operation. We waste some time however, by writing back the exact same
value that was already set in the chip. Let us thus only configure the
chip if the data is different.
Currently the DRAM bus gate and reset is changed at the same time in
H6 DRAM initialization code, which disobeys the user manual's
programming guide.
Fix the sequence by follow the sequence suggested by the user manual
(ungate the bus clock after release the reset signal).
By some experiments it seems to fix the DRAM size detection failure that
rarely happens.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
"default" lines in Kconfig are processed in order, the first hit will
stop considering subsequent lines. In the case of the DRAM_ODT_EN symbol
that means that everything following the first two lines will never be
checked:
------------
config DRAM_ODT_EN
bool "sunxi dram odt enable"
default n if !MACH_SUN8I_A23
default y if MACH_SUN8I_A23
default y if MACH_SUN8I_R40
default y if MACH_SUN50I
------------
Assuming that the "default y" for the A64 and the R40 were a deliberate
choice, fix the Kconfig stanza to take this into account.
Also remove the now redundant lines from the respective defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: droped 'default n' on original change]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # A64, R40
Tested-by: Chen-Yu Tsai <wens@csie.org> # A23
Allwinner H6 is a new SoC from Allwinner features USB3 and PCIe
interfaces.
This patch adds support for it.
The corresponding DTSI file, from Linux next-20180720, is also
introduced.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC comes with a set of new DRAM controller+PHY combo.
Both the controller and the PHY seem to be originate from DesignWare,
and are similar to the ones in ZynqMP SoCs.
This commit introduces an initial DRAM driver for H6, which contains
only LPDDR3 support. The currently known SBCs with H6 all come with
LPDDR3 memory, including Pine H64 and several Orange Pi's.
The BSP DRAM initialization code is closed source and violates GPL. Code
in this commit is written by experimenting, referring the code/document
of other users of the IPs (mainly the ZynqMP, as it's the only found PHY
reference) and disassebling the BSP blob.
Thanks for Jernej Skrabec for review and fix some issues in this driver
(including the most critical one which made it to work), and rewrite
some code from register dump!
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The UART0 on H6 is available at PH bank (and PF bank, but the PF one is
muxed with SD card).
Add pinmux configuration.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The H6 SoC has a sun6i-style watchdog in its timer part.
Enable the usage of it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The new Allwinner H6 SoC has a brand new CCU layout.
Add clock code for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner H6 has a different RVBAR address with A64/H5.
Add conditional RVBAR configuration into the code which does RMR switch.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The new Allwinner H6 SoC has its SRAM A1 at neither 0x0 nor 0x10000, but
it's at 0x20000. Thus the SUNXI_HIGH_SRAM option needs to be refactored
to support this new configuration.
Change it to SUNXI_SRAM_ADDRESS, which holds the real address of SRAM
A1 in the memory map.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Use the driver model for MMC and SATA, in preparation for CONFIG_BLK
defaulting to y.
Tested on A10 Cubieboard.
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The Allwinner A64 SoCs suffers from an arch timer implementation erratum,
where sometimes the lower 11 bits of the counter value erroneously
become all 0's or all 1's [1]. This leads to sudden jumps, both forwards and
backwards, with the latter one often showing weird behaviour.
Port the workaround proposed for Linux to U-Boot and activate it for all
A64 boards.
This fixes crashes when accessing MMC devices (SD cards), caused by a
recent change to actually use the counter value for timeout checks.
Fixes: 5ff8e54888 ("sunxi: improve throughput
in the sunxi_mmc driver")
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-May/576886.html
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Guillaume Gardet <guillaume.gardet@free.fr>
Allwinner PHY USB code is now part of generic-phy framework,
so drop existing legacy handling like arch/arm/mach-sunxi.c
and related code areas.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner USB PHY handling can be done through driver-model
generic-phy so add the generic-phy ops to relevant places
on host and musb sunxi driver and enable them in respective
SOC's.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add proper and simple kconfig option for dram_sun8i_a83t.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun8i_a33.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun8i_a23.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun9i.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun4i.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun6i.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add simple and meaningful kconfig option for pmic_bus.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add simple and meaningful kconfig option for rsb.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
SUN6I_PRCM is also used for SUN8I and SUN9I, so
select the same on respective MACH types.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add simple and meaningful kconfig option for p2wi.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add simple and meaningful kconfig option for prcm.c
instead of using MACH type on Makefile.
PRCM (Power/Reset/Clock Management) is considered as a
Multi-Functional Device, so used the same on Kconfig definition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
This SUNXI variant SPL SPI code doesn't use either SPI or
SPL_FLASG subsystems due to size constraints and also placing
this code in drivers/mtd/spi will unnecessary build SPI_FLASH
code(if defined) which never required, hence moved to arch area.
