This is an enhancement that permits storing the environment file on an
EXT4 partition such as the root filesystem. It is based on the existing
FAT environment file code.
GPIO4_21 is the LAN8720 power pin, not the LAN8720 reset pin.
Fix that, so that we can have Ethernet functional again.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The stm_is_locked_sr() function is picked from Linux kernel. For reason
unknown, the 64bit data types used by the function and present in Linux
were replaced with 32bit unsigned ones, which causes trouble.
The testcase performed was done using ST M25P80 chip.
The command used was:
=> sf protect unlock 0 0x10000
The call chain starts in stm_unlock(), which calls stm_is_locked_sr()
with negative ofs argument. This works fine in Linux, where the "ofs"
is loff_t, which is signed long long, while this fails in U-Boot, where
"ofs" is u32 (unsigned int). Because of this signedness problem, the
expression past the return statement to be incorrectly evaluated to 1,
which in turn propagates back to stm_unlock() and results in -EINVAL.
The correction is very simple, just use the correctly sized data types
with correct signedness in the function to make it work as intended.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
TI QSPI driver directly typecasts fdt_addr_t to a pointer. This is
not strictly correct, as it gives a build warning when fdt_addr_t is u64.
So, use map_physmem for a proper typecasts.
This is inspired by commit 167efe01bc ("dm: ns16550: Use an address
instead of a pointer for the uart base")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Enable CONFIG_USB_ETHER_RTL8152 support for Odroid XU4 which
has support for RTL8153-CG gigabit Ethernet adapter,
connected over USB 3.0.
commit 9dc8ba19c5 added support
for Realtek 8152/8153 driver.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The DMC driver in v3.14 kernel[0] get the ddr setting from PMU_SYS_REG2,
and it expects uboot to store the value using a same protocol. But now
the ddr setting value is different with DMC, so if you enable the DMC,
system would crash in kernel. Correct the sdram setting here, according
to the requirements of kernel.
[0]
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/
chromeos-3.14/drivers/clk/rockchip/clk-rk3288-dmc.c
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
on v2016.03-rc3, size of SPL image compiled by gcc 5.3.0 is too large for
Firefly-RK3288. (it's fine for Rock2)
$ gcc --version
gcc (Ubuntu/Linaro 5.3.0-3ubuntu1~14.04) 5.3.0 20151204
Copyright (C) 2015 Free Software Foundation, Inc.
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
$ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin u-boot-spl-dtb.img
Warning: SPL image is too large (size 0x80d0) and will not boot
to reduce size of SPL image, this patch makes configure_emmc() empty for
Firefly-RK3288 as same as Rock2.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
emac may use dpll as clock parent, and it request the clock frequency
multiples of 50, so change ddr frequency to 400M.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
MIPS EL boards should define CONFIG_USE_PRIVATE_LIBGCC=y to work
with EB-only toolchains like the one from kernel.org. If one do
not globally set CONFIG_USE_PRIVATE_LIBGCC=y, the build fails with:
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o): compiled for a big endian system and target is little endian
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o): endianness incompatible with that of the selected emulation
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: failed to merge target specific data of file /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o)
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o): compiled for a big endian system and target is little endian
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o): endianness incompatible with that of the selected emulation
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: failed to merge target specific data of file /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o)
/work/git-trees/u-boot-mips/Makefile:1171: recipe for target 'u-boot' failed
One example for a failing build is Travis CI.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Purna Chandra Mandal <purna.mandal@microchip.com>
The "R" constraint supplies the address of an variable in a register. Use
"r" instead and adjust asm to supply the content of addr in a register
instead.
Fixes: 2b8bcc5a ("MIPS: avoid .set ISA for cache operations")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Following the previous patch, malloc() is never called before gd is set,
so we can remove the special-case check for this condition.
This reverts commit 854d2b9753 "dlmalloc: ensure gd is set for early
alloc".
Cc: Rabin Vincent <rabin@rab.in>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When running sandbox, the following phases occur, each with different
malloc implementations or behaviors:
1) Dynamic linker execution, using the dynamic linker's own malloc()
implementation. This is fully functional.
