mx25pdk has a Ethernet port that is connected to its internal FEC controller.
In order to power up the Ethernet PHY (DP83640) it is necessary to communicate
with the MC34704 PMIC via I2C.
Make the FEC ethernet port functional
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
imx-regs.h is meant to contain SoC register definitions.
Common SoC funtions should go to sys_proto.h instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Introduce FSL_PMIC_I2C_LENGTH to configure the number of bytes that are used to
communicate with the PMIC via I2C.
Instead of hardcoding the value, pass the number via a configurable option per
PMIC type.
This will be useful for adding support for PMIC MC34704 from Freescale, which
uses only one byte in its I2C protocol.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx25pdk has a SD/MMC slot connected to esdhc1.
Add support for it and allow the environment variables to be saved into SD/MMC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
It is necessary to include CONFIG_MX25 as several i.mx drivers handle the SoC
differences based on the this config option.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The woodburn board is based on the MX35 SOC.
Support for both external (NOR) and internal
(SD Card) boot mode are added. It uses the
generic SPL framework to implement the internal boot
mode.
The following peripherals are supported:
- Ethernet (FEC)
- SD Card
- NAND (512 MB)
- NOR Flash
In the internal boot mode, a simple imximage header
is generated to set the address in internal RAM
where the SOC must copy the SPL code. The initial setup
is then demanded to the SPL itself.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The patch adds SPL for the arm1136 architecture and
inserts SPL (the produced binary) to clobber target
in the main Makefile.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch modifies start.S for the arm1136 to make it
conform to start.S in armv7 architecture, to make it
usable if the SPL framework is used.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Patch fix warnings compiling with ELDK-4.2:
clock.c: In function 'get_standard_pll_sel_clk':
clock.c:341: warning: 'freq' may be used uninitialized in this function
Reported-by : Marek Vasut <marex@denx.de>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add targets of am335x_evm_uart{1,2,3,4,5} to have serial input/output on
UART{1,2,3,4,5} for use with the Beaglebone RS232 cape, am335x_evm
daughterboard, and other custom configurations.
Modify target for am335x_evm to include SERIAL1 and CONS_INDEX=1
options in order to clarify UART selection requirements.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or on the am335x_evm daughterboard, enable the proper pin-muxing.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or the am335x_evm daughterboard, enable the required clocks for
the UART in use.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
This makes the FAT filesystem API more consistent with other block-based
filesystems. If in the future standard multi-filesystem commands such as
"ls" or "load" are implemented, having FAT work the same way as other
filesystems will be necessary.
Convert cmd_fat.c to the new API, so the code looks more like other files
implementing the same commands for other filesystems.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
cur_part_info.{name,type} are strings. So, we don't need to memset()
the entire thing, just put the NULL-termination in the first byte.
Add missing initialization of the bootable and uuid fields.
None of these fields are actually used by fat.c. However, since it
stores the entire disk_partition_t, we should make sure that all fields
are valid.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
A future patch will implement the more standard filesystem API
fat_set_blk_dev(). This API has no way to know which partition number
the partition represents. Equally, future DM rework will make the
concept of partition number harder to pass around.
So, simply remove cur_part_nr from fat.c; its only use is in a
diagnostic printf, and the context where it's printed should make it
obvious which partition is referred to anyway (since the partition ID
would come from the user command-line that caused it).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
serial_ns16550.c:222:1: warning: symbol 'eserial1_init' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_setbrg' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_getc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_tstc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_putc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_puts' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_init' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_setbrg' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_getc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_tstc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_putc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_puts' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_init' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_setbrg' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_getc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_tstc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_putc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_puts' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_init' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_setbrg' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_getc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_tstc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_putc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_puts' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
fsl_i2c.c:217:14: warning: symbol 'get_i2c_clock' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE
define. Finally, enable the options on the am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
D0/D1 Swapped or not is a board property, not anything specific to
the am33xx SoC, so add a custom define for it.
At the same time correct the bit handling for the swapped mode
(DPE0 should be cleared and SI/DPE1 set).
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Some GPIOs differ in the new revision board.
Previous revision are considered obsolete and
they will not anymore supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The mcx board was slightly modified and the pinmux must be updated.
There is no need to support the old board, that becomes obsolete.
Signed-off-by: Stefano Babic <sbabic@denx.de>
In order to support low power state, you must source kernel system
timers to persistent clock, available across suspend/resume. In case of
AM335x device, the only source we have is, RTC32K, available in
wakeup/always-on domain. Having said that, during validation it has
been observed that, RTC clock need couple of seconds delay to stabilize
the RTC OSC clock; and such a huge delay is not acceptable in kernel
especially during early init and also it will impact quick/fast boot
use-cases.
So, RTC32k OSC enable dependency has been shifted to
SPL/first-bootloader.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Add Freescale MCF54418TWR ColdFire development board support.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
Add MCF5441x CPU support.
The MCF5441x devices are a family of highly-integrated 32-bit
microprocessors based on the Version 4m ColdFire microarchitecture,
comprising of the V4 integer core, memory management unit(MMU) and
enchanced multiply-accumulate unit(EMAC).
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
Fix the following build warnings in cpu_init.c:
cpu_init.c: In function 'cpu_init_f':
cpu_init.c:47:9: warning: unused variable 'pll'
cpu_init.c:46:10: warning: unused variable 'fbcs'
cpu_init.c:44:10: warning: unused variable 'scm1'
Signed-off-by: Alison Wang <b18965@freescale.com>
Add support for the new kmvect1 board powered by the mpc8309 processor.
As this board is very similar to the existing suvd3, instead of adding a
new config header file, just add a new config option to suvd3.h
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support for Keymile boards based on mpc8309
(it would be only kmvect1 for now)
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This processor, though very similar to other members of the
PowerQUICC II Pro family (namely 8308, 8360 and 832x), provides
yet another feature set than any supported sibling.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Introduce a new configuration token CONFIG_MPC830x to be shared among
mpc8308 and mpc8309. Define it for existing 8308 boards, and refactor
existing common code so to make future introduction of 8309 simpler.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fabio Estevam
Stefano Babic
Albert ARIBAUD
Andrew Bradford
Stephen Warren
Kim Phillips
Peter Korsgaard
Tom Rini
Vaibhav Hiremath
Alison Wang
Gerlando Falauto