The Banana Pi M2-Magic is a small board with an Allwinner A33, an eMMC, a
wifi chip and some pin headers. Enable support for it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Encountered an issue where fastboot can't write to NAND on a CHIP_pro,
the symbol was neither present in the board's config header, nor the
Kconfig, this patch puts it in the Kconfig and defaults on when
SUNXI_NAND is selected.
Signed-off-by: Ben Young <computermouth@crunchbangplusplus.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As explained in arch/arm/mach-sunxi/clock_sun8i_a83t.c, clk for CPU
clusters is computed as clk = 24*n. However, the current formula is clk
= 24*(n-1).
This results in a clock set to a frequency that isn't specified as
possible for CPUs.
Let's use the correct formula.
Fixes: f542948b1e ("sunxi: clk: add basic clocks for A83T")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner SPI flash SPL boot support is guarded by the SPL_SPI_SUNXI
symbol. But despite its generic name, the actual only use case for this
is to provide SPI flash support to the SPL, which requires
CONFIG_SPL_SPI_FLASH_SUPPORT to be defined.
Select this symbol from the SPL_SPI_SUNXI Kconfig definition. This
avoids doing this explicitly in the defconfig, and fixes SPI booting on
the Pine64 SoPine (and -LTS version) and the OrangePi Win board (both with
SPI flash).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Provide a Kconfig option that we can use as dependency for
features that are broken. This allows to easily disable them
without removing the code.
As no short text is supplied the option will not appear in
menuconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
As you see in crypto_algos in common/image-sig.c, the algorithm
should be either "rsa2048" or "rsa4096". "rs2048" is a typo.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Both "conf_name" and "sig_name" point to the name of config node.
The latter should be the name of the signature node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
don't use prettyprint_part_size() in create_gpt_partitions_list()
that avoid to align offset and size to 1 MiB and increase precision for
start and size.
This patch avoid the risk to change partition size and lost data during
rename or swap.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Add test of first and last LBA in gpt for rename and swap.
Only the name is expected to change, so test 3 columns
for part command
1: first LBA (start)
2: last LBA (end)
3: partition name
After rename, the last LBA change and it is a error in current U-Boot code
+ "first" = 0x7ff : invalid value (<start)
+ "second" = 0x17ff => size increasing !
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
+ test write for one partition on all the device (size=0)
+ test write with disk uuid and 2 partitions
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
the partition starting at 0x4400 is refused with overlap error:
$> gpt write mmc 0 "name=test,start=0x4400,size=0"
Writing GPT: Partition overlap
error!
even if the 0x4400 is the first available offset for LBA35 with default
value:
- MBR=LBA1
- GPT header=LBA2
- PTE= 32 LBAs (128 entry), 3 to 34
And the command to have one partition for all the disk failed also :
$> gpt write mmc 0 "name=test,size=0"
After the patch :
$> gpt write mmc 0 "name=test,size=0"
Writing GPT: success!
$> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x01ce9fde "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: b4b84b8a-04e3-4000-0036-aff5c9c495b1
And 0x22 = 34 LBA => offset = 0x4400 is accepted as expected
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
add sandbox test for some gpt sub-command
- gpt read / part list : read the gpt partition created by sgdisk on host
test start, size, LBA and name output
- gpt verify : verify the gpt partition create by sgdisk on host
PS: persistent data test_gpt_disk_image.bin are udpated
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
copy the persistent gpt binary file as it can be modified during the test
that avoid issue if the test fail: the test always restart with clean file
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
RTC_CONFIG_D register contains the day within the month to generate
an alarm, not the month. This corrects the printf to indicate it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Remove hardcoded ftd file name from environment variables.
Use CONFIG_DEFAULT_FDT_FILE macro instead.
Signed-off-by: Michal Oleszczyk <m.oleszczyk@grinn-global.com>
All users of this macro have been converted. Remove MTDDEBUG and
related CONFIG options.
ubifs_dbg_msg_key() is kept. It is silent unless DEBUG is defined.
I am not touching scripts/config_whitelist.txt. The deprecated options
will be dropped by the next resync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In old days, the MTD subsystem in Linux had debug facility like
DEBUG(MTD_DEBUG_LEVEL1, ...).
They were all replaced with pr_debug() until Linux 3.2. See Linux
commit 289c05222172 ("mtd: replace DEBUG() with pr_debug()").
U-Boot still uses similar macros. Covert all of them for easier sync.
Done with the help of Coccinelle.
The semantic patch I used is as follows:
// <smpl>
@@
expression e1, e2;
@@
-MTDDEBUG(e1, e2)
+pr_debug(e2)
@@
expression e1, e2;
@@
-MTDDEBUG(e1, e2,
+pr_debug(e2,
...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit dd74b945af ("ARM: uniphier: use pr_() instead of printf()
where appropriate"), but I missed to update this file for some reason.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If the environment "verify" is set to n, the image verification
is entirely skipped. Remove it as a preparation for verified boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error
when uncompressing Image.gz out of FIT image.
