The driver provides regulator set/get voltage
enable/disable functions for palmas family of PMICs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write funtions to access pmic
registers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The ctrl reg contains bit fields to enable and disable regulators,
and volt_reg has the bit fields to configure the voltage values.
The registers are frequently accessed hence make them part
of dm_regulator_uclass_platdata structure.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for gpio regulators. As of now this driver caters
to gpio regulators with one gpio. Supports setting voltage values to gpio
regulators and retrieving the values.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These two options go together and it is best to do the conversion in one
step. So enable DM_MMC_OPS by default if DM_MMC is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now we can use compiler wrapper such as ccache or distcc for buildman.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Simon Glass <sjg@chromium.org>
Fixed commit subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
If we use the '/' operator then python 3.x will produce a float, and
refuse to multiply the string sequence in Conv_name_to_c by it with:
TypeError: can't multiply sequence by non-int of type 'float'
Use the '//' operator instead to enforce that we want integer rather
than floating point division.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Simon Glass <sjg@chromium.org>
On python 3.x struct.unpack will complain if we provide it with a
string since it expects to operate on a bytes object. In order to
satisfy this requirement, encode the string to a bytes object when
running on python 3.x.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Simon Glass <sjg@chromium.org>
In python 3.x the iteritems() method has been removed from dictionaries,
and the items() method does effectively the same thing. On python 2.x
using items() is a little less efficient since it involves copying data,
but as speed isn't a concern in the affected code switch to using
items() anyway for simplicity.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Simon Glass <sjg@chromium.org>
In python 3.x StringIO is no longer a module, and the class can instead
be found in the io module. Adjust the code in the doctest input to
account for both.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Simon Glass <sjg@chromium.org>
In python 3.x the iteritems() method has been removed from dictionaries,
and the items() method does effectively the same thing. On python 2.x
using items() is a little less efficient since it involves copying data,
but as speed isn't a concern in this code switch to using items() anyway
for simplicity.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Simon Glass <sjg@chromium.org>
In python 3.x module names used in import statements are case sensitive,
and the configparser module is named in all lower-case. Import it as such
in order to avoid errors when running with python 3.x.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Simon Glass <sjg@chromium.org>
Syntax for exception handling is a little more strict in python 3.x.
Convert all uses to a form accepted by both python 2.x & python 3.x.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Simon Glass <sjg@chromium.org>
In python 3.x, print must be used as a function call. Convert all print
statements to the function call style, importing from __future__ where
we print with no trailing newline or print to a file object.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Simon Glass <sjg@chromium.org>
In preparation for running on python 3.x, which will refuse to run
scripts which mix tabs & spaces for indentation, replace 2 tab
characters present in series.py with spaces.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Simon Glass <sjg@chromium.org>
We need to test both the normal (Python libfdt module) and fallback (fdtget)
implementations of the Fdt class. Add a way to select which implementation
to use.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no need to pass a node path separately. Instead we should use the
path for the node provided. Correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit fixes an issue where data is written to an
invalid memory location.
The issue has been introduced in commit
(88364387 cros: add cros_ec_driver)
Cc: Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add command to print out the flash info as reported by the
ec. The data read back includes size, write block size,
erase block size.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
Add support for reading back flash parameters as reported by
the ec.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
When Ctrl-C is pressed, just exited quietly. There is no sense in displaying
a stack trace since buildman will always be in the same place: waiting for
threads to complete building all the jobs on the queue.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is annoying that buildman does not respond cleanly to Ctrl-C or SIGINT,
particularly on machines with lots of CPUS. Unfortunately queue.join()
blocks the main thread and does not allow it to see the signal. Use a
separate thread instead,
Signed-off-by: Simon Glass <sjg@chromium.org>
If patman is installed on the machine (e.g. in the standard dist-packages
directory), it will find libraries from there in preference to our local
libraries. Adjust the order of the path to ensure that local libraries are
found first.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make it clear when buildman actually starts building. This happens when it
has prepared the threads, working directory and output directories.
Signed-off-by: Simon Glass <sjg@chromium.org>
When buildman starts, it prepares its output directory by removing any old
build directories which will not be used this time. This can happen if a
previous build left directories around for commit hashes which are no-longer
part of the branch.
This can take quite a while, so print a message to indicate what is going
on.
