Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
This patch solves a problem with USB hanging under higher load on a
i.MX31 board. It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.
The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.
Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.
Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
Commit 3ed1607 "USB: sync Queue Element Transfer Descriptor against
EHCI spec" added an "__attribute__ ((aligned (32)))" to the
declaration of struct qTD, as used for example in the Linux kernel as
well.
However, it turns out that this attribute causes errors in "usb start"
(like "ERROR: NOT USB_CONFIG_DESC 7b" and similar). Drop the attribute
again.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
It is useful to know the EHCI-PCI hccr, hcor and hc_lenght to make sure it was
successfully registered, and at the correct location.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch solves a problem with USB hanging under higher load on a
i.MX31 board. It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.
The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.
Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.
Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
Appendix B "EHCI 64-Bit Data Structures" of the "Enhanced Host
Controller Interface Specification for Universal Serial Bus" (Rev.
1.0, March 12, 2002) defines additional fields which were missing in
U-Boot's struct qTD; as these are also present in recent versions of
struct ehci_qtd in the Linux kernel, we add them here, too.
This fixes some nasty memory corruption problems.
Reported-by: Dan Lykowski <lykowdk@gmail.com>
See http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/76942
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Sometimes a usb tree is not popolated after a system reset.
It seems a delay is required after setting the USB ports
for the MX.31 before resetting the ehci controller.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This fixes TIMEOUT with my Kingston 32GB USB3.0 flashdrive, which I experienced
on my PXA270 (USB 1.1) Vpac270 board.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This avoids a build warning that you see if anyone in the
header chain has included io.h (which is coming shortly). The previous
code redefined readl/writel; this patch renames it to be specific to
ohci. The defines are also moved from ohci-hcd.c to ohci.h.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.
Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
ehci_submit_async() doesn't really zero out the QH transfer overlay (as the EHCI
specification suggests) which leads to the controller seeing the "token" field
as the previous call has left it, i.e.:
- if a timeout occured on the previous call (Active bit left as 1), controller
incorrectly tries to complete a previous transaction on a newly programmed
endpoint;
- if a halt occured on the previous call (Halted bit set to 1), controller just
ignores the newly programmed TD(s) and the function then keeps returning error
ad infinitum.
This turned out to be caused by the wrong orger of the arguments to the memset()
call in ehci_alloc(), so the allocated TDs weren't cleared either.
While at it, stop needlessly initializing the alternate next TD pointer in the
QH transfer overlay...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Add NEC EHCI controller to the list of the supported devices.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
drivers/usb/host/ehci-pci.c | 1 +
1 file changed, 1 insertion(+)
Commit b416191a14 (Fix EHCI port reset.) didn't
move the code that checked for successful clearing of the port reset bit from
ehci_submit_root(), relying on wait_ms() call instead. The mentioned code also
erroneously reported port reset state when the reset was already completed.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
USB devices on the 2nd port are not detected and I get the following message:
The request port(1) is not configured
That's with default CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS value of 2. 'req->index'
is 1-based, so the comparison in ehci_submit_root() can't be correct.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
On little endian machines, EHCI root hub's USB revision is reported as 0.2 --
cpu_to_le16() was missed in the initializer for the 'bcdUSB' descriptor field.
The same should be done for the 'bcdDevice' field.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
This patch is part of migrating the AT91 support towards
using C struct for all SOC access.
It removes one more CONFIG_AT91_LEGACY warning.
at91_pmc.h needs cleanup after migration of the drivers
has been done.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
* add's a warning to all files, which need update to new SoC access
* convert common files in cpu/../at91 and a lot of drivers to use
c stucture SoC access
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
In USB ehci driver, the port reset is not terminated. EHCI spec says "A host
controller must terminate the reset and stabilize the state of the port within
2 milliseconds". Without termination, a port stays at reset state. This is
observed on ppc4xx(sequoia) boards.
Signed-off-by: Chris Zhang <chris@seamicro.com>
The header files usb.h and usbdescriptors.h have the same nameed
structure definitions for
usb_config_descriptor
usb_interface_descriptor
usb_endpoint_descriptor
usb_device_descriptor
usb_string_descriptor
These are out right duplicates in usb.h
usb_device_descriptor
usb_string_descriptor
This one has extra unused elements
usb_endpoint_descriptor
unsigned char bRefresh
unsigned char bSynchAddress;
These in usb.h have extra elements at the end of the usb 2.0
specified descriptor and are used.
usb_config_descriptor
usb_interface_descriptor
The change is to consolidate the definition of the descriptors
to usbdescriptors.h. The dublicates in usb.h are removed.
The extra element structure will have their name shorted by
removing the '_descriptor' suffix.
So
usb_config_descriptor -> usb_config
usb_interface_descriptor -> usb_interface
For these, the common descriptor elements are accessed now
by an element 'desc'.
As an example
- if (iface->bInterfaceClass != USB_CLASS_HUB)
+ if (iface->desc.bInterfaceClass != USB_CLASS_HUB)
This has been compile tested on MAKEALL arm, ppc and mips.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change is cheked in Linux source and fix found to be in sync.
This patch is tested for USB host interface on Kirkwood based
Sheevaplug platform (ARM little endian board)
Risk: the impact of this patch is not validated on big endian board.
This need to be checked...
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
ehci-hcd.c: In function 'ehci_submit_root':
ehci-hcd.c:719: warning: value computed is not used
ehci-hcd.c:748: warning: value computed is not used
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch fixes the access to the 'ehci' struct elements which should
have been taken care off in 4ef01010aa
Sorry about that.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch reorganizes/reworks the USB support for mpc83xx
as under:-
* Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to
cpu/mpx83xx/cpu_init.c
* Board specific usb_phy_type is read from the environment
* Adds USB EHCI specific structure in include/usb/ehci-fsl.h
* Copyrights revamped in most of the following files
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch moves 8xxx-specifc USB #defines from
drivers/usb/host/ehci-fsl.h to include/usb.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
To prepare for the 85xx USB support, which requires interface enablement
only once in (specified) order, no different than instructions for
enabling the interface under 83xx. It is unknown why the original author
enabled the interface twice (checked for references in errata, etc).
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch corrects the missing PLLB initialization in usb_cpu_init()
for AT91SAM9261.
Because of the missing PLLB initialization, the USB support for all
AT91SAM9261 based boards will work only if the PLLB is configured by a
precedent bootloader.
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute. This change is only asthetic and should not
affect functionality.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
move to linux usb driver organisation
as following
drivers/usb/gadget
drivers/usb/host
drivers/usb/musb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Sebastien Carlier
Wolfgang Denk
Florian Fainelli
Damien Dusha
Stefano Babic
Marek Vasut
Becky Bruce
Sergey Matyukevich
Sergei Shtylyov
Peter Tyser
Matthias Fuchs
Jens Scharsig
Chris Zhang
Tom Rix
kevin.morfitt@fearnside-systems.co.uk
Minkyu Kang
Prafulla Wadaskar
Kumar Gala
Vivek Mahajan
RONETIX - Ilko Iliev
Detlev Zundel
Jean-Christophe PLAGNIOL-VILLARD