With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]
For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.
The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by
setting the FIXD bit in the SDR0_MFR register. Here a description of the
symptoms:
Problem Description
------------------------------
If a DMA is performed between memory and PCI with the DMA 1 Controller
using prefetch, and as a result uses a special purpose buffer selected by
the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29),
the first part of the transfer sequence is performed twice. The
PPC440SPe PCI Controller requests more data than was needed such that in
the case of enforce memory protection, a host CPU exception can occur.
No data is corrupted, because data transfer is stopped in the PCI
Controller. Prefetch enable is specified by setting DMA Configuration
Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0.
Behavior that may be observed in a running system
---------------------------------------------------------------------------
1. DMA performance is decreased because of the double access on the PCI bus
interface.
2. If an illegal access to some address on the PCI bus is detected at the
system level, a machine check or similar system error may occur.
Workarounds Available
----------------------------------
1. Do not program prefetch. Note that a prefetch command cannot be programmed
without selecting a special purpose buffer.
2. To avoid crossing a physical boundary of the PCI slave device, add 512
bytes of address to the PCI address range.
This patch was originally provided by Pravin M. Bathija <pbathija@amcc.com>
from AMCC and slighly changed.
Signed-off-by: Pravin M. Bathija <pbathija@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Change all linker scripts to reference the changed driver name 4xx_uart.o.
Note: In most cased all these explicit referencing of these object files
in the linker scripts is not neccessary. Only for manually embedded
environment into the U-Boot image, which is not done is most cases.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some common 4xx macros and the PPC405_SYS_INFO/
PPC440_SYS_INFO structure into the common ppc4xx.h header.
Lot's of other macros are good candidates to be consolidated this way
in the future.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for dynamic configuration of PCIe ports for the
AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe
boards Yucca & Katmai and the 405EX board Kilauea.
This dynamic configuration is done via the "pcie_mode" environement
variable. This variable can be set to "EP" or "RP" for endpoint or
rootpoint mode. Multiple values can be joined via the ":" delimiter.
Here an example:
pcie_mode=RP:EP:EP
This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2
as endpoint.
Per default Yucca will be configured as:
pcie_mode=RP:EP:EP
Per default Katmai will be configured as:
pcie_mode=RP:RP:REP
Per default Kilauea will be configured as:
pcie_mode=RP:RP
Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is the first patch of a series to make the 440SPe PCIe code
usable on different 4xx PPC platforms. In preperation for the new 405EX
which is also equipped with PCIe interfaces.
(2) This patch renames the functions from 440spe_ to 4xx_ with a
little additional cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is the first patch of a series to make the 440SPe PCIe code
usable on different 4xx PPC platforms. In preperation for the new 405EX
which is also equipped with PCIe interfaces.
(1) This patch renames the files from 440spe_pcie to 4xx_pcie
Signed-off-by: Stefan Roese <sr@denx.de>
- 'pciconfighost' is set by default in order to be able to scan bridges
behind the primary host/PCIe
- 'pciscandelay' env variable is recognized to allow for user-controlled
delay before the PCIe bus enumeration; some peripheral devices require a
significant delay before they can be scanned (e.g. LSI8408E); without the
delay they are not detected
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
- correct configuration space mapping
- correct bus numbering
- better access to config space
Prior to this patch, the 440SPe host/PCIe bridge was able to configure only the
first device on the first bus. We now allow to configure up to 16 buses;
also, scanning for devices behind the PCIe-PCIe bridge is supported, so
peripheral devices farther in hierarchy can be identified.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
The new boardspecific DDR2 controller configuration is used for the Yucca
board. Now the Yucca board with 440SPe Rev. A chips is also supported.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.
Signed-off-by: Stefan Roese <sr@denx.de>
The AMCC Yucca now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
Signed-off-by: Stefan Roese <sr@denx.de>
Modifications are based on the linux kernel approach and
support two use cases:
1) Add O= to the make command line
'make O=/tmp/build all'
2) Set environement variable BUILD_DIR to point to the desired location
'export BUILD_DIR=/tmp/build'
'make'
The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'
Command line 'O=' setting overrides BUILD_DIR environent variable.
When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
Improved the memory DIMM detection for the Yucca 440SPe board for
the case where a memory DIMM is falsely detected as present.
This issue is seen on some AMCC Yucca 440SPe validation boards if
only one 512MB memory DIMM is installed, i.e. DIMM slot 0 is
populated and DIMM slot 1 is empty. In this case, U-Boot does
not correctly detect that there is only one DIMM memory module
installed and will falsely detect two DIMM memory modules are
present and therefore U-Boot will not calculate the correct amount
of total memory and u-boot will not booting up.
Patch by Adam Graham, 24 Aug 2006
The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module
integrated in a little aluminium case.
Patch by Martin Krause, 8 Jun 2006
Some code cleanup
Wolfgang Denk
Stefan Roese
Grzegorz Bernacki
Wolfgang Denk
Marian Balakowicz
Rafal Jaworowski
Wolfgang Denk