The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.
Signed-off-by: Tom Rini <trini@ti.com>
CONFIG_NET_MULTI is not used anymore, so remove it from board files.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Revision B of the board uses CSD0 for the DRAM,
as usual for MX3 boards. The patch fixes also
some values in the U-Boot environment.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port>
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Helmut Raiger <helmut.raiger@hale.at>
CC: John Rigby <jcrigby@gmail.com>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
The flea3 board is a custom board by CarMediaLab used
in automotive.
Network (FEC), NOR, NAND and SPI are supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This renames BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT.
Along the way it removes some leftover
#define BOARD_LATE_INIT 1
and adds some basic documentation for board specific
callbacks in README.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).
The board boots from the NOR flash. Following devices
are supported:
- two ethernet devices (FEC and SMC911x on debug board)
- I2C
- PMIC (MC13892) via I2C interface
- UART
- NOR flash (64MB)
- NAND flash (2GB)
- basic access to mc9sdz60 registers via I2C interface
Signed-off-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam
Troy Kisky
Tom Rini
Stefano Babic
Fabio Estevam
Helmut Raiger
Mike Frysinger