Currently when we define CONFIG_SERIAL_TAG we will barf with a failure to
define "struct tag_serialnr".
This structure is defined in <asm/setup.h>, this patch includes
<asm/setup.h> to fix.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
When the DDR calibration is enabled, a situation may happen that it
will fail on a few select boards out of a whole production lot. In
particular, after the first write leveling stage, the MPWLDECTRLx
registers will contain a value 0x1nn , for nn usually being 0x7f or
slightly lower.
What this means is that the HW write leveling detected that the DQS
rising edge on one or more bundles arrives slightly _after_ CLK and
therefore when the DDR DRAM samples CLK on the DQS rising edge, the
CLK signal is already high (cfr. AN4467 rev2 Figure 7 on page 18).
The HW write leveling then ends up adding almost an entire cycle (thus
the 0x17f) to the DQS delay, which indeed aligns it, but also triggers
subsequent calibration failure in DQS gating due to this massive offset.
There are two observations here:
- If the MPWLDECTRLx value is corrected from 0x17f to 0x0 , then the
DQS gating passes, the entire calibration passes as well and the
DRAM is perfectly stable even under massive load.
- When using the NXP DRAM calibrator for iMX6/7, the value 0x17f or so
in MPWLDECTRx register is not there, but it is replaced by 0x0 as one
would expect.
Someone from NXP finally explains why, quoting [1]:
"
Having said all that, the DDR Stress Test does something that we
do not advertise to the users. The Stress Test iself looks at the
values of the MPWLDECTRL0/1 fields before reporting results, and
if it sees any filed with a value greater than 200/256 delay
(reported as half-cycle = 0x1 and ABS_OFFSET > 0x48), the DDR
Stress test will reset the Write Leveling delay for this lane
to 0x000 and not report it in the log.
The reason that the DDR Stress test does this is because a delay
of more than 78% a clock cycle means that the DQS edge is arriving
within the JEDEC tolerence of 25% of the clock edge. In most cases,
DQS is arriving < 5% tCK of the SDCLK edge in the early case, and
it does not make sense to delay the DQS strobe almost a full clock
cycle and add extra latency to each Write burst just to make the
two edges align exactly. In this case, we are guilty of making a
decision for the customer without telling them we are doing it so
that we don't have to provide the above explanation to every customer.
They don't need to know it.
"
This patch adds the correction described above, that is if the MPWLDECTRx
value is over 0x148, the value is corrected back to 0x0.
[1] https://community.nxp.com/thread/456246
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The u-boot-ivt.img.log file contains 0x prefixes in the HAB Blocks line,
while the SPL.log does not. For consistency, and to make it easier to
extract and put into a .csf file for use with NXP's code signing tool,
add 0x prefixes here.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
The current makefile logic disables creation of the
SPL.log/u-boot-ivt.img.log etc. files when V=1 is given on the command
line, the rationale presumably being that the user wants and gets the
information on the console.
However, from general principles, I don't think a higher V= level
should affect which build artifacts get generated (and certainly
shouldn't produce fewer). Concretely, it's also a problem that when
doing a V=1 build in a terminal, the relevant HAB blocks lines easily
drown in all the other V=1 output.
Moreover, build systems such as Yocto by default pass V=1, so in that
case the information gets hidden away in the do_compile log file, making
it nigh impossible to create a recipe for creating signed U-boot images
- I don't want to disable V=1, because having verbose output in the log
file is valuable when things go wrong, but OTOH trying to go digging in
the do_compile log file (and getting exactly the right lines) is not
pleasant to even think about.
So change the logic so that for V=0, the mkimage output is redirected
to MKIMAGEOUTPUT (which is also the current behaviour), while for any
other value of V, we _additionally_ write the information to make's
stdout, whatever that might be.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Breno Lima <breno.lima@nxp.com>
Synchronize the naming with Linux, call the common code TMIO.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop the CONFIG_MMC_RENESAS_TUNING symbol from Gen3 configs.
