Adding pinmux and IODELAY data for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The dra76-evm is a board based on TI's DRA76 processor
Add eeprom support
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 1 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN
Adding CPU detection support for the dra76 ES1.0 soc
and update prcm, control module, dplls data.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
LP87565 is present on dra76-evm. Select it for
TARGET_DRA7XX_EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz.
When running a SPL target, which supports multiple MX6 variants we cannot
properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as
such decision is done in build-time currently.
Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be
configured in run-time on mx6.
Reported-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
[agust: fixed #endif in cgtqmx6eval.h]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
At present the IDE device number is initialized to -1, which means
we cannot type "ide read" command before setting the device number
via "ide device #".
For convenience, let's set the first device as the default one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When there is no CDROM inserted, the block size is zero hence there
is no need to create a BLK device for it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the IDE driver to driver model so that block read and
write are fully functional.
Fixes: b7c6baef ("x86: Convert MMC to driver model")
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
So far these are using magic numbers. Replace them with macros.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The underlying implementation for ENV_AES has security complications and
is not recommended for use. Please see CVE-2017-3225 and CVE-2017-3226
for more details. Mark this as deprecated now and delete this in the
medium term if no one comes forward to re-work the support.
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of the config options for USB networking have been migrated to
Kconfig. Update README.usb to reflect this.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The correct name is 'gd->fdt_blob', not 'gd->blob'.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need SPL_SYSRESET
for do_reset() in SPL for Rockchip SoCs.
References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_) macro"
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
syscon id table need a dummy member as NULL ending, or else system
will panic while try to match a compatible in this table as a list.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Disable CONFIG_ARCH_FIXUP_FDT_MEMORY to prevent U-Boot from modifying
the memory {} nodes in the DT passed to the Linux kernel. The R8A779x
DT contains multiple memory {} nodes, while U-Boot only modifies the
first one and stuffs all the memory entries into it, which is wrong.
Disabling CONFIG_ARCH_FIXUP_FDT_MEMORY is the least intrusive way to
fix the issue this close to the release, while the real fix is to
extend the fdt_fixup_memory_banks() to handle multiple memory nodes
in DT.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On RCar M3 and on RCar H3 newer than and not including ES1.0, the SD clock
must be divided by 4 rather than 2 because a hardware workaround present
only in the H3 ES1.0 has been removed from these chips. U-Boot currently
only supports M3 and H3 ES 2.0 and newer, so configure the SD pre-divider
to 4 to prevent SD instability.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
In the general case, CONFIG_NFS_READ_SIZE is unchanged from the default
of 1024. There are in fact no in-tree users that increase this size.
Adjust the comment to reflect what could be done in the future in
conjunction with CONFIG_IP_DEFRAG.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The old logic always enabled the TX-delay when the phy-mode was set to
PHY_INTERFACE_MODE_RGMII. With this patch we enable the TX delay for
PHY_INTERFACE_MODE_RGMII_ID and PHY_INTERFACE_MODE_RGMII_TXID and
disable it for PHY_INTERFACE_MODE_RGMII.
Based on a similar change made in the Linux Realtek PHY driver
by Martin Blumenstingl <martin.blumenstingl@googlemail.com>.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: York Sun <york.sun@nxp.com>
The inline documentation of vsprintf mentions a parameter size
which does not exist in the function declaration.
int vsprintf(char *buf, const char *fmt, va_list args);
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This reverts commit 25877d4e4c.
This is a workaround for Raspberry Pi boot failures seen when passing on
the device tree provided by the Raspberry Pi firmware at boot. Without
CONFIG_OF_EMBED, we just get stuck at "Starting kernel ..." when we try
to boot Linux with this device tree.
Signed-off-by: Paul Barker <pbarker@toganlabs.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some files are generated during libfdt build. Ignore them.
This was wrongly put in the .gitignore in the root directory before.
Now let's remove entries there and put them in the right place.
Fixes: 34e2c285 ("gitignore: add intermediates from libfdt build")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This was broken by the recent environment refactoring. Specifically:
$ make environ
scripts/Makefile.build:59: tools/environ/Makefile: No such file or directory
make[1]: *** No rule to make target 'tools/environ/Makefile'. Stop.
make: *** [Makefile:1469: environ] Error 2
Fix this by updating the Makefile and adjusting the #include filesnames in
two C files.
Fixes: ec74f5f (Makefile: Rename 'env' target to 'environ')
Reported-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Since commit 842778a091 ("usb: gadget: g_dnl: only set iSerialNumber
if we have a serial#") "fastboot devices" stopped to show correct device
serial number for TI boards, showing this line instead:
???????????? fastboot
This is because serial# env variable could be set after g_dnl gadget was
initialized (e.g. by using env_set() in the board file).
To fix this, let's update internal serial number variable (g_dnl_serial)
when "serial#" env var is changed.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
With the move of environment code from common/ to env/ a number of
changes needed to be made to various make targets. We missed updating
some of the files required for out of tree builds of the tools. Correct
the 'environ' target to know that we need to work under tools/env/ still
(not tools/environ/) and then update the wrappers in env_attr.c and
env_flags.c to point to the new correct file.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla
Keerthy
Praneeth Bajjuri
Tom Rini
Jorge Ramirez-Ortiz
Fabio Estevam
Bin Meng
Chris Packham
Nobuhiro Iwamatsu
Kever Yang
Marek Vasut
Heinrich Schuchardt
Madalin Bucur
Paul Barker
Alison Chaiken
Simon Glass
Sam Protsenko
Anatolij Gustschin