This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories. All refernces to the former locations are updated to
the current locations. For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.
Signed-off-by: Tom Rini <trini@konsulko.com>
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
This information is already available under vcores->volts.efuse.reg.
There is no reason for duplicating the information since AVS Class 0
definitions are common for OMAP5 and DRA7 and defined with
STD_FUSE_OPP_* macros. This allows a central location of defining
the ABB and voltage definitions especially since they are reused.
This also makes it simpler to prevent mistakes involved when changing
the boot OPP for the device.
Signed-off-by: Nishanth Menon <nm@ti.com>
This introduces omap5 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enabled clocks for the second dwc3 controller and second USB PHY present in
DRA7.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.
Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.
NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
On AM57xx evm I2C5 is used to detect the LCD board by reading the
EEPROM present on the bus.
Enable i2c5 clocks to help that.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.
IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch populates serial number environment variable from
die_id_0 and die_id_1 register values for DRA7xx boards.
The function is added in omap common code so that this can be re-used.
Serial# environment variable will be useful to show correct
information in "fastboot devices" commands.
Ref:
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=a6bcaaf67f6e4bcd97808f53d0ceb4b0c04d583c
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enabled clocks for dwc3 controller and USB PHY present in DRA7.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
some boards might want to use USB1 for host,
without fiddling those registers it'll be
impossible.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
commit 194dd74ad9
(DRA7: add ABB setup for MPU voltage domain)
Made an offset typo error by using 0x4A003B24 as the efuse offset
for OPP_NOM. As per TI documentation, 0x4A003B24 is for OPP_OD, and
0x4A003B20 is for OPP_NOM. Fix the same.
Reported-by: Praveen Rao <prao@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Patch adds modification to shared omap5 abb_setup() function, and
proper registers definitions needed for ABB setup sequence. ABB is
initialized for MPU voltage domain at OPP_NOM.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.
The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Writing magic bits into LDO SRAM was suggested only for OMAP5432
ES1.0. Now these are no longer applicable. Moreover these bits should
not be overwritten as they are loaded from EFUSE. So avoid
writing into these registers.
Boot tested on OMAP5432 ES2.0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Locking DPLL_GMAC
[mugunthanvnm@ti.com:Configure only if CPSW is selected]
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
auxclk0 and auxclk1 are utilized on some OMAP5 boards.
Define the infrastructure needed for accessing them
without using magic numbers.
Also remove unrelated TPS62361 defines from clocks.h
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
DRA7 EVM board has the below configuration. Adding the
settings for the same here.
2Gb_1_35V_DDR3L part * 2 on EMIF1
2Gb_1_35V_DDR3L part * 4 on EMIF2
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The newly introduced function setup_warmreset_time(), called
from within prcm_init(), tries to write to the prm_rsttime
OMAP5 register. The struct member holding this register's
address is however initialized for OMAP5 ES2.0 only. On ES1.0
devices this uninitialized value causes a second (warm) reset
at startup.
Add .prm_rsttime address init to the ES1.0 struct.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Tom Rini <trini@ti.com>
Patch adds a call of abb_setup() function, and proper registers
definitions needed for ABB setup sequence. ABB is initialized
for MPU voltage domain.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.
There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.
In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Control module register addresses are changed from OMAP5
to DRA7XX socs.
So adding the necessary changes for the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
PRCM register addresses are changed from OMAP5 ES2.0 to DRA7XX.
So adding the necessary register changes for DRA7XX socs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
After power-up SRCOMP cells are by-passed by default in OMAP5.
Software has to enable these SRCOMP sells.
For ES2: All 5 SRCOMP cells needs to be enabled.
For ES1: Only 4 SRCOMP cells in core power domain are enabled.
The 1 in wkup domain is not enabled because smart i/os
of wkup domain work with default compensation code.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Tom Rini <trini@ti.com>
PRCM register addresses are changed from ES1.0 to ES2.0 due to
PER power domain getting moved to CORE power domain.
So adding the nessecary register changes for the same.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Tom Rini <trini@ti.com>
A seperate omap_sys_ctrl_regs structure is defined for
omap4 & 5. If there is any change in control module for
any of the ES versions, a new structure needs to be created.
In order to remove this dependency, making the register
structure generic for all the omap4+ boards.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
The current PRCM structure prototype directly matches the hardware
register layout. So there is a need to change this for every new silicon
revision which has register space changes.
Avoiding this by making the prototye generic and populating the register
addresses seperately for all Socs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tom Rini
Roger Quadros
Nishanth Menon
Paul Kocialkowski
Kishon Vijay Abraham I
Vignesh R
Lokesh Vutla
Dileep Katta
Felipe Balbi
Dan Murphy
Wolfgang Denk
Matt Porter
Mugunthan V N
Lubomir Popov
Sricharan R
Andrii Tseglytskyi