Add a common helper that will set the PHY connection type based on enum.
We use this on eTSEC, UCC, and will with Fman in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Clean up Makefile, and drop a lot of the config.mk files on the way.
We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
When planning for more generalization and Makefile cleanup it became
obvious that the introduction of a separate CONFIG_MK_ name space for
config options that were set through scripting in the Makefile was
not a good idea.
Originally the idea was to provide a script-free approach to supply
configuration options - there was no real need for a separate name
space. But when we now convert the existing Makefile entries to make
use of this approach, it would mean that we have to touch a large
number of board config files and add #ifdef / #define sequences to
"convert" from the CONFIG_MK_ to the CONFIG_ name space.
It seems much cleaner to get rid of this somewhat arbitrary _MK
string now for the few boards that actually use it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Enable half drive strength, set RTT to 60Ohm and set write leveling override.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The original code maps boot flash as non-cacheable region. When calling
relocate_code in flash to copy u-boot from flash to ddr, every loop copy command
is read from flash. The flash read speed will be the bottleneck, which consuming
long time to do this operation. To resovle this, map the boot flash as
write-through cache via tlb. And set tlb to remap the flash after code
executing in ddr, to confirm flash erase operation properly done.
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously we used an alias the pci node to determine which node to
fixup or delete. Now we use the new fdt_node_offset_by_compat_reg to
find the node to update.
Additionally, we replace the code in each board with a single macro call
that makes assumes uniform naming and reduces duplication in this area.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers. Merge
this into a single spot.
To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.
In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.
I have done a successful ppc build all and tested a board or two from
each processor family.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CPUDIR variable points to the location of a target's CPU directory.
Currently, it is set to cpu/$CPU. However, using $CPUDIR will allow for
more flexibility in the future. It lays the groundwork for reorganizing
U-Boot's directory structure to support a layout such as:
arch/$ARCH/cpu/$CPU/* (architecture with multiple CPU types)
arch/$ARCH/cpu/* (architecture with one CPU type)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
When referring to PCIe and USB 'endpoint' is the standard naming
convention.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>
Thanks to "Errata to MPC8569E PowerQUICC III Integrated Host Processor
Family Reference Manual, Rev. 0" document, which describes all eSDHC
pins, we can add 4-bits eSDHC support for MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Setup QE pin multiplexing for USB function, configure needed BCSRs
and add some fdt fixups.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To make QE UART usable by Linux we should setup pin multiplexing
and turn UCC2 Ethernet node into UCC2 QE UART node.
Also, QE UART is mutually exclusive with UART0, so we can't enable
it if eSDHC is in 4-bits mode on pilot boards, or if it's a prototype
board with eSDHC in 1- or 4-bits mode.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SPI Flash (M25P40) is connected to the SPI1 bus, we need a few
qe_iop entries to actually enable SPI1 on these boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch sets memory window for Serial RapidIO on MPC8569E-MDS
boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add some defines, and adjust TLBe setup to include some
space for eLBC NAND.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
eSDHC is mutually exlusive with UART0 (in 4-bits mode) and I2C2
(in 1-bit mode). When eSDHC is used, we should switch u-boot console to
UART1, and make the proper device-tree fixups.
Because of an erratum in prototype boards it is impossible to use eSDHC
without disabling UART0 (which makes it quite easy to 'brick' the board
by simply issung 'setenv hwconfig esdhc', and not able to interact with
U-Boot anylonger).
So, but default we assume that the board is a prototype, which is a most
safe assumption. There is no way to determine board revision from a
register, so we use hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactor the code into a simple bitmask lookup table that determines if
a given PCI controller is enabled and if its in host/root-complex or
agent/end-point mode.
Each processor in the PQ3/MPC86xx family specified different encodings
for the cfg_host_agt[] and cfg_IO_ports[] boot strapping signals.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactor the code into a simple bitmask lookup table that determines if
a given PCI controller is enabled and if its in host/root-complex or
agent/end-point mode.
Each processor in the PQ3/MPC86xx family specified different encodings
for the cfg_host_agt[] and cfg_IO_ports[] boot strapping signals.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are really no differences between all the 85xx linker scripts so
we can just move to a single common one. Board code is still able to
override the common one if need be.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For historic reasons we had defined some additional PLATFORM_CPPFLAGS
like:
PLATFORM_CPPFLAGS += -DCONFIG_E500=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC8548=1
However these are all captured in the config.h and thus redudant.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Every platform that calls fsl_pci_init calls fsl_pci_setup_inbound_windows
before it calls fsl_pci_init. There isn't any reason to just call it
from fsl_pci_init and simplify things a bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Every platform that calls fsl_pci_init calls pci_setup_indirect before
it calls fsl_pci_init. There isn't any reason to just call it from
fsl_pci_init and simplify things a bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to
support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to
enalbe_mpc8569mds_qe_uec which is more accurate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8569 UART1 signals are muxed with PortF bit[9-12], we need to define
those pins before using UART1.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The BCSR17[7] = 1 will unlock the write protect of FLASH.
The WP# pin only controls the write protect of top/bottom sector,
That is why we can save env, but we can't write the first sector
before the patch.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Currently the clk_adj is 6 (3/4 cycle), The settings will cause
the DDR controller hang at the data init. Change the clk_adj
from 6 to 4 (1/2 cycle), make the memory system stable.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Rename the pci header for FSL HW so we can move some prototypes
in there and stop doing explicit externs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala
Wolfgang Denk
Haiying Wang
Becky Bruce
Peter Tyser
Liu Yu
Anton Vorontsov
Kumar Gala
Dave Liu