- block_dev_desc_t says that block_(read|write) take lbaint_t for blkcnt
not ulong.
- We also move the extern of sata_dev_desc into <sata.h>
- Remove now duplicate declarations from driver-specific headers.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Cast first parameter to sata_cpy()
In /drivers/block/ata_piix.h, ata_id_has_lba48(), ata_id_has_lba(),
ata_id_has_dma(), ata_id_u32(), ata_id_u64() are all defined in
include/libata.h which is included in ata.h which is included by all files
which include ata_piix.h (only ata_piix.c) so these definitions are
supurflous to (and conlict with) this in libata.h. Interestingly, my
compiler complains about ata_id_u64 already being defined, but not
ata_id_u32
ata_dump_id() is defined in include/libata.h and should not be static
(maybe should even use ata_dump_id() in libata.c
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Cast first parameter to sata_cpy()
In /drivers/block/ata_piix.h, ata_id_has_lba48(), ata_id_has_lba(),
ata_id_has_dma(), ata_id_u32(), ata_id_u64() are all defined in
include/libata.h which is included in ata.h which is included by all files
which include ata_piix.h (only ata_piix.c) so these definitions are
supurflous to (and conlict with) this in libata.h. Interestingly, my
compiler complains about ata_id_u64 already being defined, but not
ata_id_u32
ata_dump_id() is defined in include/libata.h and should not be static
(maybe should even use ata_dump_id() in libata.c
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
original ata_piix driver is using IDE framework, not real
SATA framework. For now, the ata_piix driver is only used
by x86 sc520_cdp board. This patch makes the ata_piix driver
use the new SATA framework, so
- remove the duplicated command stuff
- remove the CONFIG_CMD_IDE define in the sc520_cdp.h
- add the CONFIG_CMD_SATA define to sc520_cdp.h
Signed-off-by: Dave Liu <daveliu@freescale.com>
move the cmd_sata.c from common/ to drivers/ata_piix.c,
the cmd_sata.c have some part of ata_piix controller drivers.
consolidate the driver to have better framework.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Bridge, ICH-5, ICH-6 and ICH-7.
Implementation:
1. Code is divided in to two files. All functions, which are
controller specific are kept in "drivers/ata_piix.c" file and
functions, which are not controller specific, are kept in
"common/cmd_sata.c" file.
2. Reading and Writing from the S-ATA drive is done using PIO method.
3. Driver can be configured for 48-bit addressing by defining macro
CONFIG_LBA48, if this macro is not defined driver uses the 28-bit
addressing.
4. S-ATA read function is hooked to the File system, commands like
ext2ls and ext2load file can be used. This has been tested.
5. U-Boot command "SATA_init" is added, which initializes the S-ATA
controller and identifies the S-ATA drives connected to it.
6. U-Boot command "sata" is added, which is used to read/write, print
partition table and get info about the drives present. This I have
implemented in same way as "ide" command is implemented in U-Boot.
7. This driver is for S-ATA in native mode.
8. This driver does not support the Native command queuing and
Hot-plugging.
Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
Pavel Herrmann
Tom Rini
Graeme Russ
Jean-Christophe PLAGNIOL-VILLARD
Dave Liu
Mushtaq Khan
Wolfgang Denk
mushtaq khan