As per updated board design, different QSPI flash
is connected on boards, hence change QSPI flash type
from Micron n25q512a device to spansion s25fs512s
device in dts and config.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is not necessary for every SoC to have 2 SATA controller.
So put SATA1, SATA2 code under respective defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch provides default implementations of the two functions
set_uart_mux_conf and set_mux_conf_regs. Hence boards not using
them do not need to provide their distinct empty definitions.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.
For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adapts stm32h743 disco and eval dts files to match
with U-boot requirements or add features wich are not yet
upstreamed on kernel side :
_ Add RCC clock driver node and update all clocks phandle
accordingly.
By default, on kernel side, all clocks was temporarly
configured as a phandle to timer_clk waiting for a RCC
clock driver to be available.
On U-boot side, we now have a dedicated RCC clock driver, we
can configured all clocks as phandle to this driver.
All this binding update will be available soon in a kernel tag,
as all the bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
_ Align STM32H7 serial compatible string with the one which will be
available in next kernel tag. The bindings has been acked by
Rob Herring [2].
This compatible string will be usefull to add stm32h7 specific
feature for this serial driver.
[2] https://lkml.org/lkml/2017/7/17/739
_ Add gpio compatible and aliases for stm32h743
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add missing HSI and CSI oscillators nodes needed
by STM32H7 RCC clock driver.
Clock sources could be:
_ HSE (High Speed External)
_ HSI (High Speed Internal)
_ CSI (Low Power Internal)
These clocks can be used as clocksource in some configuration.
By default, HSE is selected as clock source.
_ Set HSE to 25Mhz for stm32h743i-disco and eval board
By default, the external oscillator frequency is defined at
25 Mhz in SoC stm32h743.dtsi file.
It has been set at 125 Mhz in kernel DT temporarly waiting for
RCC clock driver becomes available.
As in U-boot we got a RCC clock driver, the real value of HSE
clock can be used.
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This file is imported from linux kernel v4.13
Add device tree support for STM32H743 evaluation board.
This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS and FS
_ I2 C compatible serial interface
_ RTC with rechargeable backup battery
_ SAI Audio DAC
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM, 1Mx16bit SRAM and 8Mx16bit NOR Flash
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Potentiometer
_ 4 colored user LEDs
_ Reset, wakeup, tamper or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
Power jack
3 USB with Micro-AB
RS-232 communications
Ethernet RJ45
FD-CAN compliant connection
Stereo headset jack including analog microphone input
2 audio jacks for external speakers
microSD™ card
JTAG/SWD and ETM trace
_ Expansion connectors:
Extension connectors and memory connectors for daughterboard
or wire-wrap board
_ Flexible power-supply options: ST-LINK USB VBUS or external
sources
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All these files are imported from linux kernel v4.13
Add device tree support for STM32H743 SoC and discovery
board. This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS
_ I2 C compatible serial interface
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Reset, wakeup, or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
1 USB with Micro-AB
Ethernet RJ45
Stereo headset jack including analog microphone input
microSD™ card
RCA connector
JTAG/SWD and ETM trace
_ Expansion connectors:
Arduino Uno compatible Connectors
2 x PIO connectors (PMOD and PMOD+)
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update ehci and ohci node's compatible string in order to
use ehci-generic and ohci-generic drivers.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On STi 96boards, configure by default the micro USB connector
(managed by DWC3 hardware block) in peripheral mode.
This will allow to use fastboot feature.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.
Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
reset-names property is needed to use the reset
API for STi sdhci driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of having every board file to add its own g_dnl_bind_fixup()
implementation, move it to the common imx6 SPL code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3368 TPL stage always returns to the BootROM, so it has no need
for the eMMC, SD and SPI nodes. This marks those nodes (that should
be included in SPL, but not TPL) as 'u-boot,dm-spl'.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the RK3399-Q7, we need to turn on the on-module USB hub before using the
USB host interfaces (only the OTG interface is directly connected to the edge
connector). This drops the deprecated 'rockchip,vbus-gpio' property and uses
a fixed regulator to turn on the USB hub.
References: 26a8b80 "usb: host: xhci-rockchip: use fixed regulator to control vbus"
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for Vyasa RK3288 initial board
from Amarula Solutions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
On the RK3399, we will have either OF_PLATDATA or full OF_CONTROL
enabled: this allows the use of syscon to retrieve the addresses of
GRF and SGRF (except for the early debug UART setup, which runs so
early that the device-model is not initialised).
This removes the hard-coded addresses and goes through syscon to
retrieve the base-addresses of GRF and SGRF. After that, we use
the structure definitions to locate the respective registers.
In addition to this, the inclusion of header files is also cleaned up:
- all headers are included at the beginning (there was a spurious
inclusion of the grf header from within a function)
- all #include statements for unused headers are removed
- the remaining #include statements are sorted (while keeping common.h
included in front)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support bootstage recording, we want to mark our DM timer as the
tick-timer; this triggers the support for 'trying harder' to read the
timer in the Rockchip DM timer driver, even if the device model isn't
ready yet.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Unfortunately, the integrated macphy default is enabled, which will
increase power consuming, if we do not use this PHY. So let's disable
it at first, which will save power consuming. If we really use it, then
enable it in driver level.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To support fastboot "fastboot reboot-bootloader" cmd.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds USB OTG/EHCI/OHCI nodes for evb-rv1108 USB ports.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update these macros to use all upper-case to avoid checkpatch
warnings:
ENET_25MHz,
ENET_50MHz,
ENET_125MHz,
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The current mechanism using SCR/GPR registers work well when
the serial downloader boot mode has been selected explicitly
(either via boot mode pins or using bmode command). However,
in case the system entered boot ROM due to unbootable primary
boot devices (e.g. empty eMMC), the SPL fails to detect that
it has been downloaded through serial loader and tries to
continue booting from eMMC:
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The only known way to reliably detect USB serial downloader
is by checking the USB PHY receiver block power state...