This symbol is no longer used after the Matsushita SDHI driver,
instead the renesas-sdhi driver uses CONFIG_MMC_HS200_SUPPORT
to discern whether the tuning support should be compiled in.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
--
V2: Submit this on top of configs which are actually in mainline
There is currently no use for building the SPL anymore, since the
SPI loader can easily be replaced by TPL and TPL does load U-Boot
directly. Upgrade TPL to SPL and replace what used to be SPL with
it. This way we build the U-Boot sources only twice, not thrice.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Shrink the TPL by using tiny printf and tiny memset by default.
This removes the biggest symbol -- vsnprintf_internal -- from
the TPL and reduces the text segment by about 2 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Stout port was broken since some time. This patch updates
the H2 Stout port to use modern frameworks, DM, DT probing, SPL
and TPL for the preloading and puts it on par with the M2 Porter
board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Stout uses SCIFA0 for serial console, make sure it is
available very early on when probing from DT.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add the SCIFA0 address entry so it can be used in TPL if needed
due to size restrictions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add compatible strings for R8A7790, R8A7793 and R8A7794, since the
contemporary DTs use those don't have a generic match value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The initconst is not used in U-Boot, drop it. The r8a7790_crit_mod_clks
is also not used in U-Boot, so drop it too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- For am335x_pdu001 we do not want the CPSW driver, drop it
- Re-sync the defconfig for am43xx_evm_rtconly as it came in after the
patch that converted CPSW to Kconfig was posted but before it was
applied.
- Drop empty section / comments from pengwyn
- Drop empty section / comments from baltos and drop unused
CONFIG_SPL_NET_VCI_STRING (it does not enable CONFIG_SPL_NET_SUPPORT
currently and SPL_NET_VCI_STRING has been migrated already).
Cc: Felix Brack <fb@ltec.ch>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Fixes: f02b8d1761 ("Migrate CONFIG_DRIVER_TI_CPSW to Kconfig")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
Tested-by: Felix Brack <fb@ltec.ch>
Without armv8_setup_psci register VBAR_EL3 is not set up property which
makes SMC calls jump to invalid location.
smp_kick_all_cpus is required to make slave cpus leave gic_wait_for_interrupt.
Without this they will never pursue booting process.
Fix was applied to the two ways of booting VxWorks: bootvx and bootm commands.
This implementation is very similar to what is done in boot_jump_linux
in arch/arm/lib/bootm.c file.
Tested on VxWorks 7 release SR0520 2017-12-08 Intel Stratix 10 SX SoC
Development Kit board.
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@globallogic.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Otherwise, we see this:
In file included from include/configs/zynq-common.h:183:0,
from include/config.h:5,
from include/common.h:21,
from env/common.c:11:
include/config_distro_bootcmd.h:319:2: error: expected ?}? before ?BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE?
BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE
^
include/config_distro_bootcmd.h:319:2: note: in definition of macro ?BOOTENV_DEV_NAME_PXE?
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This reverts the parts of commit 3b3ea2c56e
where it changed the EFI dependency on NET.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
The BOOTP options used to be and should still be default for all boards
with CMD_NET enabled. One should not be forced to use DISTRO_DEFAULTS to
get them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Improve the documentation and correct the listed dependencies.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Commit 3b3ea2c56e ("Kconfig: cmd: Make networking command dependent on NET")
removed the help documentation from the README but didn't add it back to Kconfig.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
The options were pretty unhelpful, so improve them some.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Move DHCP to directly follow BOOTP so that Kconfig can show the
dependency as a hierarchy.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Options that controlled the tftp and bootp commands depended on their
commands, but lived in the net menu.
Move them so they are in a consistent location.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
PING requires CMD_NET, not NET.
