Remove unused tx_send_loop variable.
Removes duplicated get_link_status() call from the
keystone2_eth_send_packet().
The emac_gigabit_enable() is called at opening Ethernet and there is no
need to enable it on sending each packet. So remove that call
from keystone2_eth_send_packet() as well.
The calling of power/clock up functions are mostly the responsibility
of SoC/board code, so move these functions to appropriate place.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch removes K2HK SOC specifc emac_regs structure, it uses
soc specific register offset to keep the network driver common across
all the Keystone II EVMs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add support of usb xhci. xHCI controls all USB speeds of the Host
mode, that is, the SS through the SS PHY, as well as the HS, FS, and
LS through the USB2 PHY. xHCI replaces and supersedes all previous
host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not
backwards compatible with any of them. The USB3SS’s USB Controller is
fully compliant with xHC.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav driver is general driver intended to be used for
working with queue manager and pktdma for different IPs like NETCP,
AIF, FFTC, etc. So the it's API shouldn't be named like it works only
with one of them, it should be general names. The names with prefix
like netcp_* rather do for drivers/net/keystone_net.c driver. So it's
good to generalize this driver to be used for different IP's and
delete confusion with real NETCP driver.
The current netcp_* functions of keystone navigator can be used for
other settings of pktdma, not only for NETCP. The API of this driver
is used by the keystone_net driver to work with NETCP, so net driver
also should be corrected. For convenience collect pkdma
configurations in drivers/dma/keystone_nav_cfg.c.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav is used by drivers/net/keystone_net.c driver to
send and receive packets, but currently it's placed at keystone
arch sources. So it should be in the drivers directory also.
It's separate driver that can be used for sending and receiving
pktdma packets by others drivers also.
This patch just move this driver to appropriate directory and
doesn't add any functional changes.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add driver model support in this driver, using platform data provided by
the board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Adjust the driver so that leaf functions take a pointer to the serial port
register base. Put all the global configuration in the init function, and
use the same settings from then on.
This makes it much easier to move to driver model without duplicating the
code, since with driver model we use platform data rather than global
settings.
The driver is compiled with either the CONFIG_PL010_SERIAL or
CONFIG_PL011_SERIAL option and this determines the uart type. With driver
model this needs to come in from platform data, so create a new
CONFIG_PL01X_SERIAL config which brings in the driver, and adjust the
driver to support both peripheral variants.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Add driver model support with this driver. Boards which use this driver
should define platform data in their board files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add driver model support with this driver. In this case the platform data
is in the driver. It would be better to put this into an SOC-specific file,
but this is best attempted when more boards are moved over to use driver
model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Avoid duplicating the code which deals with getc() and putc(). It is fairly
simple, but may expand later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust this driver to use driver model and move smdk5420 boards over to
use it.
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the sandbox cros_ec emulation driver to work with driver model, and
switch over to driver model for sandbox cros_ec.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add support for driver model if enabled. This involves minimal changes
to the code, mostly just plumbing around the edges.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This converts the Tegra SPI drivers to use driver model. This is tested
on:
- Tegra20 - trimslice
- Tegra30 - beaver
- Tegra124 - dalmore
(not tested on Tegra124)
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert sandbox's spi flash emulation driver to use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
We want the SPI flash probing feature to operate as a standard driver.
Add a driver for the basic probing feature used by most boards. This
will be activated by device_probe() as with any other driver.
The 'sf probe' command currently keeps track of the SPI slave that it
last used. This doesn't work with driver model, since some other driver
or system may have probed the device and have access to it too. On the
other hand, if we try to probe a device twice the second probe is a nop
with driver model.
Fix this by searching for the matching device, removing it, and then
probing it again. This should work as expected regardless of other device
activity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a driver model uclass for SPI flash which supports the common
operations (read, write, erase). Since we must keep support for the
non-dm interface, some modification of the spi_flash header is required.
CONFIG_DM_SPI_FLASH is used to enable driver model for SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust spi_flash_probe_slave() to return an error value instead of a
pointer so we get the correct error return.
Have the caller allocate memory for spi_flash to simplify error handling,
and also so that driver model can use its existing allocated memory.
Add a spi.h include in the sf_params file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Since spi_flash.h is supposed to be the public API for SPI flash, move
private things to sf_internal.h. Also tidy up a few comment nits.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Move the exynos SPI driver over to driver model. This removes quite a bit
of boilerplate from the driver, although it adds some for driver model.
A few device tree additions are needed to make the SPI flash available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a new implementation of soft_spi that uses device tree to specify the
GPIOs. This will replace soft_spi_legacy for boards which use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This feature provides for init of a single SPI port for the soft SPI
feature. It is not really compatible with driver model since it assumes a
single SPI port. Also, inserting SPI init into the driver by means of
a #define is not very nice.
This feature is not used by any active boards, so let's remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reserve the 'normal' name for use by driver model, and rename the old
driver so that it is clear that it is for 'legacy' drivers only.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust the sandbox SPI driver to support driver model and move sandbox over
to driver model for SPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Some files are using SPI functions but not explitly including the SPI
header file. Fix this, since driver model needs it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
U-Boot includes a SPI emulation driver already but it is not explicit, and
is hidden in the SPI flash code.
Conceptually with sandbox's SPI implementation we have a layer which
creates SPI bus transitions and a layer which interprets them, currently
only for SPI flash. The latter is actually an emulation, and it should be
possible to add more than one emulation - not just SPI flash.
