Here's another USB storage patch. Currently U-Boot handles storage
devices #0 - #4 as valid devices, even if there is none connected. This
patch fixes usb_stor_get_dev() to check detected device count instead
of MAX-define.
This is very important for ill behaving devices. usb_dev_desc[] can be
partially initialized if device probe fails.
After fixing get_dev() it was easy to fix "usb part" etc commands.
Previously it outputed "Unknown partition table" five times, now it's
"no USB devices available".
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
Add NEC EHCI controller to the list of the supported devices.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
drivers/usb/host/ehci-pci.c | 1 +
1 file changed, 1 insertion(+)
Commit b416191a14 (Fix EHCI port reset.) didn't
move the code that checked for successful clearing of the port reset bit from
ehci_submit_root(), relying on wait_ms() call instead. The mentioned code also
erroneously reported port reset state when the reset was already completed.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
USB devices on the 2nd port are not detected and I get the following message:
The request port(1) is not configured
That's with default CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS value of 2. 'req->index'
is 1-based, so the comparison in ehci_submit_root() can't be correct.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
On little endian machines, EHCI root hub's USB revision is reported as 0.2 --
cpu_to_le16() was missed in the initializer for the 'bcdUSB' descriptor field.
The same should be done for the 'bcdDevice' field.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
This patch adds reset_timer() before the flash status check
waiting loop.
Since the timer is basically running asynchronous to the cfi
code, it is possible to call get_timer(0), then only a few
_SYSCLK_ cycles later an interrupt is generated. This causes
timeout even though much less time has elapsed. So the timer
period registers should be reset before get_timer(0) is
called.
There is similar usage in nand_base.c.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
The MPC8536DS_NAND SPL build was failing due to code size increase
introduced by commit:
commit 33f57bd553
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Fri Mar 26 15:14:43 2010 -0500
85xx: Fix enabling of L1 cache parity on secondary cores
We built in some NS16550 functions that we dont need and can get
rid of them via CONFIG_NS16550_MIN_FUNCTIONS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P2020DS board uses a new type of PIXIS FPGA, called the ngPIXIS.
The ngPIXIS has one distinct new feature: the values of the on-board switches
can be selectively overridden with shadow registers. This feature is used to
boot from a different NOR flash bank, instead of having a register dedicated
for this purpose. Because the ngPIXIS is so different from the previous PIXIS,
a new file is introduced: ngpixis.c.
Also update the P2020DS checkboard() function to use the new macros defined
in the header file.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactor and document the Freescale PIXIS code, used on most 85xx and 86xx
boards. This makes the code easier to read and more flexible.
Delete pixis.h, because none of the exported functions were actually being
used by any other file. Make all of the functions in pixis.c 'static'.
Remove "#include pixis.h" from every file that has it.
Remove some unnecessary #includes.
Make 'pixis_base' into a macro, so that we don't need to define it in every
function.
Add "while(1);" loops at the end of functions that reset the board, so that
execution doesn't continue while the reset is in progress.
Replace in_8/out_8 calls with clrbits_8, setbits_8, or clrsetbits_8, where
appropriate.
Replace ulong/uint with their spelled-out equivalents. Remove unnecessary
typecasts, changing the types of some variables if necessary.
Add CONFIG_SYS_PIXIS_VCFGEN0_ENABLE and CONFIG_SYS_PIXIS_VBOOT_ENABLE to make
it easier for specific boards to support variations in the PIXIS registers
sets. No current boards appears to need this feature.
Fix the definition of CONFIG_SYS_PIXIS_VBOOT_MASK for the MPC8610 HPCD.
Apparently, "pixis_reset altbank" has never worked on this board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The HID1[MBDD] bit is new on rev5.0 or greater cores and will optimize
the performance of mbar/eieio instructions.
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added P1012/P1013/P1021/P1022 to cpu_type_list and SVR list
* Added number of LAWs for P1012/P1013/P1021/P1022
* Set CONFIG_MAX_CPUS to 2 for P1021/P1022
* PCI port config
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If the PCI controller wasn't configured or enabled delete from the
device tree (include its alias).
For the case that we didn't even configure u-boot with knowledge of
the controller we can use the fact that the pci_controller pointer
is NULL to delete the node in the device tree. We determine that
a controller was not setup (because of HW config) based on the fact
that cfg_addr wasn't setup.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a helper function that given an alias will delete both the node
the alias points to and the alias itself
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
For 64B cacheline SoC, set the fixed 8-beat burst len,
for 32B cacheline SoC, set the On-The-Fly as default.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Read-to-read/Write-to-write turnaround for same chip select
of DDR3 memory, BL/2+2 cycles is enough for them at BC4 and
OTF case, BL/2 cycles is enough for fixed BL8.
