cpu/mpc8260/cpu.c used to use do_fixup_by_path_u32() to update the
clock frequencies in the device tree, using a CPU path
"/cpus/OF_CPU", with OF_CPU beind defined in the board config file.
However, this does not work when one board config file (here:
MPC8260ADS.h) is intended to be used for several diffrent CPUs and
therefor contains a generic definition like "cpu@0", as the device
trees that will then be loaded will contain specific names like
"PowerPC,8272@0".
We switch to using do_fixup_by_prop_u32() instead, so we can search
for device_type="cpu", as it is done in other architectures, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
AFEB9260 uses PA10, PA11 for ETX2 and ETX3.
Also, due to extarnal pull-up on IRQ line, Micrel PHY ID is 1 after reset sequence,
not 0.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
When the clock functions were changed to use cached values (and thereby
avoiding expensive math functions), early serial debug broke because the
baud programming is called before external memory is available.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When dropping jump block support, the assumption was that all bootroms
supported entry point redirection via the EVT1 register. Unfortunately,
this turned out to be incorrect for the oldest Blackfin parts (BF533-0.2
and older and BF561). No one really noticed earlier because these parts
usually are booted by bypassing the bootrom entirely, and older BF533
parts are not supported at all (too many anomalies).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we recurse through serial_putc() rather than bang on the UART
transmit register directly to avoid hardware overflows when using \n.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
lowlevel_init.S is not used any more so remove it.
As consequence, we also don't have to generate u-boot.lds
but can use a static version as before.
This also fixes the out-of-tree build problem introduced
with commit f0a2c7b4 "at91: add support for the PM9263 board"
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Let CONFIG_SYS_HZ to have value of 1000 effectively fixing all users of
get_timer.
Changes since original version:
* Set PTV=2 (divisor 8) for boards using 12MHz timer clock source to
improve timer resolution.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
The function display_board_info() displays incorrect
silicon revision - based on the return value from
function get_cpu_rev().
This patch fixes the problem.
Signed-off-by: Sanjeev Premi <premi@ti.com>
The board-types defined in struct omap3_sysinfo seem to be
unused. The function display_board_info() is passed
board type as an argument; which is ignored.
This patch removes all uses of board-type, related definitions
and functions.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Use the functions print_cpuinfo() and checkboard() to
display the cpu and board specific information.
These functions reuse content from the existing function
display_board_info() - which has been removed.
Also, updated the existig OMAP3 configurations to
define:
- CONFIG_DISPLAY_CPUINFO
- CONFIG_DISPLAY_BOARDINFO
Signed-off-by: Sanjeev Premi <premi@ti.com>
__asm__ follows gcc's documented syntax and is generally more common
than __asm. This change is only asthetic and should not affect
functionality.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute. This change is only asthetic and should not
affect functionality.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
if using CONFIG_BOOTCOUNT_LIMIT feature on a MPC8360 CPU
in the muram-data node, the reg entry needs to be updated.
This is done in fdt_fixup_muram(), but we should use
the compatible "fsl,qe-muram-data" for searching the
node instead of searching the muram-data node with
an absolute path.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The timer has been rewrote with a precision at ~0,18%
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Eric BENARD <ebenard@free.fr>
The PM9263 board is based on the AT91SAM9263-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This additional text in the bootup log helps to see if the board is
configured for NAND-booting. Especially helpful for boards that can
boot from NOR and NAND (e.g. most of the AMCC eval boards).
Signed-off-by: Stefan Roese <sr@denx.de>
There is no code change here, just new comments, but this keeps me from
having to do another audit from scratch in the future.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
DESCRIPTION:
The column address width settings for banks 2 and 3 are misconnected in
the SDRAM controller. Accesses to bank 2 will result in an error if the
Column Address Width for bank 3 (EB3CAW ) is not set to be the same as
that of bank 2.
WORKAROUND:
If using bank 2, make sure that banks 2 and 3 have the same column address
width settings in the EBIU_SDBCTL register. This must be the case
regardless of whether or not bank 3 is enabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
DESCRIPTION:
If the DF bit is set prior to a hardware reset, the PLL will continue to
divide CLKIN by 2 after the hardware reset, but the DF bit itself will be
cleared in the PLL_CTL register.