Add a SPI emulation uclass so that other emulations can be plugged in to
support different types of emulated devices on difference buses/chip
selects.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a uclass which provides access to SPI buses and includes operations
required by SPI.
For a time driver model will need to co-exist with the legacy SPI interface
so some parts of the header file are changed depending on which is in use.
The exports are adjusted also since some functions are not available with
driver model.
Boards must define CONFIG_DM_SPI to use driver model for SPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
(Discussed some follow-up comments which will address in future add-ons)
Buses sometimes want to pass data to their children when they are probed.
For example, a SPI bus may want to tell the slave device about the chip
select it is connected to.
Add a new function to permit the parent data to be supplied to the child.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Buses need to iterate through their children in some situations. Add a few
functions to make this easy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Convert the exynos GPIO driver to driver model. This implements the generic
GPIO interface but not the extra Exynos-specific functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model GPIOs must be requested before use. Make sure this is
done correctly.
(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)
Signed-off-by: Simon Glass <sjg@chromium.org>
The defines at the top of the GPIO driver use single-character names for
parameters which are not very descriptive.
Improve these to use descriptive parameter names.
Signed-off-by: Simon Glass <sjg@chromium.org>
The wrong header is being included, thus requiring the code to re-declare
the generic GPIO interface in each GPIO header.
Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
if (strncmp(name, entry->name, len))
continue;
/* Full match */
if (len == strlen(entry->name))
return entry;
is equivalent to:
if (!strcmp(name, entry->name))
return entry;
The latter is simpler.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The function uclass_add() checks uc_drv->ops as follows:
if (uc_drv->ops) {
dm_warn("No ops for uclass id %d\n", id);
return -EINVAL;
}
It seems odd because it warns "No ops" when uc_drv->ops has
non-NULL pointer. (Looks opposite.)
Anyway, most of UCLASS_DRIVER entries have no .ops member.
This check makes no sense.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Freescale's SEC block has built-in Blob Protocol which provides
a method for protecting user-defined data across system power
cycles. SEC block protects data in a data structure called a Blob,
which provides both confidentiality and integrity protection.
Encapsulating data as a blob
Each time that the Blob Protocol is used to protect data, a
different randomly generated key is used to encrypt the data.
This random key is itself encrypted using a key which is derived
from SoC's non volatile secret key and a 16 bit Key identifier.
The resulting encrypted key along with encrypted data is called a blob.
The non volatile secure key is available for use only during secure boot.
During decapsulation, the reverse process is performed to get back
the original data.
Commands added
--------------
blob enc - encapsulating data as a cryptgraphic blob
blob dec - decapsulating cryptgraphic blob to get the data
Commands Syntax
---------------
blob enc src dst len km
Encapsulate and create blob of data $len bytes long
at address $src and store the result at address $dst.
$km is the 16 byte key modifier is also required for
generation/use as key for cryptographic operation. Key
modifier should be 16 byte long.
blob dec src dst len km
Decapsulate the blob of data at address $src and
store result of $len byte at addr $dst.
$km is the 16 byte key modifier is also required for
generation/use as key for cryptographic operation. Key
modifier should be 16 byte long.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SHA-256 and SHA-1 accelerated using SEC hardware in Freescale SoC's
The driver for SEC (CAAM) IP is based on linux drivers/crypto/caam.
The platforms needto add the MACRO CONFIG_FSL_CAAM inorder to
enable initialization of this hardware IP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The ipu display insists on having a lower_margin smaller
then 2. If this is not the case it will attempt to force
it and adjust the pixclk accordingly. This multiplies pixclk
in Hz with the width and height, since this is typically
a * 10^7 * b * 10^2 * c * 10^2 this will overflow the
uint_32 and make things even worse. Since this is a
bootloader and the adjustment is neglectible, just force
it to two and warn about it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Currently uboot wrongly uses 25mV / step for dcdc3, this is a copy and paste
error introduced when adding the axp152_mvolt_to_target during review of the
axp152.c driver. This results in u-boot setting Vddr to 2.3V instead of 1.5V.
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The DMA/FIS buffers are set in ahci_port_start() which is called
after ahci_host_init(). So don't start the DMA engine here
(i.e. don't set FIS_RX)
This fixes the following error at kernel boot on OMAP platforms (e.g. DRA7x)
WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x260/0x358()
44000000.ocp:L3 Custom Error: MASTER SATA TARGET GPMC (Idle): Data Access in User mode during Functional access
Signed-off-by: Roger Quadros <rogerq@ti.com>
The function nand_flash_detect_ext_param_page() requires
NAND_CMD_RNDOUT command supported. It is necessary to detect some
types of ONFi-compliant devices. Without it, the error message
"unsupported command received 0x5" is shown.
Let's support this command on the Denali NAND controller driver.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
NAND_CMD_PARAM (0xEC) command is not working on the Denali
NAND controller driver.
Unlike NAND_CMD_READID (0x90), when the NAND_CMD_PARAM command
is followed by an address cycle, the target device goes busy.
(R/B# is deasserted)
Wait until the parameter data are ready.
In addition, unnecessary clear_interrupts() should be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
Change this board to add a device tree.
This also adds a pinmux header file although it is not used as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Khoronzhuk, Ivan
Hao Zhang
WingMan Kwok
Simon Glass
Masahiro Yamada
Ruchika Gupta
Jeroen Hofstee
Hans de Goede
Andreas Bießmann
Roger Quadros