2) After U-Boot's malloc symbol has been hooked into the GOT, but before
any U-Boot code has run. This phase is entirely non-functional, since
U-Boot's gd symbol is NULL and U-Boot's initf_malloc() and
mem_malloc_init() have not been called.
At least on Ubuntu Xenial, the dynamic linker does make both malloc() and
free() calls during this phase. Currently these free() calls crash since
they dereference gd, which is NULL.
U-Boot itself makes no use of malloc() during this phase.
3) U-Boot execution after gd is set and initf_malloc() has been called.
This is fully functional, albeit via a very simple malloc()
implementation.
4) U-Boot execution after mem_malloc_init() has been called. This is fully
functional with a complete malloc() implementation.
Furthermore, if code that called malloc() during phase 1 calls free() in
phase 3 or later, it is likely that heap corruption will occur, since
U-Boot's malloc implementation will assume the pointer is part of its own
heap, although it isn't. I have not actively observed this happening.
To prevent phase 2 from happening, this patch makes all of U-Boot's malloc
library public symbols have hidden visibility. This prevents them from
being hooked into the GOT, so only code in the U-Boot binary itself
actually calls them; any other code will call into the standard C library
malloc(). This also avoids the "furthermore" issue mentioned above.
I have seen references to this GCC pragma in blog posts from 2008, and
RHEL5's ancient gcc appears to accept it fine, so I believe it's quite
safe to use it without checking gcc version.
Cc: Rabin Vincent <rabin@rab.in>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- The macro __BIGGEST_ALIGNMENT__ is gcc-specific. If it is not defined
we'll just assume 16. This is correct for at least the common cases
and LLVM does not provide an equivalent macro.
- When linking U-Boot we're passing -T to the linker, and while gcc will
just pass this along with LLVM we need to be specific.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we fall back to the FS code path when we don't find u-boot
at the raw sector offset, there is no good reason to not default to
raw boot.
With this patch, I can successfully boot u-boot from a raw sector
offset on beagle-xm.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch makes the U-Boot api export its structure address as an environment
variable, so it can be used to directly hint FreeBSD's loader of api's location.
The relevant FreeBSD loader change is currently under review at:
https://reviews.freebsd.org/D5492
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
Select 8-bit BCH ecc-scheme with s/w based error correction
- OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function should just return for unknown SoCs rather than writing
unexpected values to registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER
to guard the drivers/pinctrl/uniphier directory.
The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long, so rename it
into CONFIG_PINCTRL_UNIPHIER.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
While IECTRL is disabled, input signals are pulled-down internally.
If pin-muxing is set up first, glitch signals (Low to High transition)
might be input to hardware blocks.
Bad case scenario:
[1] The hardware block is already running before pinctrl is handled.
(the reset is de-asserted by default or by a firmware, for example)
[2] The pin-muxing is set up. The input signals to hardware block
are pulled-down by the chip-internal biasing.
[3] The pins are input-enabled. The signals from the board reach the
hardware block.
Actually, one invalid character is input to the UART blocks for such
SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the
power on reset.
To avoid such problems, pins should be input-enabled before muxing.
[ ported from Linux commit bac7f4c1bf5e7c6ccd5bb71edc015b26c77f7460 ]
Fixes: 5dc626f836 ("pinctrl: uniphier: add UniPhier pinctrl core support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary overcurrent
error which would then disable the host port.
The overcurrent condition was happening on the SoCFPGA Cyclone5 devkit, thus
USB was not working on the devkit. This patch fixes that problem.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Fix the BOOTCFG value for eMMC in the same way as commit
214c3f0f99
[imx: MX6DQ{P}/DL:SABRESD Fix bmode eMMC failure]
did for sabresd.
Signed-off-by: Soeren Moch <smoch@web.de>
Move to booting a zImage kernel by default to align with the other
i.MX boards.
