This patch adds support for the Lyrtech SFF-SDR board,
based on the TI DaVinci architecture (ARM926EJS).
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Philip Balister <philip@balister.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This moves the MMC and SD Card command definitions from
include/asm/arch/mmc.h into include/mmc.h. These definitions are
given by the MMC and SD Card standards, not by any particular
architecture.
There's a lot more room for consolidation in the MMC drivers which
I'm hoping to get done eventually, but this patch is a start.
Compile-tested for all avr32 boards as well as lpc2292sodimm and
lubbock. This should cover all three mmc drivers in the tree.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
ALIGN() returns the smallest aligned value greater than the passed
in address or size. Taken from Linux.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Building for 4xx doesn't work since commit 4dbdb768:
In file included from 4xx_pcie.c:28:
include/asm/processor.h:971: error: expected ')' before 'ver'
make[1]: *** [4xx_pcie.o] Error 1
This patch fixes the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
This updates the lmb code to use phys_size_t
and phys_addr_t instead of unsigned long. Other code
which interacts with this code, like getenv_bootm_size()
is also updated.
Booted on MPC8641HPCN, build-tested ppc, arm, mips.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Currently, both are defined as an unsigned long, but
should be phys_size_t. This should result in no real change,
since phys_size_t is currently an unsigned long for all the
default configs. Also add print_lnum to cmd_bdinfo to deal
with the potentially wider memsize.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
LAWs have the concept of priority so its useful to be able to allocate
the lowest (highest number) priority. We will end up using this with the
new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so we keep track of which LAWs have allocated and provide
a function (set_next_law) which can allocate a LAW for us if one is
free.
In the future we will move to doing more "dynamic" LAW allocation
since the majority of users dont really care about what LAW number
they are at.
Also, add CONFIG_MPC8540 or CONFIG_MPC8560 to those boards which needed them
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
A number of board ports have empty version of board_early_init_f
for no reason since we control its via CONFIG_BOARD_EARLY_INIT_F.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove unused and unconfigured DDR test code from FSL 85xx boards.
Besides, other common code exists.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some TQM85xx boards could be equipped with up to 1 GiB (NOR) Flash
memory. The current memory map only supports up to 128 MiB Flash.
This patch adds the configuration option CONFIG_TQM_BIGFLASH. If
set, up to 1 GiB flash is supported. To achieve this, the memory
map has to be adjusted in great parts (for example the CCSRBAR is
moved from 0xE0000000 to 0xA0000000).
If you want to boot Linux with CONFIG_TQM_BIGFLASH set, the new
memory map also has to be considered in the kernel (changed
CCSRBAR address, changed PCI IO base address, ...). Please use
an appropriate Flat Device Tree blob (tqm8548.dtb).
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
This patch adds support for NAND FLASH on the TQM8548. It is disabled by
default and can be enabled for the TQM8548 modules. It is now based on
the re-written FSL NAND UPM driver. A patch has been posted earlier today
with the subject:
"NAND FSL UPM: driver re-write using the hwcontrol callback"
Note that the R/B pin is not supported by that module requiring to use
the specified maximum delay time.
Note: With NAND support enabled the size of the U-Boot image exceeds
256 KB and TEXT_BASE must therefore be set to 0xfff80000 in config.mk,
doubling the image size :-(.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
This patch adds support for PCI express cards. The board support
now uses common FSL PCI init code, for both, PCI and PCIe on all
TQM85xx modules.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
This patch adds basic support for the TQM8548 module from TQ-Components
(http://www.tqc.de/) including DDR2 SDRAM initialisation and support for
eTSEC 3 and 4
Furthermore Flash buffer write has been enabled to speed up output to
the Flash by approx. a factor of 10.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
This patch adds support for Linux kernels using the Flat Device Tree.
It also re-defines the default environment settings for booting Linux
with the FDT blob.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
This patch adds initialization of the UPMC RAM to support up to two
Intel 82527 compatible CAN controller on the TQM85xx modules.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
The 'N' type Spansion flashes (S29GLxxxN series) have bigger sectors,
than the formerly used 'M' types (S29GLxxxM series), so the flash layout
needs to be changed -> new start address of the environment. The macro
definition CONFIG_TQM_FLASH_N_TYPE is undefined by default and must be
defined for boards with 'N' type flashes.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
differentiate with local variables of the same name by renaming the
global 'fdt' variable 'working_fdt'.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This is a re-write of the NAND FSL UPM driver using the more universal
hwcontrol callback (instead of the cmdfunc callback). Here is a brief
list of furher modifications:
- For the time being, the UPM setup writing the UPM array has been
removed from the driver and must now be done by the board specific
code.
- The bus width definition in "struct fsl_upm_nand" is now in bits to
comply with the corresponding Linux driver and 8, 16 and 32 bit
accesses are supported.
- chip->dev_read is only set if fun->dev_ready != NULL, which is
required for boards not connecting the R/B pin.