Uncompressing Kernel Image ... Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
UniPhier 32-bit SoCs use CONFIG_SPL_OF_CONTROL. So, many nodes must
be marked as dm-pre-reloc to prevent fdtgrep from stripping them off.
Sprinkling U-Boot-specific properties all over the place is painful
because DT files are synced with Linux from time to time.
Split u-boot,dm-pre-reloc out to uniphier-v7-u-boot.dtsi, which is
appended to UniPhier V7 DTS before the build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The option is never enabled by anyone. Remove the code surrounded
by its ifdef. This should be handled by the clock/reset drivers.
CONFIG_UNIPHIER_ETH in scripts/config_whitelist.txt will be dropped
by the next resync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I thought commit d37d31849c ("ARM: uniphier: enable DWC3 xHCI
driver") enabled CONFIG_USB_DWC3_UNIPHIER, but CONFIG_USB_XHCI_DWC3
was missing in uniphier_v7_defconfig. Re-add.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
CONFIG_SMC911X
CONFIG_SMC911X_BASE
CONFIG_SMC911X_16_BIT
CONFIG_SMC911X_32_BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_MXC
CONFIG_NAND_OMAP_GPMC
CONFIG_NAND_OMAP_GPMC_PREFETCH
CONFIG_NAND_OMAP_ELM
CONFIG_SPL_NAND_AM33XX_BCH
CONFIG_SPL_NAND_SIMPLE
CONFIG_SYS_NAND_BUSWIDTH_16BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
I've missed to add the ACPI resume support to this x86 build target.
This patch adds the ACPI resume support enabling S3 suspend /
resume.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Up to now we depended on an exported variable to build u-boot.rom.
We should be able to specify it in the configuration file, too.
With this patch this becomes possible using the new Kconfig option
CONFIG_BUILD_ROM.
This option depends on CONFIG_X86 and is selected in
qemu-x86_defconfig and qemu-x86_64_defconfig.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Azalia configuration may be different across boards, hence it's not
appropriate to do that in the SoC level. Instead, let's make the
SoC update_fsp_azalia_configs() routine as a weak version, and do
the actual work in the board codes.
So far it seems only som-db5800-som-6867 board enables the Azalia.
Move the original codes into som-db5800-som-6867.c.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present we directly pass the Azalia config pointer to the FSP UPD.
This updates to use a function to do the stuff, like Braswell does.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
So far there are two copies of Azalia struct defines with one in
baytrail and the other one in braswell. This consolidates these
two into one, put it in the common place, and remove the prefix
pch_ to these structs to make their names more generic.
This also corrects reset_wait_timer from us to ms.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is only needed when graphics console is used. For kernel with
native graphics driver, this can be turned off to speed up.
Change this option's default to n in the Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
It was observed that when booting a Ubuntu 16.04 kernel, doing ACPI
S3 suspend/resume sometimes causes the Ubuntu kernel hang forever.
The issue is however not reproduced with a kernel built from i386/
x86_64 defconfig configuration.
The unstability is actually caused by unexpected interrupts being
generated during the S3 resume. For some unknown reason, FSP (gold4)
for BayTrail configures the GPIO DFX5 PAD to enable level interrupt
(bit 24 and 25). As this pin keeps generating interrupts during an
S3 resume, and there is no IRQ requester in the kernel to handle it,
the kernel seems to hang and does not continue resuming.
Clear the mysterious interrupt bits for this pin.
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image
can be built again.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
As "v" is a local variable in stm32_i2c_choose_solution()
"v" has to be copied into "s" to avoid data abort in
stm32_i2c_compute_timing().
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
On qemu errors like
assert 2.999650001525879 >= 3
occur.
According to the comment in the code the test is meant to be
approximate. So we should accept some milliseconds less.
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Update the script to version 0.26 (as of Linux v4.14-rc1)
Keep our "penguin_chief".
Keep our top_of_kernel_tree.
The negative forms of the command line parameters are described
when using --help.
New options are
--git-blame-signatures => when used with --git-blame,
also include all commit signers
--r => include reviewer(s) if any
--letters => print all matching 'letter' types
from all matching sections
File .get_maintainer.ignore can be used to specify
email addressees that shall be ignored.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
'commit fa24eca1f2 ("omap: Add routine for setting fastboot variables")'
adds initial support and usage of "fastboot getvar" command
for DRA75x and DRA72x devices.
and
'commit 0f9e6aee9d ("arm: dra76: Add support for ES1.0 detection")'
adds initial dra76 device definition
This patch is to extend usage of "fastboot getvar" for DRA76 device.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Maxime Ripard
Benjamin Young
Quentin Schulz
Andre Przywara
Heinrich Schuchardt
Masahiro Yamada
Patrick Delaunay
Bin Meng
Michal Oleszczyk
Tom Rini
Adam Ford
Stefan Roese
Patrice Chotard
Christophe Kerello
Praneeth Bajjuri