This is a re-submission of the patch by Harald Welte
<laforge@openmoko.org> with minor modifications for rebase and changes
as suggested by Scott Wood <scottwood@freescale.com> [1] [2].
This patch enables the environment partition to have a run-time dynamic
location (offset) in the NAND flash. The reason for this is simply that
all NAND flashes have factory-default bad blocks, and a fixed compile
time offset would mean that sometimes the environment partition would
live inside factory bad blocks. Since the number of factory default
blocks can be quite high (easily 1.3MBytes in current standard
components), it is not economic to keep that many spare blocks inside
the environment partition.
With this patch and CONFIG_ENV_OFFSET_OOB enabled, the location of the
environment partition is stored in the out-of-band (OOB) data of the
first block in flash. Since the first block is where most systems boot
from, the vendors guarantee that the first block is not a factory
default block.
This patch introduces the 'nand env.oob' command, which can be called
from the u-boot command line. 'nand env.oob get' reads the address of
the environment partition from the OOB data, 'nand env.oob set
{offset,partition-name}' allows the setting of the marker by specifying
a numeric offset or a partition name.
[1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/43916
[2] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/79195
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Harald Welte <laforge@gnumonks.org>
Legacy NAND had been scheduled for removal. Any boards that use this
were already not building in the previous release due to an #error.
The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed. There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.
Signed-off-by: Scott Wood <scottwood@freescale.com>
nand_util currently uses size_t which is arch dependent and not always a
unsigned long. Now use loff_t, as does the linux mtd layer.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Rather than putting the function prototype for board_nand_init() in the one
place where it gets called, put it into nand.h so that every place that also
defines it gets the prototype. Otherwise, errors can go silently unnoticed
such as using the wrong return value (void rather than int) when defining
the function.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Implement block-skipping read/write, based on a patch from
Morten Ebbell Hestens <morten.hestnes@tandberg.com>.
Signed-off-by: Morten Ebbell Hestnes <morten.hestnes@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Some macros such as NAND_CTL_SETALE conflict between current and legacy
NAND, being defined by the subsystem in the former case and the board
config file in the latter.
Signed-off-by: Scott Wood <scottwood@freescale.com>
since nand_init() is expected to be called by other parts of u-boot, there
should be a prototype for it in nand.h
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
- JFFS2 related commands implemented in mtd-utils style
- Support for bad blocks
- Bad block testing commands
- NAND lock commands
Please take a look at doc/README.nand for more details
Patch by Guido Classen, 10 Oct 2006
Ben Gardiner
Scott Wood
Jean-Christophe PLAGNIOL-VILLARD
Mike Frysinger
Wolfgang Denk
William Juul
Stefan Roese
Wolfgang Denk
Wolfgang Denk