It's RISC-V that is the official name, not RISCV.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add DM support to the SH QSPI driver while retaining non-DM support.
The later is required as this driver is used in SPL which has a size
limitation of 16 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
[jagan: use proper commit head]
Reviewed-by: Jagan Teki <jagan@openedev.com>
Convert fsl_qspi.c to complete DM mode.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Tested-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Tested-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add code to reset all reset signals as in SPI DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Release reset when _remove().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The 'mtdparts' command is not needed anymore. While the environment
variable is still valid (and useful, along with the 'mtdids' one), the
command has been replaced by 'mtd' which is much more close to the MTD
stack and do not add its own specific glue.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
UBI should not mess with MTD partitions, now that the partitions are
handled in a clean way, clean the ubi command and avoid using this
uneeded extra-glue to reference the devices.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
There should not be a 'nand' command, a 'sf' command and certainly not
a new 'spi-nand' command. Write a 'mtd' command instead to manage all
MTD devices/partitions at once. This should be the preferred way to
access any MTD device.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Instead of collecting partitions in a flat list, create a hierarchy
within the mtd_info structure: use a partitions list to keep track of
the partitions of an MTD device (which might be itself a partition of
another MTD device), a pointer to the parent device (NULL when the MTD
device is the root one, not a partition).
By also saving directly in mtd_info the offset of the partition, we
can get rid of the mtd_part structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Using an MTD device (resp. partition) name in mtdparts is simple and
straightforward. However, for a long time already, another name was
given in mtdparts to indicate a device (resp. partition) so the
"mtdids" environment variable was created to do the match.
Let's create a function that, from an MTD device (resp. partition)
name, search for the equivalent name in the "mtdparts" environment
variable thanks to the "mtdids" string.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The current parser is very specific to U-Boot mtdparts implementation.
It does not use MTD structures like mtd_info and mtd_partition. Copy
and adapt the current parser in drivers/mtd/mtd-uclass.c (to not break
the current use of mtdparts.c itself) and write some kind of a wrapper
around the current implementation to allow other commands to benefit
from this parsing in a user-friendly way.
This new function will allocate an mtd_partition array for each
successful call. This array must be freed after use by the caller.
The given 'mtdparts' buffer pointer will be moved forward to the next
MTD device (if any, it will point towards a '\0' character otherwise).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The user might want to trigger the probe of any MTD device, export these
functions so they can be called from a command source file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
include/mtd.h might be included by files even if CONFIG_DM is not
enabled. In this case, the call to dev_get_uclass_priv() would trigger
a build error. Because this helper has no user, let's drop it off.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The btrfs implementation passes cache-unaligned buffers into the
block layer, which triggers cache alignment problems down in the
block device drivers. Align the buffers to prevent this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Behun <marek.behun@nic.cz>
MSM uses the chipidea controller IP, however it requires
to reinit the phy after controller reset. in EHCI mode there's a
dedicated callback for it.
In device mode however there's no such callback.
Add implementaion of ci_init_after_reset() to implement the above
requirement in case CI_UDC driver is used.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
MSM variant of Chipidea must reinitalize the phy
after controller reset.
Introduce ci_init_after_reset() weak function that
can be used to achieve the above init.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The serial# environment variable needs to be
defined so it will be used by fastboot as serial
for the endpoint descriptor.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
platdata_auto_alloc_size was not initialized in structure.
Caused null pointer dereference when configuring device as
gadget.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Since commit 7b3b74d321 ("serial: serial_stm32: Enable overrun")
on STM32F7xx based boards, the first lines of serial output are
missing during boot (we no more see the U-Boot release version,
board model and DRAM size).
By enabling the uart FIFO on STM32F7, the complete U-boot log
can be sent correctly.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
[trini: Manually apply, rework whitespace]
Signed-off-by: Tom Rini <trini@konsulko.com>
The escape sequence '\#' does not work for the latest GNU Make from
the git tree.
Replace it with $(pound) as Linux did.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[ commit 9564a8cf422d7b58f6e857e3546d346fa970191e in Linux ]
I tried building using a freshly built Make (4.2.1-69-g8a731d1), but
already the objtool build broke with
orc_dump.c: In function ‘orc_dump’:
orc_dump.c:106:2: error: ‘elf_getshnum’ is deprecated [-Werror=deprecated-declarations]
if (elf_getshdrnum(elf, &nr_sections)) {
Turns out that with that new Make, the backslash was not removed, so cpp
didn't see a #include directive, grep found nothing, and
-DLIBELF_USE_DEPRECATED was wrongly put in CFLAGS.
Now, that new Make behaviour is documented in their NEWS file:
* WARNING: Backward-incompatibility!
Number signs (#) appearing inside a macro reference or function invocation
no longer introduce comments and should not be escaped with backslashes:
thus a call such as:
foo := $(shell echo '#')
is legal. Previously the number sign needed to be escaped, for example:
foo := $(shell echo '\#')
Now this latter will resolve to "\#". If you want to write makefiles
portable to both versions, assign the number sign to a variable:
C := \#
foo := $(shell echo '$C')
This was claimed to be fixed in 3.81, but wasn't, for some reason.
To detect this change search for 'nocomment' in the .FEATURES variable.
This also fixes up the two make-cmd instances to replace # with $(pound)
rather than with \#. There might very well be other places that need
similar fixup in preparation for whatever future Make release contains
the above change, but at least this builds an x86_64 defconfig with the
new make.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197847
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If we fail to find the MMC boot device, report the number of the one
we were looking for in the error to aid diagnosis.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The Arm Versatile Express and Juno development boards contain an
OSC clock generator that can be accessed through the Versatile
Express config bus. The generators are quite often being controlled
by some MCU and the config bus offers a uniform way of exposing them.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a test which verifies that all subnodes under "/firmware"
nodes are scanned.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added 'imply FIRMWARE' to sandbox Kconfig to fix test failures, fixed
ordering of lines in arch/sandbox/dts/test.dts and test/dm/Makefile,
updated #if condition in drivers/firmware/firmware-uclass.c:
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no prompt string for FIRMWARE config. Without this,
FIRMWARE config cannot be enabled through menuconfing or
config file. Fix this by adding prompt summary.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Something has changed in the last several month such that when buildman
builds U-Boot incrementally and a new CONFIG option has been added to the
Kconfig, the build hanges waiting for input:
Test new config (NEW_CONFIG) [N/y/?] (NEW)
Since binamn does not connect the build's stdin to anything this waits on
stdin to the build thread, which never comes. Eventually I suspect all the
threads end up in this state and the build does not progress.
Fix this by passing /dev/null as input to the build. That way, if there is
a new CONFIG, the build will stop (and fail):
Test new config (NEW_CONFIG) [N/y/?] (NEW)
Error in reading or end of file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove duplicated inclusion of dm/ofnode.h
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Drop period at end of commit subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
The comment references a structure name that doesn't exist. Use
the name of the actual uclass.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Drop period at end of commit subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
Converts fdtdec_setup_memory_banksize() to use ofnode functions instead.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Add trivial implementation of the clk dump in case DM is enabled.
This implementation just iterates over all the clock registered
with the CLK uclass and prints their rate.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Bin Meng
Tom Rini
Marek Vasut
Ashish Kumar
Ley Foon Tan
Miquel Raynal
Eugen Hristev
Marek Vasut
Ramon Fried
Patrice Chotard
Neil Stainton
Masahiro Yamada
Rasmus Villemoes
Alex Kiernan
Liviu Dudau
Rajan Vaja
Simon Glass
Jens Wiklander
Mario Six