And also renamed the file according to kconfig which resembles
proper name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The goal of this patch is to clean up the code related to choosing SPL
MMC boot mode.
The spl_boot_mode() now is called only in spl_mmc_load_image() function,
which is only compiled in if CONFIG_SPL_MMC_SUPPORT is enabled.
To achieve the goal, all per mach/arch implementations eligible for
unification has been replaced with one __weak implementation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com> (For ZynqMP)
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Some H5 boards are designed to start at 1.1V CPUx voltage (e.g. Nano Pi
NEO2), which may not work properly at 1008MHz if the chip's quality is
not so good.
Lower the default CPUx frequency of H5 to 816MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Extend DE2 driver with LCD support. Tested on Pinebook which is based
on A64 and has ANX6345 eDP bridge with eDP panel connected to it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: rebased v5 on u-boot-video/master]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
As the support of EFI boot on Allwinner H3 is broken, we still need to
use simplefb to pass the framebuffer to Linux.
Add code to setup simplefb for Allwinner DE2 driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add an option to indicate that the video driver should setup a SimpleFB
node that passes the video framebuffer initialized by U-Boot to the
operating system kernel.
Currently only the Allwinner DE driver uses this option, and the
definition of this option in the sunxi-common.h config header is
converted to an imply of this option from CONFIG_VIDEO_SUNXI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sunxi DE1 video option used to be CONFIG_VIDEO, which has the same
name as the "Enable legacy video support" option in
drivers/video/Kconfig.
Change the option name to CONFIG_VIDEO_SUNXI, which is really used by
Makefile under drivers/video/sunxi/, and defined in sunxi-common.h
when CONFIG_VIDEO is selected before this change. Now CONFIG_VIDEO_SUNXI
selects CONFIG_VIDEO and the usages of CONFIG_VIDEO in sunxi Kconfig and
config headers are all converted to use CONFIG_VIDEO_SUNXI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
All the new SoCs from Allwinner since the A33 have had the phy_ctl offset
at 0x410 instead of 0x404 that was used on the previous SoCs.
Instead of adding more and more special cases as the number of SoCs grow,
let's invert the test to have 0x410 by default, and the (hopefully) fixed
number of old SoCs being the exception.
Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
U-Boot itself might need to identify the boot device, for example to be
able to tell where to load the kernel from when several options are
possible.
Move the logic of spl_boot_device to a function that is compiled both for
the SPL and the main binary.
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The eMMC controller for the A83T uses the new operating mode. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).
Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.
Also expand the help for the 'nowhere' option and move it to the top since
it is the default.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.
As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig. Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PRCM of H3/H5 SoCs have a secure/non-secure switch, which controls
the access to some clock/power related registers in PRCM.
Current Linux kernel will access the CPUS (AR100) clock in the PRCM
block, so the PRCM should be switched to non-secure.
Add code to switch the PRCM to non-secure.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
As we added LPDDR3 support in the former patch, we need a set of timing
info to really enable it.
Add the timing info used by stock boot0.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some A64 boards (SoPine and Pinebook production batch) use LPDDR3 DRAM
chips.
Add support for LPDDR3 DRAM in the DesignWare-like DRAM controller code.
Real LPDDR3 chips' support is not added yet in this commit.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
As we have already support for the DesignWare DRAM controller and the
integrated DDR2 chip of V3s, let's enable the SPL support for V3s.
This patch also contains the default DRAM configuration for V3s.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner V3s features a DRAM controller like the on in H3, but with a
DDR2 DRAM.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner V3s SoC features a co-packaged DDR2 DRAM chip, which needs its
timing param.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The DesignWare-like DRAM code used to set the controller defaultly to
single rank mode, which makes it not able to detect the second rank.
Set the default value to dual rank, thus the rank detection code can
work and finally the rank setting will be the correct value.
Currently we know little about the dual-rank on R40, and the usage
of A15 address line seems to be breaking dual-rank support. The only R40
board currently available (Sinovoip Banana Pi M2 Ultra) uses A15 rather
than dual-rank, thus we cannot do research for it. So dual rank detection
is temporarily disabled on R40.
This change is tested on a Orange Pi One (H3, single rank), a Pine64+
2GiB version (A64, single rank) , a Pinebook early prototype with DDR3
(A64, dual rank) and a SoPine with some LPDDR3 patch (A64, dual CS pins
on one chip).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Merlijn Wajer
Icenowy Zheng
Andre Przywara
Adam Sampson
Chris Packham
Jagan Teki
Lokesh Vutla
Tom Rini
Lukasz Majewski
Vasily Khoruzhick
Maxime Ripard
Simon Glass
Philipp Tomsich
Icenowy Zheng