- A few issue have been fixed with MxMR bit manipulation like in the
corresponding Linux driver.
Note: I think the "io_addr" field of "struct fsl_upm" could be removed
as well, because the address is already determined by
"nand->IO_ADDR_[RW]", but I'm not 100% sure.
This patch has been tested on a TQM8548 modules with the NAND chip
Micron MT29F8G08FABWP.
This patch is based on the following patches posted to this list a few
minutes ago:
PPC: add accessor macros to clear and set bits in one shot
83xx/85xx/86xx: add more MxMR local bus definitions
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
PPC: add accessor macros to clear and set bits in one shot
This patch adds macros from linux/include/asm-powerpc/io.h to clear and
set bits in one shot using the in_be32, out_be32, etc. accessor functions.
They are very handy to manipulate bits it I/O registers.
This patch is required for my forthcoming FSL NAND UPM driver re-write and
the support for the TQM8548 module.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
83xx/85xx/86xx: add more MxMR local bus definitions
This patch adds more macro definitions for the UPM Machine Mode Registers
They are copied from "include/mpc82xx.h" to simplify the merge of all 8xxx
common local bus definitions into include/asm-ppc/fsl_lbc.h. They are
required for my forthcoming FSL NAND UPM driver re-write and the support
for the TQM8548 module.
This patch is based on the following two patches from Anton Vorontsov:
http://www.mail-archive.com/u-boot-users@lists.sourceforge.net/msg06511.htmlhttp://www.mail-archive.com/u-boot-users@lists.sourceforge.net/msg06587.html
I leave coding style violation fixes, code beautification and name
corrections to somebody else ;-(.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Merge mpc85xx.h's LBC defines to fsl_lbc.h. Also, adopt ACS names
from mpc85xx.h, so ACS_0b10 renamed to ACS_DIV4, ACS_0b11 to ACS_DIV2.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
This patch moves Freescale Localbus defines out of mpc83xx.h, so we could
use it on MPC85xx and MPC86xx processors.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
The current cpu identification code is used just to return the name
of the processor at boot. There are some other locations that the name
is useful (device tree setup). Expose the functionality to other bits
of code.
Also, drop the 'E' suffix and add it on by looking at the SVR version
when we print this out. This is mainly to allow the most flexible use
of the name. The device tree code tends to not care about the 'E' suffix.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add MPC8343 based board mvBlueLYNX-M7.
It's a single board stereo camera system.
Please read doc/README.mvblm7 for details.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
move the BRx_* and ORx_* left behind in mpc85xx.h
The same is needed for mpc8xx.h and mpc8260.h (defines are almost
the same, just few differences which needs some attention though).
But the bad news for mpc8xx and mpc8260 is that there are a lot of users
of these defines. So this cleanup I'll leave for the "better times".
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch moves Freescale Localbus defines out of mpc83xx.h, so we could
use it on MPC85xx and MPC86xx processors.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Use CONFIG_OF_LIBFDT instead to support flattened device trees. It is
cleaner, has better functionality, and is better supported.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This was configured to use the deprecated CONFIG_OF_FLAT_TREE, change
to CONFIG_OF_LIBFDT.
WARNING: It appears that this board lost its ability to boot via a
flattened device tree prior to this changeset.
WARNING: This conversion was untested because I do not have a board to
test it on.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This was configured to use the deprecated CONFIG_OF_FLAT_TREE, change
to CONFIG_OF_LIBFDT.
WARNING: This conversion is untested because I do not have a board to
test it on.
NOTE: The FDT blob (DTS) must have an /aliases/ethernet0 and (optionally)
/aliases/ethernet1 property for the ethernet to work.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
SH7763RDP has SCIF, NOR Flash, Ethernet, USB host, LCDC and MMC.
In this patch, support SCIF, NOR Flash, and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CONFIG_SOC_AU1X00
Common Alchemy Au1x00 stuff. All Alchemy processor based machines
need to have this config as a system type specifier.
CONFIG_SOC_AU1000, CONFIG_SOC_AU1100, CONFIG_SOC_AU1200,
CONFIG_SOC_AU1500, CONFIG_SOC_AU1550
Machine type specifiers. Each port should have one of aboves.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This patch series unifies the AMCC eval board ports by introducing
a common include header for all AMCC eval boards:
include/configs/amcc-common.h
This header now includes all common configuration options/defines which
are removed from the board specific headers.
The reason for this is ease of maintenance and unified look and feel
of all AMCC boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Steven A. Falco
Kumar Gala
Ben Warren
Jean-Christophe PLAGNIOL-VILLARD
Wolfgang Denk
Hugo Villeneuve
Haavard Skinnemoen
Andy Fleming
Anatolij Gustschin
Becky Bruce
Sergei Poselenov
Wolfgang Grandegger
Kim Phillips
Anton Vorontsov
Andre Schwarz
Tor Krill
Gerald Van Baren
Nobuhiro Iwamatsu
Shinya Kuribayashi
Stefan Roese