Move all the gpio definitions to driver file as
there is no use of them in other files.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove non driver model support as it moved
to driver model. Dont need non driver model
anymore.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable DM GPIO and ZYNQ GPIO using kconfig instead of the board
config file.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To make the usage of this function more flexible, lets add the CRC start
value as parameter to this function. This way it can be used by other
functions requiring different start values than 0 as well.
For non-zero CRC start values to work, I've reworked the function a bit.
The new implementation is copied from the Linux version in
drivers/i2c/i2c-core.c / i2c_smbus_pec(). Which supports non-zero
CRC stating values.
I've double-checked that the results for zero starting values are
identical to the results from the original version of this function.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a call to flush_dcache_range() to bootcount_store() to
make sure, that the bootcounter data (including the patterns) is
written to memory. Without this, platforms with dcache enabled may not
have the bootcounter updated upon reset.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
After writing data to flash space, next instruction is checking if flash
controller is busy writing to the flash memory. Memory barrier is required here
to avoid transaction re-ordering for data write and busy status check.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
There is off-by-one error in sandbox_emul_gpio that causes
segfault of certain tests.
EMUL_GPIO_REG_END is the address of last valid (emulated) register.
This patch fixed this (by adding one more element to emulated register array).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
ISS is obsolete now and nSIM is used for simulation instead.
In its turn nSIM properly handles baud-rate settings so get rid
of now useless check.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The dwmmc.h include was forgotten during the migration of dwmmc
probing to DM. Since the shiny DM is in place now, remove this
relic of the past.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
musb_lowlevelinit(): if no device is plugged in / detected call
musb_stop() to undo the preceding musb_start() call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The probe function of the musb host driver can be called multiple
times. The code assumes that it can save the pointer to the allocated
musb struct in the driver model priv_auto_alloc data, but this data
gets free-ed on a probe failure or on removal, so we must save the
pointer elsewhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Changes the return type of fdt_usb_get_node_type from char* to int
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Move usb device-tree fixup framework from ehci-fsl.c to common place so
that it can be used by other drivers as well (xhci-fsl.c).
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
This commit fixes crash on BananaPi (and possibly others)
casued by 3f9f8a5b83.
Crash reason:
When no ops were passed to ehci_register(), USB host driver caused
NULL pointer dereference.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
This driver adds support of PIC32 MUSB OTG controller as dual role device.
It implements platform specific glue to reuse musb core.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Definition of writes{bwlq}, reads{bwlq} are now added into arch specific
asm/io.h. So removing them from driver to fix re-definition error
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SerDes protocols might not enable all l2switch ports. In this case,
these ports should not be configured to perform Rx/Tx operations.
This also fixes an issue when flooded frames were also switched to
disabled ports and frames start to accumulate, consuming memory
and eventually causing head-of-line blocking for other frames.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Support Driver Model for fsl esdhc driver.
1. Introduce a new structure struct fsl_esdhc_priv
2. Refactor fsl_esdhc_initialize which is originally used by board code.
- Introduce fsl_esdhc_init to be common usage for DM and non-DM
- Introduce fsl_esdhc_cfg_to_priv to build the bridge for non-DM part.
- The original API for board code is still there, but we use
'fsl_esdhc_cfg_to_priv' and 'fsl_esdhc_init' to serve it.
3. All the functions are changed to use 'struct fsl_esdhc_priv', except
fsl_esdhc_initialize.
4. Since clk driver is not implemented, use mxc_get_clock to geth
the clk and fill 'priv->sdhc_clk'.
Has been tested on i.MX6UL 14X14 EVK board:
"
=>dm tree
....
simple_bus [ + ] | `-- aips-bus@02100000
mmc [ + ] | |-- usdhc@02190000
mmc [ + ] | |-- usdhc@02194000
....
=> mmc list
FSL_SDHC: 0 (SD)
FSL_SDHC: 1 (SD)
"
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Hector Palacios <hector.palacios@digi.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-By: Eric Nelson <eric@nelint.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Claim the MPP pins for the NAND flash controller only when it's actually
being used. This allows the pins to be shared with the SPI interface
which already supports an equivalent on-access MPP reconfiguration.
Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently only chip-select 0 is supported by the kirkwood SPI driver.
The Armada XP / 38x SoCs also use this driver and support multiple chip
selects. This patch adds support for multiple CS on MVEBU.
