Simon Glass's proposal to fix this on Seaboard was NAK'd, so I
removed his NS16550 references and added a small delay before
SPI/UART muxing. Tested on my Seaboard with large SPI reads/writes
and saw no corruption (crc's matched) and no spurious comm chars.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jimmy Zhang <jimmzhang@nvidia.com>
Remove unnecessary brackets.
Unwrap lines which are below 80 chars.
Single line comment as single line (as the rest).
Moved init values to the source code.
cc: s-paulraj@ti.com
cc: khasim@ti.com
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
The beagle board uses the background color to show an orange screen during
startup. This patch adds the ability to add a frame buffer, with the
intention not to break the beagle board use case (I don't have one).
videomodes.c is not used. Scrolling depends on this patch:
http://patchwork.ozlabs.org/patch/155662/
cc: trini@ti.com
cc: s-paulraj@ti.com
cc: khasim@ti.com
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
s6e8ax0 panel has many panel of types. This patch support another panel
on TIZEN lunchbox board(HWREVISION 2). This panel has reversed panel
display type. So, I had added necessary command.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr"). After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Add tegra_i2c_get_dvc_bus_num() to obtain the I2C bus number of DVC bus.
This allows us to talk to the PMU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add code to set up the warm boot area in the Tegra CPU ready for a
resume after suspend.
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Power supplies must be adjusted in line with clock frequency. This code
provides a simple routine to set the voltage to allow operation at maximum
frequency.
- Split PMU code into separate TPS6586X driver
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for setting up the memory controller parameters. Boards
can set up an appropriate table in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a basic header file for this register, to be filled in as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We want to know which type of chip we are running on - the Tegra
family has several SKUs. This can be determined by reading a
fuse register, so add this function to ap20.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These headers provide access to additional Tegra features.
flow - start/stop CPUs
sdram - parameters for SDRAM
fuse - access to on-chip fuses / security settings
gp_padctl - pad control and general purpose registers
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add clock_ll_read_pll() to read PLL parameters and clock_get_osc_bypass()
to find out if the Oscillator is bypassed. These are needed by warmboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We want to include this from board code, so move the header into
an easily-accessible location.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass memory size from SPL via structure located in SRAM instead of SCRATCH
registers. This allows passing more data about boot from SPL to U-Boot, like the
boot mode pads configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
After an update to the MX51 reference manual (Rev. 5), the
values of the PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH
are now clearly wrong:
"Bit 13:
High / Low Output Voltage Range. This bit selects the output voltage mode for
SD2_CMD. 0 High output voltage mode
1 Low output voltage mode"
The values are currently negated in code - fixed.
Reported-by: David Jander <david.jander@protonic.nl>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: David Jander <david.jander@protonic.nl>
Acked-by: David Jander <david.jander@protonic.nl>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information.
The kernel uses this data to distinguish between Dialog versus mc34708 based boards,
and also to distinguish between revA and revB of the mc34708 based boards.
Suggested-by: Yu Li <yk@magniel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
types.h must be included in imx-regs.h if one wants to include
imx-regs.h in a board configuration file. That for one's part is
necessary, if one wants to use addresses defined in imx-regs.h.
For example, fsl_esdhc.c needs CONFIG_SYS_FSL_ESDHC_ADDR defined and
a proper thing is to define it with IMX_MMC_SDHCx_BASE in board
configuration file. This patch fixes the build in that case.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
Defining CONFIG_FSL_ESDHC brings in a call to get_clocks, so let's
implement get_clocks function. This is how it seems to be implemented
elsewhere.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
Init the core regulator voltage to 1.2V. This is required for the correct
functioning of the GPU and when the ARM LDO is set to 1.225V. This is a
workaround to fix some memory clock jitter.
Note: This should be but can't be done in the DCD. The bootloader
prevents access to the ANATOP registers.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Chen <b02280@freescale.com>
CC: Jason Liu <r64343@freescale.com>
CC: Ranjani Vaidyanathan <ra5478@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
Print CPU information within board_late_init().
This is in preparation for adding 1GHz support, which requires programming a PMIC
via I2C. As I2C is only available after relocation, print the CPU information
later at board_late_init(), so that the CPU frequency can be printed correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
mx5: Add clock config interface
Add clock config interface support, so that we
can configure CPU or DDR clock in the later init
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
get_ahb_clk() is a common function between mx5 and mx6.
Place it into imx-common directory.
Cc: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The MX53 SATA interface can use an internal clock (USB PHY1)
instead of an external clock. This is an undocumented feature, but used
on most Freescale's evaluation boards, such as MX53-loco.
As stated by Freescale's support:
Fuses (but not pins) may be used to configure SATA clocks.
Particularly the i.MX53 Fuse_Map contains the next information
about configuring SATA clocks :
SATA_ALT_REF_CLK[1:0] (offset 0x180C)
'00' - 100MHz (External)
'01' - 50MHz (External)
'10' - 120MHz, internal (USB PHY)
'11' - Reserved
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Add base address and MXC_SATA_CLK to return
the clock used for the SATA controller.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
EXYNOS SoC platform has MIPI-DSI controller and MIPI-DSI
based LCD Panel could be used with it. This patch supports MIPI-DSI driver
based Samsung SoC chip.
LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
board file and LCD panel driver specific function registered to mipi_dsim_ddi
structure at lcd panel init function called system init.
In the MIPI-DSI driver, find lcd panel driver by using registered
lcd panel name, and then initialize lcd panel driver.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch support EXYNOS FB and FIMD display drivers.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
To sets up lcd and mipi clock in EXYNOS display driver, added clock interface.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This is definitions of system registers and power mananagement registers for EXYNOS SoC.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
TZPC IP is common across Exynos based SoC'c. Renaming exynos5_tzpc
in arch/arm/include/asm/arch-exynos/tzpc.h to exynos_tzpc will allow generic
usase of tzpc.
Also modify board/samsung/smdk5250/tzpc_init.c to use exynos_tzpc.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Avoid using __attribute__ ((__packed__)) unless it's
absolutely necessary. "packed" will remove alignment
requirements for the respective objects and may cause
alignment issues unless alignment is also enforced
using a pragma.
Here, these packed attributes were causing alignment
faults in Thumb build.
Signed-off-by: Aneesh V <aneesh@ti.com>
This will add ARM specific over-rides for the defines
from linux/linkage.h
Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
The reset.S has the function to do a warm reset on OMAP
based socs. Moving this to a reset.c file so that this
acts a common layer to add any reset related functionality
for the future.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
PD_TIM bit field which specifies the power down timing is defined
to occupy bits 8-11, where as it is actually from 12-15 bits.
So correcting this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The full internal SRAM of size 128kb is public in the case of OMAP5 soc.
So change the base address accordingly.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The nominal opp vdd values as recommended for
ES1.0 silicon is set for mpu, core, mm domains using palmas.
Also used the right sequence to enable the vcores as per
a previous patch from Nishant Menon, which can be dropped now.
http://lists.denx.de/pipermail/u-boot/2012-March/119151.html
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Tom Warren
Jeroen Hofstee
Fabio Estevam
Donghwa Lee
Rajeshwari Shinde
Mike Frysinger
Simon Glass
Yen Lin
Jimmy Zhang
Marek Vasut
Marek Vasut
Stefano Babic
Timo Ketola
Eric Nelson
Dirk Behme
Fabio Estevam
Chander Kashyap
Grazvydas Ignotas
Aneesh V
SRICHARAN R
Balaji T K