follow section 15.2.13.1 (Initializing Following Device Power Up or Reset) of
OMAP-L138 DSP+ARM Processor Technical Reference Manual
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
This reverts commit 5347560f5427bcdd48a563b62180481606ac8044,
which was applied only to get release 2012.07 functional on as
many ARM targets as possible despite mis-aligned accesses.
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.
Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
initialize baudrate, flags, data and serial initialization,
only when CONFIG_SPL_LIBCOMMON_SUPPORT is defined.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
This patch adds support for MMC/SD on DA850/OMAP-L138.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
This patch uses the code in omap-common to support gpio modules 1-3
on am33xx based boards.
It adds base address and register definitions, enables clocks to the
modules, and enables building the common gpio code for CONFIG_AM33XX
as well as CONFIG_OMAP
Signed-off-by: Steve Sakoman <steve@sakoman.com>
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
asm/clk.h was included get_peripheral_clk_rate function. But this
is not used from anywhere.
This removed asm/clk.h, and deleted include line from arch/sh/lib/time.c
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Calculation of the bit position using switch statement can substitute
shift operation using ffs.
And removed unsed macro and variable.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This changed into access using array of structure from access to the register
using the definition of the register by macro.
And removed white space.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fixes the build-time warning:
board.c: At top level:
board.c:106: warning: 'pmu_init' defined but not used
This makes the ifdef logic at the call site match the logic at the
function definition.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fixes the build-time warning:
board.c: In function 'board_init_r':
board.c:304: warning: unused variable 's'
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Nothing is using this, so punt it from the gd. Seems to just be a copy
& paste wart from the initial port.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When reset code is in flash, the jump instructions emitted by the
compiler are relative instead of absolute jumps.
A fix to the reset code to make correct jumps to the beginning of
code relocated to RAM have also been added.
Signed-off-by: Julius Baxter <juliusbaxter@gmail.com>
Prototype declaration of I/O operation functions are not correct. as both
'extern' and function definition are at same place.
Chage protoype declaration as static.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Return type of in_8, in_be16 and in_le16 should not be'int'. Update it to type
u8/u16/u32.
Although 'unsigned' for in_be32 and in_le32 is correct. But to make return type
uniform across the file changed to u32
Similarly, parameter passed to out_8, out_be16, out_le16 ,out_be32 & out_le32
should not be 'int'.Change it to type u8/u16/u32.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
All the global flag defines are the same across all arches. So unify them
in one place, and add a simple way for arches to extend for their needs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SET_PCI_LIODN() macro takes a compatible property string as a parameter, so that it knows
which PCI device tree node to look for. The calls to these macros are using a hard-coded string,
but we already have the CONFIG_SYS_FSL_PCIE_COMPAT macro which contains the same string, so we
should use that.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit 48f6a5c34 removed E bit. BSC9130/1 were left out due to patch apply
timing. Remove them now.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The BR_PHYS_ADDR(x) macro was missing parentheses around "x" in the macro
definition, so callers had to supply their own parenthesis.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
fsl_ddr_get_dimm_params() should be wrapped by
CONFIG_SYS_DDR_RAW_TIMING, otherwise, when using fixed_sdram() instead of
using SPD, it will cause compile error.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The fix for errata workaround is to avoid covering physical address
0xff000000 to 0xffffffff during the implementation. Early commit eb672e92
works until DDR size exceeds 4GB. This fix works for DDR size up to 64GB.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Even if using CPU is SH-4A, the previous code always put "SH4".
This patch fixes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
struct s3c24x0_i2c is being moved to common local header file so that
the same can be used by s3c series and exynos series SoCs.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch defined EXYNOS5_I2C_SPACING used to calculate I2C channel
base address.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds the base address for I2C.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds i2c clock information for EXYNOS5.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
cpu.c: In function ‘check_CPU’:
cpu.c:256:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Subject slightly changed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested on TQM855MDCBAB7-T66.102 (MPC855T at 66 MHz) and
TQM860LDB0A3-T50.202 (MPC860T at 50MHz).
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
An empty flush_dcache_range() was added into MPC83xx and MPC85xx to
work with drivers shared with other architecture. However, it is
compiled only if USB is set, but it is required for other drivers
(FSL_ESDHC), too.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Andy Fleming <afleming@gmail.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Marek Vasut <marex@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Added MPC83xx version.
Signed-off-by: Wolfgang Denk <wd@denx.de>
bad_cache_range actually returned true if the range was OK, but it was used
according to its name, which resulted in all valid dcache range invalidate/flush
operations being dropped. Hence, most DMA transfers resulted in garbage data.
This patch renames this function according to what it does, and it fixes the
interpretation of its return value by other functions. The chosen naming is the
same as for ARM926EJ-S in order to be consistent.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Stefano Babic <sbabic@denx.de>
Use the same name as defined in the datasheet.
DSP_CLK -> DISP_CLK
Signed-off-by: Ashok Kumar Reddy Kourla <ashokkourla2000@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
This commit does the following updates.
1. Split the common cache access from cpu.c into lib folder.
2. Rename the following cache api to adapt common.h
- dcache_flush_rang -> flush_dcache_rang
- icache_inval_range -> invalidate_icache_range
3. Add invalidate_dcache_range
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Create a weak-aliased arch_cpu_init, so that we can get rid of CONFIG_ARCH_CPU_INIT
and always call arch_cpu_init.
This way we do not need to define CONFIG_ARCH_CPU_INIT in every board file, since
arch_cpu_init() is supposed to handle common CPU level code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Recent compiler generates unaligned memory access in armv7 default.
But current U-Boot does not allow unaligned memory access, so it causes
data abort exception.
This patch add compile option "-mno-unaligned-access" if it is available.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Tested-by: Gary Thomas <gary@mlbassoc.com>
In currently, when __bss_start is equal to __bss_end__,
The bss loop will clear all the things in memory space.
But just only when __bss_end__ greater than __bss_start__,
we do the clear bss section operation.
Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
As suggested by Graeme Russ, move gd and bd data structrures
to BSS instead of calculating the locations around the stack
and heap.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Clear and prepare for device-tree driven configuration.
Remove CONFIG_SYS_INTC_0 definition
Use dynamic allocation instead of static.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Simon Glass <sjg@chromium.org>
Move __udelay to the timer code because of unification.
And clean coding style because of checkpatch.pl.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Simon Glass <sjg@chromium.org>