t= 0x%08X\n", |
||||||
|
calib->p1_mpdgctrl1); |
||||||
|
printf("DATA 4 MX6_MMDC_P1_MPRDDLCTL\t= 0x%08X\n", |
||||||
|
calib->p1_mprddlctl); |
||||||
|
printf("DATA 4 MX6_MMDC_P1_MPWRDLCTL\t= 0x%08X\n", |
||||||
|
calib->p1_mpwrdlctl); |
||||||
|
printf("DATA 4 MX6_MMDC_P1_MPWLDECTRL0\t= 0x%08X\n", |
||||||
|
calib->p1_mpwldectrl0); |
||||||
|
printf("DATA 4 MX6_MMDC_P1_MPWLDECTRL1\t= 0x%08X\n", |
||||||
|
calib->p1_mpwldectrl1); |
||||||
|
} |
||||||
|
#endif |
||||||
|
} |
||||||
|
|
||||||
|
/*
|
||||||
|
* called from C runtime startup code (arch/arm/lib/crt0.S:_main) |
||||||
|
* - we have a stack and a place to store GD, both in SRAM |
||||||
|
* - no variable global data is available |
||||||
|
*/ |
||||||
|
void board_init_f(ulong dummy) |
||||||
|
{ |
||||||
|
int errs; |
||||||
|
struct mx6_mmdc_calibration calibration = {0}; |
||||||
|
|
||||||
|
memset((void *)gd, 0, sizeof(struct global_data)); |
||||||
|
|
||||||
|
/* write leveling calibration defaults */ |
||||||
|
calibration.p0_mpwrdlctl = 0x40404040; |
||||||
|
calibration.p1_mpwrdlctl = 0x40404040; |
||||||
|
|
||||||
|
/* setup AIPS and disable watchdog */ |
||||||
|
arch_cpu_init(); |
||||||
|
|
||||||
|
ccgr_init(); |
||||||
|
|
||||||
|
SETUP_IOMUX_PADS(uart_pads); |
||||||
|
|
||||||
|
/* setup GP timer */ |
||||||
|
timer_init(); |
||||||
|
|
||||||
|
/* UART clocks enabled and gd valid - init serial console */ |
||||||
|
preloader_console_init(); |
||||||
|
|
||||||
|
if (sysinfo.dsize != 1) { |
||||||
|
if (is_cpu_type(MXC_CPU_MX6SX) || |
||||||
|
is_cpu_type(MXC_CPU_MX6UL) || |
||||||
|
is_cpu_type(MXC_CPU_MX6SL)) { |
||||||
|
printf("cpu type 0x%x doesn't support 64-bit bus\n", |
||||||
|
get_cpu_type()); |
||||||
|
reset_cpu(0); |
||||||
|
} |
||||||
|
} |
||||||
|
#ifdef CONFIG_MX6SL |
||||||
|
mx6sl_dram_iocfg(CONFIG_DDRWIDTH, &mx6sl_ddr_ioregs, |
||||||
|
&mx6sl_grp_ioregs); |
||||||
|
#else |
||||||
|
if (is_cpu_type(MXC_CPU_MX6Q)) { |
||||||
|
mx6dq_dram_iocfg(CONFIG_DDRWIDTH, &mx6dq_ddr_ioregs, |
||||||
|
&mx6dq_grp_ioregs); |
||||||
|
} else { |
||||||
|
mx6sdl_dram_iocfg(CONFIG_DDRWIDTH, &mx6sdl_ddr_ioregs, |
||||||
|
&mx6sdl_grp_ioregs); |
||||||
|
} |
||||||
|
#endif |
||||||
|
mx6_dram_cfg(&sysinfo, &calibration, &ddrtype); |
||||||
|
|
||||||
|
errs = mmdc_do_write_level_calibration(&sysinfo); |
||||||
|
if (errs) { |
||||||
|
printf("error %d from write level calibration\n", errs); |
||||||
|
} else { |
||||||
|
errs = mmdc_do_dqs_calibration(&sysinfo); |
||||||
|
if (errs) { |
||||||
|
printf("error %d from write level calibration\n", errs); |
||||||
|
} else { |
||||||
|
printf("completed successfully\n"); |
||||||
|
mmdc_read_calibration(&sysinfo, &calibration); |
||||||
|
display_calibration(&calibration); |
||||||
|
} |
||||||
|
} |
||||||
|
reset_cpu(0); |
||||||
|
} |
@ -0,0 +1,33 @@ |
|||||||
|
CONFIG_ARM=y |
||||||
|
CONFIG_ARCH_MX6=y |
||||||
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y |
||||||
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y |
||||||
|
CONFIG_MX6_DDRCAL=y |
||||||
|
CONFIG_TARGET_MX6MEMCAL=y |
||||||
|
CONFIG_SPL_SERIAL_SUPPORT=y |
||||||
|
CONFIG_SPL_WATCHDOG_SUPPORT=y |
||||||
|