WORKAROUND:
Reprogram the PLL with DF cleared if the desire is to not divide CLKIN by
2 after reset.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
DESCRIPTION:
The Boot ROM is executed at power up/reset and changes the value of the
SICA_IWR registers from their default reset value of 0xFFFF, but does not
restore them.
WORKAROUND:
User code should not rely on the default value of these registers. Set
the desired values explicitly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The previous code waited 1000us before checking i2c
status. Measurement shows i2c is usually ready in
under 50us. Change the polling interval to 15us,
loop 6,667 times to keep the polling timeout constant
at 100ms.
Fixes this compile error:
board.c: In function 'do_switch_ecc':
board.c:339: error: 'cmd_tbl_t' has no member named 'help'
make[1]: *** [board.o] Error 1
make[1]: Leaving directory `/db/psp_git/users/a0756819/u-boot/cpu/arm_cortexa8/omap3'
make: *** [cpu/arm_cortexa8/omap3/libomap3.a] Error 2
This is due to the fact that current command uses long
help for the usage print even if the CONFIG_SYS_LONGHELP
is not enabled. (Thanks Jean-Christophe for explanation).
Signed-off-by: Sanjeev Premi <premi@ti.com>
Move machine specific code to smdk6400.
Some board use OneNAND instead of NAND.
Some register MP0_CS_CFG[5:0] are controled by both h/w and s/w.
So it's better to use macro instead of hard-coded value.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Update the rm9200 reset sequence to try executing a board-specific reset
function and move specific board reset to board.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
introduce serial_exit for this purpose. Use it only when the rm9200
serial driver is active
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507
with
- NOR (cfi driver)
- DataFlash
- USB OHCI
- Net
- I2C (hard)
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
When testing a u-boot binary that hasn't been booted from the bootrom, we
have to make sure the bootstruct structure has sane storage space. If we
don't, the initcode will crash when it tries to dereference an invalid
pointer.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Match determine_mp_bootpg() that was added for 86xx. We need this to
address a bug introduced in v2009.03 with 86xx MP booting. We have to
make sure to reserve the region of memory used for the MP bootpg() so
other u-boot code doesn't use it.
Also added a comment about how cpu_reset() is dealing w/an errata on
early 85xx MP HW.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx
* Introduce determine_mp_bootpg() helper. We'll need this to address a
bug introduced in v2009.03 with 86xx MP booting. We have to make sure
to reserve the region of memory used for the MP bootpg() so other
u-boot code doesn't use it.
* Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to
allow cmd_mp.c to build and work. In the future we should look at
implementing all these functions. This could be common w/85xx if we
use spin tables on 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a workaround for MPC8569 CPU Errata, which needs to set Bit 13 of
LBCR in 4K bootpage. We setup a temp TLB for eLBC controller in bootpage,
then invalidate it after LBCR bit 13 is set.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- support mirrored DIMMs, not support register DIMMs
- test passed on P2020DS board with MT9JSF12872AY-1G1D1
- test passed on MPC8569MDS board with MT8JSF12864HY-1G1D1
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Travis Wheatley <travis.wheatley@freescale.com>
1. wr_lat
UM said the total write latency for DDR2 is equal to
WR_LAT + ADD_LAT, the write latency is CL + ADD_LAT - 1.
so, the WR_LAT = CL - 1;
2. rd_to_pre
we missed to add the ADD_LAT for DDR2 case.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Wolfgang Denk
Sergey Lapin
Mike Frysinger
Jean-Christophe PLAGNIOL-VILLARD
Manikandan Pillai
Daniel Gorsulowski
Ladislav Michl
Sanjeev Premi
Peter Tyser
Heiko Schocher
Ilko Iliev
Stefan Roese
Jon Smirl
Kyungmin Park
Scott Wood
Ulf Samuelsson
Kumar Gala
Haiying Wang
Dave Liu