Use CONFIG_SYS_PCI*_IO_BUS for the bus relative address instead
of _IO_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_SYS_{PCI,RIO}_MEM_BUS for the bus relative address instead
of _MEM_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
So that we can locate the DDR tlb start entry to the value other than 8. By
default, it is still 8.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Currently MPC85xx and MPC86xx boards just calculate the localbus frequency
and print it out, but don't save it.
This changes where its calculated and stored to be more consistent with the
CPU, CCB, TB, and DDR frequencies and the MPC83xx localbus clock.
The localbus frequency is added to sysinfo and calculated when sysinfo is
set up, in cpu/mpc8[56]xx/speed.c, the same as the other frequencies are.
get_clocks() copies the frequency into the global data, as the other
frequencies are, into a new field that is only enabled for MPC85xx and
MPC86xx.
checkcpu() in cpu/mpc8[56]xx/cpu.c will print out the local bus frequency
from sysinfo, like the other frequencies, instead of calculating it on the
spot.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
The clock divider for the MPC8568 local bus should be doubled, like the
other newer MPC85xx chips.
Since there are now more chips with a 2x divider than a 1x, and any new
85xx chips will probably be 2x, invert the sense of the #if so that it
lists the 1x chips instead of the 2x ones.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
If one custom board is using the 8MB flash, it is set
as FLASH_BASE = 0xef000000, TEXT_BASE = 0xef780000.
The current start.S code will be broken at switch_as.
It is because the TLB1[15] is set as 16MB page size,
EPN = TEXT_BASE & 0xff000000, RPN = 0xff000000.
For the 8MB flash case, the EPN = 0xefxxxxxx,
RPN = 0xffxxxxxx. Assume the virt address of switch_as
is 0xef7ff18c, the real address of the instruction at
switch_as should be 0xff7ff18c. the 0xff7ff18c is out
of the range of the default 8MB boot LAW window
0xff800000 - 0xffffffff.
So when we switch to AS1 address space at switch_as,
the core can't fetch the instruction at switch_as any
more. It will cause broken issue.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Assuming the OSes exception vectors start from the base of kernel address, and
the kernel physical starting address can be relocated to an non-zero address.
This patch enables the second core to have a valid IVPR for debugger before
kernel setting IVPR in CAMP mode. Otherwise, IVPR is 0x0 and it is not a valid
value for second core which runs kernel at different physical address other
than 0x0.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits
instead of four.
In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It
should be safe as the fifth bit was defined as reserved and set to 0.
Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Export the localbus frequency in the device tree, the same way the CPU, TB,
CCB, and various other frequencies are exported in their respective device
tree nodes.
Some localbus devices need this information to be programed correctly, so
it makes sense to export it along with the other frequencies.
Unfortunately, when someone wrote the localbus dts bindings, they didn't
bother to define what the "compatible" property should be. So it seems no
one was quite sure what to put in their dts files.
Based on current existing dts files in the kernel source, I've used
"fsl,pq3-localbus" and "fsl,elbc" for MPC85xx, which are used by almost all
of the 85xx devices, and are looked for by the Linux code. The eLBC is
apparently not entirely backward compatible with the pq3 LBC and so eLBC
equipped platforms like 8572 won't use pq3-localbus.
For MPC86xx, I've used "fsl,elbc" which is used by some of the 86xx systems
and is also looked for by the Linux code. On MPC8641, I've also used
"fsl,mpc8641-localbus" as it is also commonly used in dts files, some of
which don't use "fsl,elbc" or any other acceptable name to match on.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Moved up the initialization of GD so C code like set_tlb() can use
gd->flags to determine if we've relocated or not in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
If the virtual address for CCSRBAR is the same after relocation but
the physical address is changing we'd end up having two TLB entries with
the same VA. Instead we new us the new CCSRBAR virt address + 4k as a
temp virt address to access the old CCSRBAR to relocate it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Add define used to determine if PCI1 interface is in PCI or PCIX mode.
Convert users of the old PORDEVSR_PCI constant to use MPC85xx_PORDEVSR_PCI1
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
All mpc8548-based boards should implement the suggested workaround
to CPU 2 errata. Without the workaround, its possible for the
8548's core to hang while executing a msync or mbar 0 instruction
and a snoopable transaction from an I/O master tagged to make
quick forward progress is present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Affected boards:
Several MPC8xx boards
Several MPC8260/MPC8272 boards
Several MPC85xx boards
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8572 DDR erratum1:
DDR controller may enter an illegal state when operating
in 32-bit bus mode with 4-beat bursts.
Description:
When operating with a 32-bit bus, it is recommended that
DDR_SDRAM_CFG[8_BE] is cleared when DDR2 memories are used.
This forces the DDR controller to use 4-beat bursts when
communicating to the DRAMs. However, an issue exists that
could lead to data corruption when the DDR controller is
in 32-bit bus mode while using 4-beat bursts.
Projected Impact:
If the DDR controller is operating in 32-bit bus mode with
4-beat bursts, then the controller may enter into a bad state.
All subsequent reads from memory is corrupted.