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,SPL,MX6QDL" |
||||||
|
CONFIG_SPL=y |
||||||
|
CONFIG_HUSH_PARSER=y |
||||||
|
# CONFIG_MMC is not set |
||||||
|
# CONFIG_CMD_BOOTD is not set |
||||||
|
# CONFIG_CMD_BOOTM is not set |
||||||
|
# CONFIG_CMD_ELF is not set |
||||||
|
# CONFIG_CMD_IMI is not set |
||||||
|
# CONFIG_CMD_IMLS is not set |
||||||
|
# CONFIG_CMD_XIMG is not set |
||||||
|
# CONFIG_CMD_EXPORTENV is not set |
||||||
|
# CONFIG_CMD_IMPORTENV is not set |
||||||
|
# CONFIG_CMD_EDITENV is not set |
||||||
|
# CONFIG_CMD_SAVEENV is not set |
||||||
|
# CONFIG_CMD_ENV_EXISTS is not set |
||||||
|
CONFIG_CMD_MEMTEST=y |
||||||
|
CONFIG_CMD_MEMINFO=y |
||||||
|
# CONFIG_CMD_LOADB is not set |
||||||
|
# CONFIG_CMD_LOADS is not set |
||||||
|
# CONFIG_CMD_FLASH is not set |
||||||
|
# CONFIG_CMD_FPGA is not set |
||||||
|
# CONFIG_CMD_NET is not set |
||||||
|
# CONFIG_CMD_NFS is not set |
||||||
|
CONFIG_CMD_CACHE=y |
||||||
|
CONFIG_REGEX=y |
@ -0,0 +1,59 @@ |
|||||||
|
/*
|
||||||
|
* Copyright (C) 2010-2011 Freescale Semiconductor, Inc. |
||||||
|
* |
||||||
|
* Configuration settings for the Boundary Devices Nitrogen6X |
||||||
|
* and Freescale i.MX6Q Sabre Lite boards. |
||||||
|
* |
||||||
|
* SPDX-License-Identifier: GPL-2.0+ |
||||||
|
*/ |
||||||
|
|
||||||
|
#ifndef __CONFIG_H |
||||||
|
#define __CONFIG_H |
||||||
|
|
||||||
|
/* SPL */ |
||||||
|
|
||||||
|
#include "mx6_common.h" |
||||||
|
#include "imx6_spl.h" |
||||||
|
|
||||||
|
#undef CONFIG_FSL_ESDHC |
||||||
|
#undef CONFIG_MMC |
||||||
|
#undef CONFIG_SPL_MMC_SUPPORT |
||||||
|
#undef CONFIG_GENERIC_MMC |
||||||
|
#undef CONFIG_CMD_FUSE |
||||||
|
|
||||||
|
#define CONFIG_SYS_MEMTEST_START 0x10000000 |
||||||
|
#define CONFIG_SYS_MEMTEST_END 0x20000000 |
||||||
|
#define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024) |
||||||
|
|
||||||
|
#define CONFIG_MXC_UART |
||||||
|
#ifdef CONFIG_SERIAL_CONSOLE_UART1 |
||||||
|
#if defined(CONFIG_MX6SL) |
||||||
|
#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR |
||||||
|
#else |
||||||
|
#define CONFIG_MXC_UART_BASE UART1_BASE |
||||||
|
#endif |
||||||
|
#elif defined(CONFIG_SERIAL_CONSOLE_UART2) |
||||||
|
#define CONFIG_MXC_UART_BASE UART2_BASE |
||||||
|
#else |
||||||
|
#error please define serial console (CONFIG_SERIAL_CONSOLE_UARTx) |
||||||
|
#endif |
||||||
|
#define CONFIG_BAUDRATE 115200 |
||||||
|
|
||||||
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + 16) |
||||||
|
|
||||||
|
/* Physical Memory Map */ |
||||||
|
#define CONFIG_NR_DRAM_BANKS 1 |
||||||
|
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR |
||||||
|
|
||||||
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM |
||||||
|
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR |
||||||
|
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE |
||||||
|
|
||||||
|
#define CONFIG_SYS_INIT_SP_OFFSET \ |
||||||
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
||||||
|
#define CONFIG_SYS_INIT_SP_ADDR \ |
||||||
|
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) |
||||||
|
|
||||||
|
#define CONFIG_ENV_SIZE (8 * 1024) |
||||||
|
|
||||||
|
#endif /* __CONFIG_H */ |
Loading…
Reference in new issue