vbus-usable may not get set if power is provided through both the power barrel
connector and external 5v is also present on the otg connector, at least on
boards where vbus is also controlled through the axp221-pmic.
One way to reproduce this is to bootup an Ippo-q8h board with a usb-host
cable plugged into the otg (so that it will get powered), then unplug the
usb-host cable and plug in a charger, and then do "reset" on the u-boot
console, vbus-usable will then report 0, leading to uboot trying to provide
power to the otg port even though external 5v is present, this commit fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When u-boot boots the board may be powering vbus, we turn off vbus in
sunxi_usbc_request_resources, if we are too quick with reading vusb-detect
after this we may see a residual charge and assume we've an external vusb
connected even though we do not. So when we see an external vusb wait a bit
and try again.
Without this when dealing with a pmic controller vbus and doing "reset" on
the u-boot console the musb host will only init once every other boot, because
the other boot it thinks an external vbus is present, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On boards which use the pmic to enable/disable vbus on the otg port, the
vbus value is not reset to 0 on reset, as reset only resets the SoC and not
the pmic, so explicitly set vbus to 0 on init (request_resources) by moving
the gpio_direction_output call into request_resources.
For consistency also move the gpio_direction_input call for vbus-detect into
request_resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Yones Toptech BD1078 is an A20 based 10" tablet with a 1024x600 lcd screen,
volume up/down and back buttons, headphones jack, mini hdmi, micro usb (otg),
micro usb (host), external micro-sd slot and a separate internal micro-sd slot.
Also see: http://linux-sunxi.org/Yones_Toptech_BD1078
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Sunxi platforms have different possible mmc pin mux setups (except for mmc0),
which are different across platforms.
This lets users configure which is used through the CONFIG_MMC*_PINS Kconfig
options. This is especially relevant when a second (in addition to mmc0) port
is used and CONFIG_MMC_SUNXI_SLOT_EXTRA is enabled.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is no need to define one value per
pin: one value per hardware feature per port is sufficient, avoids duplication
and makes everything easier to understand.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Ainol AW1 is an A20 based tablet with a 800x480 lcd screen, sdio wifi,
volume up/down and home buttons, micro-sd slot, micro usb (otg), headphones
connector and a SPCI modem connector.
Also see: http://linux-sunxi.org/Ainol_AW1
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
VBUS detection could be needed not only by the musb code (to prevent host mode),
but also by e.g. gadget drivers to start only when a cable is connected.
In addition, this allows more flexibility in vbus detection, as it could easily
be extended to other USBC indexes. Eventually, this would help making musb
support independent from a hardcoded USB controller index (0).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
VBUS detection and enable is now be used with virtual AXP GPIOs, so all the USB
code has to use GPIO in every case and let sunxi_gpio do the heavy lifting.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be used aside usual GPIO functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Mixtile LOFT-Q is an A31 based board with 2G RAM, 8G EMMC, sdio wifi,
1Gbit ethernet, HDMI display, toslink audio plug, 4 USB2.0 port, external
USB2SATA connector, sd card plug, 3x60 external fpic expansion connector,
NXP JN5168 zigbee gw, remote support.
Also see http://focalcrest.com/en/pc.html#pro02
Signed-off-by: Han Pengfei <pengphei@sina.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The "fastboot reboot-bootloader" command is defined to
re-enter into fastboot mode after rebooting into
bootloader. This command is usually used after updating
bootloader via fastboot.
This commit implements only a generic side of the
command - setting of the reset flag and then resetting.
Setting of the reset flag is implemented using __weak
fb_set_reboot_flag() function. The actual setting and
checking of the reset flag should be implemented by
a boot script and/or board/SoC specific code.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm28155_ap board]
Implement an alias name check for devices where GPT limitations prevent
user-friendly partition names such as "boot", "system" and "cache". Or,
where the actual partition name doesn't match a standard partition name
used commonly with fastboot.