Signed-off-by: Simon Glass <sjg@chromium.org>
On a machine with a lot of CPUs this prints a lot of useless lines of the
form:
Cloning repo for thread <n>
Adjust the output so that these all appear on one line, and disappear when
the cloning is complete.
Note: This cloning is actually unnecessary and very wasteful on disk space
(about 3.5GB each time). It would be better to create symlinks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Output which does not include a newline will not be displayed unless
flushed. Add a flush to ensure that it becomes visible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add silicon ID code for AM437x silicon. This can be used to print
the cpu info using CONFIG_DISPLAY_CPUINFO.
Also printing "CPU :" along with cpu name in order to be consistent
with other OMAP platforms.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
By default saveenv option is not supported for SPL. This patch
enable the support for save environment variable for SPL build.
Enable save environment support in SPL after setenv. By default
the saveenv option is not provided in SPL, but some boards need
this support in 'Falcon' boot, where SPL need to boot from
different images based on environment variable set by OS. For
example OS may set "reboot_image" environment variable to
"recovery" inorder to boot recovery image by SPL. The SPL read
"reboot_image" and act accordingly and change the reboot_image
to default mode using setenv and save the environemnt.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Simon Glass <sig@chromium.org>
change in v1:
- dropped SUPPORT, use CONFIG_SPL_SAVEENV
- updates the comments in mmc_private.h
Boards where ECs that use a I2C port != 0 specify this in the
devicetree file via the google,remote-bus property.
Previously this was ignored and hardcoded to port 0.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
As a standard practice complex definitions should be protected
with parentheses, as it might fail when used in a complex if
statements.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The normal longjmp command allows for a caller to pass the return value
of the setjmp() invocation. This patch adds that semantic to the arm
implementation of it and adjusts the efi_loader call respectively.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The default lockname is set to /var/lock. This limits the
usage of this application where OS uses different lockfile
location parameter.
For example, In case of android, the default lock
path location is /data.
Hence by providing the command line option to input lockfile
path will be useful to reuse the tool across multiple
operating system.
usage: ./fw_printenv -l <lockfile path>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
The SPL size for dra7x platform increased beyond 64K,
increasing the size to 256K to cater for future enhancement.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
removing CONFIG_SPL_ENV_SUPPORT defined in header files
due to moved to kconfig option for CONFIG_SPL_ENV_SUPPORT
Signed-off-by: Ravi Babu <ravibabu@ti.com>
This reverts commit 82f5279b0c.
The build failure of k2*evm boards was fixed in a different way by
the previous commit. It is nasty to patch generic drivers around
with #ifdef CONFIG_CLK just for the KeyStone's matter.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The KeyStone platform has its own clk_get_rate() but its prototype
is different from that of the common-clk (clk-uclass) framework.
Prefix the KeyStone specific implementation with ks_ in order to
avoid name-space conflict.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Due to clock source restrictions on i.MX6, certain pixel clock rates can
not be supported. Hence default the resolution/frame rate during boot to a
supported value by passing video bootargs 1024x768@60 for
HDMI (Display Port1) and LVDS (Display Port2) on B850v3.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
These two functions are neither defined nor referenced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Our build system still parses ad-hoc CONFIG options in header files
and generates include/autoconf.mk so that Makefiles can reference
them. This gimmick was introduced in the pre-Kconfig days and will
be kept until Kconfig migration is completed.
The include/autoconf.mk is generated like follows:
[1] Preprocess include/common.h with -DDO_DEPS_ONLY and
retrieve macros into include/autoconf.mk.tmp
[2] Reformat include/autoconf.mk.dep into include/autoconf.mk
with tools/scripts/define2mk.sed script
[3] Remove include/autoconf.mk.tmp
Here, include/autoconf.mk.tmp is similar to u-boot.cfg, which is
also generated by preprocessing include/config.h with -DDO_DEPS_ONLY.
In other words, there is much overlap among include/autoconf.mk and
u-boot.cfg build rules.
So, the idea is to split the build rule of include/autoconf.mk
into two stages. The first preprocesses headers into u-boot.cfg.
The second parses the u-boot.cfg into include/autoconf.mk. The
build rules of u-boot.cfg in Makefile and spl/Makefile will be gone.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
I do not remember why I wrote the code like this, but let's make it
a bit more readable.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Keerthy
Simon Glass
York Sun
Paul Burton
Moritz Fischer
Tom Rini
Lokesh Vutla
B, Ravi
Mugunthan V N
Alexander Graf
Masahiro Yamada
Ken Lin