Four-beat bursts with a 32-bit bus only is used with DDR2 memories.
Therefore, this erratum does not affect DDR3 mode.
Work Arounds:
To work around this issue, software must set DEBUG_1[31] in
DDR memory mapped space (CCSRBAR offset + 0x2f00 for DDR_1
and CCSRBAR offset + 0x6f00 for DDR_2).
Currenlty, the code is using incorrect register DDR_SDRAM_CFG_2
as condition, but it should be DDR_SDRAM_CFG register.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Introduce CONFIG_E500MC to deal with the minor differences between
e500v2 and e500mc.
* Certain fields of HID0/1 don't exist anymore on e500mc
* Cache line size is 64-bytes on e500mc
* reset value of PIR is different
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Using CONFIG_SYS_CACHELINE_SIZE instead of 31 means we can handle
e500mc's 64-byte cacheline properly when it gets added.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some cores don't support ethernet stashing at all, and some
instances have errata. Adds 3 properties to gianfar nodes
which support stashing. For now, just add this support to
85xx SoCs.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Added the ability for C code to invalidate the i/d-cache's and
to flush the d-cache. This allows us to more efficient change mappings
from cache-able to cache-inhibited.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit dffd2446fb.
The fix introduced by this patch is not correct. The problem is
that the documentation is not correct for the MPC8544 with regards
to which bit in PORDEVSR2 is for the SEC_CFG.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Measurements with our MPC8544 board showed that the I2C bus frequency
is wrong by a factor of 1.5. Obviously, the interpretation of the
MPC85xx_PORDEVSR2_SEC_CFG bit of the cfg_sec_freq register is not
correct. There seems to be an error in the 8544 RM.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
On 8536DS board, When the DDR clk is set async mode(SW3[6:8] != 111),
The display is still sync mode DDR freq. This patch try to fix
this. The display DDR freq is now the actual freq in both
sync and async mode.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
ePAPR says if the *cache-block-size is the same as *cache-line-size
than we don't need the *cache-line-size property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix printf format-string/arg mismatches under -DDEBUG.
These warnings occur with DEBUG defined for a platform using
cpu/mpc85xx. Users of other architectures can unearth similar
problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right
after "CFLAGS += $(call cc-option,-fno-stack-protector)".
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The e500um says the timebase is volatile out of reset. To ensure
TB sync works we need to make sure its zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The tsec driver contains a hard-coded array of configuration information
for the tsec ethernet controllers. We create a default function that works
for most tsecs, and allow that to be overridden by board code. It creates
an array of tsec_info structures, which are then parsed by the corresponding
driver instance to determine configuration. Also, add regs, miiregs, and
devname fields to the tsec_info structure, so that we don't need the kludgy
"index" parameter.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
For some reason we duplicated the majority of code in lib_ppc/interrupts.c
not show how that happened, but there is no good reason for it.
Use the interrupt_init_cpu() and timer_interrupt_cpu() since its why
they exist.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536 Adds SDHC and SATA controllers to the PQ3 family. We
also have SERDES init code for the 8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
The main purpose of this rewrite it to be able to share the same
initialization code on all FSL PowerPC products that have DDR
controllers. (83xx, 85xx, 86xx).
The code is broken up into the following steps:
GET_SPD
COMPUTE_DIMM_PARMS
COMPUTE_COMMON_PARMS
GATHER_OPTS
ASSIGN_ADDRESSES
COMPUTE_REGS
PROGRAM_REGS
This allows us to share more code an easily allow for board specific code
overrides.
Additionally this code base adds support for >4G of DDR and provides a
foundation for supporting interleaving on processors with more than one
controller.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move to using the environment variables 'ethaddr', 'eth1addr', etc..
instead of bd->bi_enetaddr, bi_enet1addr, etc.
This makes the code a bit more flexible to the number of ethernet
interfaces.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_NUM_CPUS to match existing define used by 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
The L2 size detection code was a bit confusing and we kept having to add
code to it to handle new processors. Change the sense of detection so we
look for the older processors that aren't changing.
Also added support for 1M cache size on 8572.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some boards that have external 16550 UARTs don't have a direct
tie between bi_busfreq and the clock used for the UARTs. Boards
that do have such a tie should set CFG_NS16550_CLK to be
get_bus_freq(0) -- which most of them do already.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
With a page size of BOOKE_PAGESZ_16M, both the real and effective
addresses must be multiples of 16MB. The hardware silently truncates
them so the code happens to work. This patch clarifies the situation
by establishing addresses that the hardware doesn't need to truncate.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Delete the crypto node if not on an E-processor. If on 8360 or 834x family,
check rev and up-rev crypto node (to SEC rev. 2.4 property values)
if on an 'EA' processor, e.g. MPC8349EA.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kumar Gala
Haiying Wang
Trent Piepho
Dave Liu
Peter Tyser
Ben Warren
Wolfgang Denk
Ed Swarthout
Andy Fleming
Jean-Christophe PLAGNIOL-VILLARD
Wolfgang Grandegger
Jason Jin
Andrew Klossner
Sergei Poselenov
Paul Gortmaker
Kim Phillips