To set an alias, add an environment setting as follows:
fastboot_partition_alias_<alias partition name>=<actual partition name>
Example: fastboot_partition_alias_boot=LNX
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>
Cc: Steve Rae <srae@broadcom.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
trigger watchdog before calling usb_gadget_handle_interrupts()
This prevents board resets when calling dfu command on boards
which have a watchdog.
Signed-off-by: Heiko Schocher <hs@denx.de>
[ Reedition by Lukasz Majewski <l.majewski@samsung.com> to apply to
v2014.04 release ]
USB Mass Storage is the standard name, so let's use it here.
Suggested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
For u-boot dwc3 driver the scatter gather list support has been removed
from original linux code. It is correct, since we try to send one request
at a time.
However, the cleanup left spurious break, which caused early exit from
loop at dwc3_cleanup_done_reqs() function. As a result the dwc3_gadget_giveback()
wasn't called and caused USB Mass Storage to hang.
This commit removes this problem and refactor the code to remove superfluous
do { } while(1) loop.
Test HW: Odroid XU3 (with ./test/ums/ums_gadget_test.sh)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Commit "drivers/dwc3: add a workaround for too small OUT requests"
sets max packet for OUT requests when transfer is smaller.
Until this change the default maxpacket for non EP0 EPs was 1024. This is
too much, since UMS LBA size is 512B
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
It turned out that current dwc3 gadget code is preparing multiple TRBs
for a transfer. Unfortunately, when multiple requests are in the same
queue, only for the last one the LST (last) ctrl bit is set.
Due to that dwc3 HW executes all TRBs up till the one marked as last.
Unfortunately, UMS requires call of ->complete callback after any send TRB.
This is the reason for "hangs" in executing UMS.
This code simplifies this situation and set each TRB's ctrl field bit to be
last (LST bit).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
There is no point in calling dwc3_thread_interrupt() if no event is
pending. There is also no point in flushing event cache in EVERY loop
iteration.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch adds code to select standard, commonly used usb endpoint
configuration (ep1in-bulk, ep2out-bulk, ep3in-int) to dwc3 driver. This
ensures compatibility with old userspace and windows drivers, which
expects hardcoded endpoint numbers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
DWC3 hangs on OUT requests smaller than maxpacket size,
so HACK the request length to be at least equal to maxpacket size.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This commit makes the dwc3_set_mode() as static, to prevent collisions.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
The BIT() macro is used only in those places, so it is reasonable to
replace it by a constant value.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
DWC3 UDC driver requires presence of .reset callback in a composite driver.
This setting is similar to the one nowadays present in linux kernel.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
This patch invokes board-specific USB cleanup (board_usb_cleanup)
function in the mass storage gadget
Signed-off-by: Inha Song <ideal.song@samsung.com>
Since we support multiple dwc3 controllers to be existent at the same
time, in order to handle the interrupts of a particular dwc3 controller
usb_gadget_handle_interrutps should take controller index as an
argument.
Hence the API of usb_gadget_handle_interrupts is modified to take
controller index as an argument and made the corresponding changes to all
the usb_gadget_handle_interrupts calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in am43xx board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in dra7xx board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Invoked board_usb_cleanup for cleaning up initialized USB. It
will be invoked if the user enterts ctrl-C.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Taken from linux kernel with commit
commit 765f5b830e547229bb752e7b232ee83e2b3d49d5
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date: Thu Jun 23 14:26:11 2011 +0200
usb: gadget: defer setting maxpacket till ->setup()
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Now that the entire dwc3 driver is adapted to compile with uboot build,
modify the Makefiles so that the dwc3 driver can be built.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
dwc3 can do only max packet aligned transfers. So in case request length
is not max packet aligned and is bigger than DWC3_EP0_BOUNCE_SIZE
two chained TRBs is required to handle the transfer.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
No functional change. Modified few things so that there are no
code duplication while implementing chained TRB.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Paul Kocialkowski
Hans de Goede
Han Pengfei
Alexey Firago
Michael Scott
Heiko Schocher
Fabio Estevam
Marek Szyprowski
Lukasz Majewski
Joonyoung Shim
Inha Song
Kishon Vijay Abraham I