The register definitions are restructured a bit with this patch. Grouping
them to the corresponding registers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jteki@openedev.com>
PCS auto negotaiation bit should be enabled
along with SGMII autonegotation enabled
in phy.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support of SGMII to TI phy dp838367
Enable the SGMII and PCS settings in phy
control, CFG2 and BIST registers
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Return error from probe in case of invalid phy address.
This fixes the issue of uboot crash if phy is not detected.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.
Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In SGMII cases the isolate bit might set after DMA and
ethernet resets and hence check and clear during
setup_phy if it was set.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pass appropriate interface type to phy_connect
instead of zero.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support of SGMII interface for zynq GEM.
Read xlnx,emio property from DT.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the mvpp2 ethernet controller which is integrated
in the Marvell Armada 375 SoC. This port is based on the Linux driver (v4.4),
which has been stripped of the in U-Boot unused portions.
Tested on the Marvell Armada 375 eval board db-88f6720.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
This enables this driver for the Marvell Armada 375 SoC.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviwer-by: Jagan Teki <jteki@openedev.com>
The RTL8211B_driver structure in drivers/net/phy/realtek.c contains a
wrong PHY ID (0x1cc910 instead of 0x1cc912) in the uid field.
The lowest four bits of the PHY ID encode the chip revision (B+C/D/E/F)
of the RTL8211 and the code originally applied a mask of 0xfffff0 to
the PHY ID, so that matching the PHY ID to the appropriate driver code
was only done on the chip type (RTL8211), but not on a specific
revision.
After introduction of support for the RTL8211E, which needed another
startup function than the older chip revisions, commit
4220504767 changed the mask to 0xffffff
to make the chip revision relevant for the match, but didn't provide
the now-relevant lower bits of the uid field for the RTL8211B/C.
Fix this by setting the full PHY ID in the RTL8211B_driver uid field.
Fixes: 4220504767 ("net/phy: realtek: Fix the PHY ID mask to ensure the correct Realtek PHY is detected")
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a block device cache to speed up repeated reads of block devices by
various filesystems.
This small amount of cache can dramatically speed up filesystem
operations by skipping repeated reads of common areas of a block
device (typically directory structures).
This has shown to have some benefit on FAT filesystem operations of
loading a kernel and RAM disk, but more dramatic benefits on ext4
filesystems when the kernel and/or RAM disk are spread across
multiple extent header structures as described in commit fc0fc50.
The cache is implemented through a minimal list (block_cache) maintained
in most-recently-used order and count of the current number of entries
(cache_count). It uses a maximum block count setting to prevent copies
of large block reads and an upper bound on the number of cached areas.
The maximum number of entries in the cache defaults to 32 and the maximum
number of blocks per cache entry has a default of 2, which has shown to
produce the best results on testing of ext4 and FAT filesystems.
The 'blkcache' command (enabled through CONFIG_CMD_BLOCK_CACHE) allows
changing these values and can be used to tune for a particular filesystem
layout.
Signed-off-by: Eric Nelson <eric@nelint.com>
This driver supports GPIOs present on PM8916 PMIC.
There are 2 device drivers inside:
- GPIO driver (4 "generic" GPIOs)
- Keypad driver that presents itself as GPIO with 2 inputs (power and reset)
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This PMIC is connected on SPMI bus so needs SPMI support enabled.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Support SPMI arbiter on Qualcomm Snapdragon devices.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds emulated spmi bus controller with part of
pm8916 pmic on it to sandbox and tests validating SPMI uclass.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Qualcom processors use proprietary bus to talk with PMIC devices -
SPMI (System Power Management Interface).
On wiring level it is similar to I2C, but on protocol level, it's
multi-master and has simple autodetection capabilities.
This commit adds simple uclass that provides bus read/write interface.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Use definitions from ehci.h instead.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.
This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Debug printf used '%u' to print size_t variable.
This caused warnings on 64-bit machines.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Siva Durga Prasad Paladugu
Stefan Roese
Vikas Manocha
Mateusz Kulikowski
Alexey Brodkin
Marek Vasut
Hans de Goede
Steve Rae
Sriram Dash
Purna Chandra Mandal
York Sun
Codrin Ciubotariu
Peng Fan
Chris Packham
Michal Simek
Joe Hershberger
Karsten Merker
Eric Nelson