Also, CMD_NET already depends on NET, so no need to directly depend
on it.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Previously, CMD_NET was an alias for 2 commands (bootp and tftpboot) and
they we not able to be disabled. Separate out those 2 commands and move
CMD_NET up to the menu level, which more accurately represents the code.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Add compatible strings for R8A7790, R8A7793 and R8A7794, since the
contemporary DTs use those don't have a generic match value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support to use max-speed property from dt for
determining the supported speed. Use 1000Mbps as
default.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since the probe function has changed to reset FEC controller prior than
setup PHY. If reset FEC controller timeout, the priv->phydev is not
initialized, so can't free it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On i.MX6SX, 6UL and 7D, there are two enet controllers each has a
MDIO port. But Some boards share one MDIO port for the two enets. So
introduce a configuration CONFIG_FEC_MXC_MDIO_BASE to indicate
the MDIO port for sharing.
In Kconfig, user needs enable CONFIG_FEC_MXC_SHARE_MDIO first to enter
the CONFIG_FEC_MXC_MDIO_BASE.
To i.MX28, adapt to use the new config
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
To platforms has two enet interface, using dev->seq could
avoid conflict.
i.MX6UL/ULL evk board net get the wrong MAC address from fuse,
eth1 get MAC0 address, eth0 get MAC1 address from fuse. Set the
priv->dev_id to device->seq as the real net interface alias id then
.fec_get_hwaddr() read the related MAC address from fuse.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
No need to provide two prototype for this function.
Use ulong for the first parameter, then this function
could be shared for DM/non DM case.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When using ethernet DM driver, the recv interface has a
change with non-DM interface, that driver needs to set
the packet pointer and provide it to upper layer to process.
In fec driver, the fecmxc_recv functions does not handle the
packet pointer parameter. This may cause crash in upper layer
processing because the packet pointer is not set.
This patch allocates a buffer for the packet pointer and free it
through free_pkt interface.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
mvneta already supports setting the MAC address but this was only done
internally when some other part of U-Boot tries to actually use the
interface. This commit exposes this functionality to the ethernet core
code so that the MAC addresses of all interfaces are configured
correctly even if they are not used before loading Linux.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Make it possible to use gcc code coverage analysis.
v1 -> v2:
- Kconfig: remove not needed 'default n'
- Makefile: use consistent spacing
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The dwc_ahci has been broken for quite some time now. The breakage has been
introduced by the series "dm: scsi: Enhance SCSI support for driver model"
Use ahci_bind_scsi() and ahci_probe_scsi() to properly bind and probe the
driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The Gen3 kernel images are often above 8 MiB, increase the
maximum kernel size to 64 MiB to future-proof it, just like
many other ARM64 boards do.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix up the memory map on Gen3 to match datasheet properly.
This simplifies the memory map setup as well, since we do
no longer need this massive complexity.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The QSPI controller on RCar Gen2 has 32byte FIFO. Instead of doing
the SPI transmission 1 byte at time, if there is a 32byte chunk of
data to be transferred, fill the FIFO completely and then transfer
the data to/from the FIFO. This increases the SPI NOR access speed
significantly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Replace the ad-hoc endless loops with wait_for_bit() with
reasonable timeout. Note that the loops had internal 10uS
delays, although there is no reason for those on this HW,
so they are dropped.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Waiting for SPBDCR == 1 is not required and is covered by the
subsequent wait for SPSR_SPRFF, so drop this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Just replace unsigned {char,short,long} with u{8,16,32},
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Add driver for the RPC block in SPI-flash mode. This driver allows
access to a SPI NOR flash attached to the RPC block and does not
support RPC in Hyperflash mode. Note that this block is extremely
selective when communicating with the SPI NOR.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Bryan O'Donoghue
Marek Vasut
Rasmus Villemoes
Marek Vasut
Heinrich Schuchardt
Tom Rini
Vasyl Vavrychuk
Joe Hershberger
Marek Vasut
Siva Durga Prasad Paladugu
Ye Li
Peng Fan
Matt Pelland
Christian Gmeiner
Jean-Jacques Hiblot