Cutting down the turnaround from BL/2+4 to BL/2+2 or BL/2
will improve the memory performance.
Signed-off-by: Dave Liu <daveliu@freescale.com>
When we set the read or write watermark in WML we should maintain the
rest of the register as is, rather than using some hard coded value.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To support multiple block read command we must set abort or use auto
CMD12. If we booted from eSDHC controller neither of these are used
and thus we need to reset the controller to allow multiple block read
to function.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need to stop the clocks on 83xx/85xx as well as imx. No need to make
this code conditional to just imx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch moves the PPC4xx specific I2C device driver into the I2C
drivers directory. All 4xx config headers are updated to include this
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
pci_eth_init() is already conditional to CONFIG_PCI so not every caller
needs to have conditionals.
This is the only place in the current code base where such a check is
still at the calling site.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Peter Pearse <peter.pearse@arm.com>
This patch is part of migrating the AT91 support towards
using C struct for all SOC access.
It removes one more CONFIG_AT91_LEGACY warning.
at91_pmc.h needs cleanup after migration of the drivers
has been done.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Previous code was failing when reading back the timer less than
400us after resetting it. This lead nand operations to incorrectly
timeout any now and then. Moreover, writing the load register isn't
immediately reflected in the value register. We must wait for a clock
edge, so read_timer now waits for the value to change at least once,
otherwise nand operation would timeout anyways (though less frequently).
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
CONFIG_CMD_AUTOSCRIPT support is deprecated and non-existing
This clean up patch removes the references for esd boards
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
ep93xx timer: Simplified the timer code by eliminating clk_to_systicks() and
performing (almost) all manipulation of the timer structure in read_timer()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
ep93xx timer: Renamed pointers to struct timer_regs from name 'timer' to
'timer_regs' in order to avoid confusion with the global variable 'timer'
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Add setup for ethernet on SMDKC100, allowing kernel/ramdisk to be
loaded over tftp.
The preinit function will configure GPIO (GPK0CON) & SROMC to look
for environment in SROM Bank 3.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Nand Flash, Ethernet, other features might need to configure the
SROMC registers accordingly.
The config_sromc() functions helps with this.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Memory subsystem of S5PC100 handles SROM, SRAM, OneDRAM, OneNand,
NAND Flash, DDRs.
smc.h is a common place for the register description of Memory subsystem
of S5PC100.
Note: Only SROM related registers are descibed now.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The s3c6400.h file is only for S3C64XX cpu and the pheripheral port
address(0x70000000 - 0x7fffffff) exists at only S3C64XX cpu, so they
should be included by only S3C64XX cpu.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The get_pll_clk(int) API returns the PLL frequency based on
the (int) argument which is defined locally in clock.c
Moving that #define to common header file (clk.h) would
be helpful when using the API from other files.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When the timestamp is incremented via interrupt and the interrupt
period is greater than 1 msec, successive calls to get_timer() can
produce inaccurate timing since the interrupts are asynchronous
to the timing loop. For example, with an interrupt period of 10 msec
two successive calls to get_timer() could indicate an elapsed time
of 10 msec after only several hundred usecs -- depending on when
the next interrupt actually occurs. This behavior can cause
reliability issues with components such as CFI and NAND.
This can be remedied by calling reset_timer() prior to establishing
the base timestamp with get_timer(0), provided reset_timer()
resets the hardware timer (rather than simply resetting only the
timestamp). This has the effect of synchronizing the interrupts
(and the advance of the timestamp) with the timing loop.
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
This patch adds bootargs passing to nios2 linux.
The args passing is enabled with,
r4 : 'NIOS' magic
r5 : pointer to initrd start
r6 : pointer to initrd end
r7 : pointer to command line
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
CONFIG_SYS_HZ was being calculated (incorrectly) in nios2 configuration
headers. Updated comments to accurately describe timebase macros.
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
The outx/writex macros were using writex(addr, val) rather than
the standard writex(val, addr), resulting in incompatibilty with
architecture independent components. This change set uses standard
parameter order.
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Kim B. Heino
Sergei Shtylyov
Wolfgang Denk
Thomas Chou
Kumar Gala
Timur Tabi
Sandeep Gopalpet
Dave Liu
Roy Zang
Jerry Huang
Stefan Roese
Detlev Zundel
Matthias Fuchs
Asen Dimov
Alessandro Rubini
Achim Ehrlich
Daniel Gorsulowski
Matthias Kaehlcke
Naveen Krishna CH
Minkyu Kang
Joonyoung Shim
Naveen Krishna CH
Vipin KUMAR
Scott McNutt