While at it, adjust the fdt_addr so that we can boot a standard
mainline kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
During very early boot-ROM execution the pinmux
configuration isi in Hi-Z state. If pull-up is enabled
on GPIO pad's there will be a short period of toggle
from high to low on the IO when GPIO is set low during
boot. To avoid this glitch, disable pull-up configuration
in GPIO pinmux.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
In case when usb_composite_register() failed once (for whatever reason),
it will fail further even if all conditions are correct. Example:
=> fastboot 2
Invalid Controller Index
couldn't find an available UDC
g_dnl_register: failed!, error: -19
exit not allowed from main input shell.
=> fastboot 0
g_dnl_register: failed!, error: -22
exit not allowed from main input shell.
Despite that 0 is correct index for USB controller, "fastboot 0" command
will fail, because "composite" structure wasn't cleared properly on
previous fail (on "fastboot 2" command).
This patch fixes that erroneous behavior, allowing us to use composite
even after previous failure.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
"fastboot oem format" command reuses "gpt write" command, which in turn
requires correct partitions defined in $partitions variable. This patch
adds such definition of Android partitions for DRA7XX EVM board.
By default $partitions variable contains Linux partition table. In order
to prepare Android environment one can run next commands from U-Boot
shell:
=> env set partitions $partitions_android
=> env save
After those operations one can go to fastboot mode and perform
"fastboot oem format" to create Android partition table.
While at it, enable CONFIG_RANDOM_UUID to spare user from providing
UUIDs for each partition manually.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces some minor cleanups, regarding aspects such as board name, code
and headers organization as well as deprecated and missing config options.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are a number of AMCC platforms which are close to, or with some
toolchains exceeding, the size constraints. Disable CONFIG_SYS_LONGHELP
to get us room to build with again.
Signed-off-by: Tom Rini <trini@konsulko.com>
Copy these from Linux v4.5-rc6 tag.
This is needed so that we can keep up with newer gcc versions. Note
that we don't have the uapi/ hierarchy from the kernel so continue to
use <linux/types.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
The UniPhier SoC family has not supported ARMv8 yet, but these would
cause warnings if they were compiled with a 64bit compiler. Before
adding the ARMv8 support really, fix them now.
Because UniPhier SoCs do not support Large Physical Address Extension,
casting "phys_addr_t" into "unsigned long" would carry the address
as is.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Before adding ARMv8 support, this commit refactors the directory
structure. Move ARMv7 specific files to arch/arm/mach-uniphier/arm32
to avoid a mess by mixture of ARMv7 and ARMv8 code. Also move the
"select CPU_V7" to the lower-level menu because we will have to
select ARM64 instead of CPU_V7 for ARMv8 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit d9a3bec682.
While this is a correct change to do long term it unfortunately breaks a
number of platforms that are using pdata and not named struct members so
they are getting all of their data after 'base' incorrect.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Due to the company's awful projecting, PH1-LD10 and PH1-sLD11 have
been renamed to PH1-LD20 and PH1-LD11, respectively.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The chains of "depends on <SoC_name>" in the current Kconfig is
clumsy. The idea here is to allow users to choose a SoC group first
(SoC group consists of some SoCs that can coexist in one binary).
Then, allow to enable/disable each SoC support in the selected SoC
group. This makes the Kconfig menu clearer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PH1-Pro5 support and ProXstream2/PH1-LD6b support can coexist in one
image and there is bit more room in SPL to accommodate all of them.
Merge uniphier_pro5_defconfig into uniphier_pxs2_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These macros are no longer used. These base addresses are
SoC-dependent, so they should not be placed in the header.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, DRAM size is converted twice:
size in byte -> size in Gbit -> enum
Optimize the code by converting the "size in byte" into enum directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Simon Glass
Stuart Longland
Tom Rini
Fabio Estevam
Marek Vasut
Lokesh Vutla
Anand Moon
Chris Zhong
FUKAUMI Naoki
Lin Huang
Daniel Schwierzeck
Matthias Schiffer
Stephen Warren
Alexander Graf
Stanislav Galabov
Derald D. Woods
Masahiro Yamada
Dinh Nguyen
Soeren Moch
Bhuvanchandra DV
Sam Protsenko
Paul Kocialkowski
Yuichiro Goto