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
This macro allows to detect whether the USB PHY is active. This
is helpful to detect if the boot ROM has previously started the
USB serial downloader.
The idea is taken from the mfgtool support in the NXP U-Boot:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/?h=imx_v2016.03_4.1.15_2.0.0_ga&id=a352ed3c5184b95c4c9f7468f5fbb5f43de5e412
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Starting from PXs3, the bit fields of RSTCTRL, CLKCTRL registers
will change every SoC. There is no more point to define bitfields
in the common header file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The main difference between Pro4 and PXs2/LD6b is the Denali NAND
IP version. This is now distinguished by DT. Merge the two defconfig
files into uniphier_v7_defconfig.
Update the README.uniphier too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Nothing CONFIG_SOC_DA830 anymore, so let's remove it and
the one remaining source file for it. It appears to have been
abandoned a while ago.
Signed-off-by: Adam Ford <aford173@gmail.com>
commit b63b995 (arm: dts: Add u-boot specific compatibles) separated out
u-boot specific compatibles from dts files.
The u-boot specifics were moved in *-u-boot.dtsi files for all dra7
platforms except dra7-evm.
Without it the SD card is broken on DRA7-evm because the regulator cannot
be enabled.
Fix it by adding the missing dra7-evm-u-boot.dtsi with the needed
properties.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
When the OP-TEE image is built for secure paging the load address may be
in SRAM, remove checks that prevent this.
Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
All these places seem to inherit the codes from the MMC driver where
a FIXME was put in the comment. However the correct operation after
read should be cache invalidate, not flush.
The underlying drivers should be responsible for the cache operation.
Remove these codes completely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: York Sun <york.sun@nxp.com>
Commit 6ae4c3efbd ("ARM: DRA7: Add pinctrl register definitions")
has added new macros for pinmux configuration in line with the kernel
definitions. Cleanup the old pinctrl macros from the common header
file so that they are not used by any new boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
Use the CONFIG_XXXX_BOOT to indicate the boot media, instead of
the CONFIG_SYS_USE_XXXX option, which is declared by
CONFIG_SYS_EXTRA_OPTIONS option.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
As said in READRE.kconfig, include/configs/*.h will be removed
after all options are switched to Kconfig. As the first step,
remove the follow line from include/configs/*.h.
#include <asm/hardware.h>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
To prepare to remove the SoCs options such as SAMA5D2, SAMA5D3
and SAMA5D4 from the CONFIG_SYS_EXTRA_OPTIONS option which is
deprecated, add the SoC options to Kconfig.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The SAMA5D27-SiP (System in Package) integrates the SAMA5D2
with 1Gbit DDR2-SDRAM in a single package.
The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and
Mac-address EEPROM.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SAMA5D2 SiP(System in Package) has different Chip IDs in the
CHIPID and CHIP_EXID registers.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the boot device for booting from the QSPI flash.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refer to the commit 70f8c8316ad(PMC: add new mck function to lower
rate while switching) from AT91Bootstrap.
While switching to a lower clock source, we must switch the clock
source first instead of last. Otherwise, we could end up with
too high frequency on internal bus and peripherals.
This happens on SAMA5D2 as exitting from the ROM code.
Add a function pmc_mck_init_down() to allow this sequence.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As said in 29.5.7 section of SAMA5D2 datasheet, before switching to
the crystal oscillator, a check must be carried out to ensure that
the oscillator is present and that its freqency is valid.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a function to display the company's logo and board information
via the API from DM_VIDEO. This function can be shared by other
atmel boards, so locate it in board/atmel/common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For sama5d2, add the sfr node with syscon support.
In order to access the SFR_UTMICKTRIM register for the utmi clock
driver, add the phandle property for the utmi node to point to the
sfr node.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
By default, it is assumed that the UTMI clock is generated from
a 12 MHz reference clock (MAINCK). If it's not the case, the FREQ
field of the SFR_UTMICKTRIM has to be updated to generate the UTMI
clock in the proper way.
The UTMI clock has a fixed rate of 480 MHz. In fact, there is no
multiplier we can configure. The multiplier is managed internally,
depending on the reference clock frequency, to achieve the target
of 480 MHz.
The patch is cloned from the patch of mailing-list:
[PATCH v2] clk: at91: utmi: set the mainck rate
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
[trini: Depend on SPL_DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_EMIF4
CONFIG_SDRC
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The DTS files had some spacing issues and they needed fixing. This
pull re-sync's the OMAP3xx related DTS files with Linux 4.13-RC5.
To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.
Signed-off-by: Adam Ford <aford173@gmail.com>
V3: The resync broke card detect on MMC1 on Logic PD's Torpedo,
so we add the cd-invert to the Torpedo's -u-boot.dtsi file.
V2: Add the u-boot.dtsi files for OMAP3, OMAP36xx, and Torpedo
Remove the need for the second patch in the series
Masahiro Yamada
Sriram Dash
Santan Kumar
Ashish Kumar
Felix Brack
Patrice Chotard
Fabio Estevam
Kever Yang
Philipp Tomsich
Jagan Teki
David Wu
William Wu
Eric Nelson
Stefan Agner
Adam Ford
Jean-Jacques Hiblot
Harinarayan Bhatta
Bin Meng
Suman Anna
Wenyou Yang
Wenyou Yang