This gives boards flexibility to assign other than default addresses to each
DDR controller. For example, DDR controler 2 can have 0 as the base and DDR
controller 1 has higher memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The workaround has been updated to use a slightly different magic number.
Change from 0x00003000 to 0x30003000.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This is what we have done for the UTMI PHY on P3041/P5020. Then the PHY
initialization can be reused in kernel without “usb start” command.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Use QSGMII card PHY address as default SGMII card PHY address, QSGMII card
PHY address is variable depends on different slot.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes
interfaces for quad-port dual media capability. This driver supports SGMII
and QSGMII MAC mode. For now SGMII mode is tested.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Removed unused declare serdes_get_prtcl() which was no longer needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
- set proper compatible property name for mEMAC.
- fixed ft_fixup_port for dual-role mEMAC, which will lead to
MAC node disabled incorrectly.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1, Implemented board_ft_fman_fixup_port() to fix port for kernel.
2, Implemented fdt_fixup_board_enet() to fix node status of different
slots and interfaces.
3, Adding detection of slot present for XGMII interface.
4, There is no PHY for XFI, so removed related phy address settings.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When CONFIG_SYS_FSL_QORIQ_CHASSIS2 is not defined, QMAN frequency will not
be initialized, and QMAN will have a wrong frequency display.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160QDS shares the same platform as T4240QDS. T4160 is a low power
version of T4240, with eight e6500 cores, two DDR3 controllers, and
slightly different SerDes protocols.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Separate CONFIG_PPC_T4240 from board config file. Prepare to add more SoC
variants supported on the same board.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160 SoC is low power version of T4240. The T4160 combines eight dual
threaded Power Architecture e6500 cores and two memory complexes (CoreNet
platform cache and DDR3 memory controller) with the same high-performance
datapath acceleration, networking, and peripheral bus interfaces.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Protocols are constants. Fix arrays with const prefix.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The PIR parsing algorithm we used is not only for E6500. It applies to all
SoCs with chassis 2.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Use decimal and hexadecimal for protocol numbers. It helps to match with
SoC user manual.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4240 internal UTMI phy is different comparing to previous UTMI PHY
in P3041.
This patch adds USB 2.0 UTMI Dual PHY new memory map and enable it for
T4240.
The phy timing is very sensitive and moving the phy enable code to
cpu_init.c will not work.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4240 has voltage ID fuse. Read the fuse and configure the voltage
correctly. Core voltage has higher tolerance on over side than below.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Missing nodes of crypto, pme, etc in device tree is not a fatal error.
Setting up the qman portal should skip the missing node and continue
to finish the rest.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Should check if interleaving is enabled before using interleaving mode.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Update the timing table to support more rank density, based on the theory
that similar density DIMMs have similar clock adjust and write level start
timing. Update the timing for 1600 and 1866 MT/s. Tested with Micron
MT18JSF1G72AZ-1G9E1 DIMMs, iDIMM M3CN-4GMJ3C0C-M92.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Lane H on SerDes4 should be SATA2 instead of SATA1
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. fix 10G mac offset by plus 8;
2. add second 10G port info for FM1 & FM2 when init ethernet info;
3. fix 10G lanes name to match lane protocol table;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Reverse the bit sequence to set and display serdes clock frequency
correctly. The correct bit maps in BRDCFG2 are
0 1 2 3 4 5 6 7
S1RATE[1:0] S2RATE[1:0] S3RATE[1:0] S4RATE[1:0]
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The L1 D-cache on e6500 is write-through. This means that it's not
considered a good idea to have the L1 up and running if the L2 is
disabled. We don't actually *use* the L1 until after the L2 is
brought up on e6500, so go ahead and move the L1 enablement after
that code is done.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix ccsr_gur for corenet platform. Remove non-exist registers. Add fuse
status register.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Makes it a bit easier to see if we've properly set them. While
we're in there, modify the accesses to HDBCR0 and HDBCR1 to actually
use those definitions.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The bit positions for FMAN1 freq in RCW is different for B4860.
Also addded a case when FMAN1 frewuency is equal to systembus.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Coreboot provides a lot of useful timing information. Provide a facility
to add this to bootstage on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which allows a (file, function, line number) to be marked
in bootstage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Che-Liang Chiou <clchiou@chromium.org>
In a previous CL we added the bootstage_relocate(), which should be
called after malloc is initted. Now we call it on generic board.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Any pointers to name strings that were passed to bootstage_mark_name()
pre-relocation should be copied post-relocation so that they don't get
trashed as the original location of U-Boot is re-used for other
purposes.
This change introduces a new API call that should be called from
board_init_r() after malloc has been initted on any board that uses
bootstage.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some functions don't have a stub for when CONFIG_BOOTSTAGE is not defined.
Add one to avoid #ifdefs in the code when this is used in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Che-Liang Chiou <clchiou@chromium.org>
Reviewed-by: Tom Wai-Hong Tam <waihong@chromium.org>
While we don't want PCAT timers for timing, we want timer 2 so that we can
still make a beep. Re-purpose the PCAT driver for this, and enable it in
coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is no longer used since we prefer the more accurate TSC timer, so
remove the dead code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
Tidy up some old broken and unneeded implementations. These are not used
by coreboot or anything else now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Michael Spang <spang@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
This timer runs at a rate that can be calculated, well over 100MHz. It is
ideal for accurate timing and does not need interrupt servicing.
Tidy up some old broken and unneeded implementations at the same time.
To provide a consistent view of boot time, we use the same time
base as coreboot. Use the base timestamp supplied by coreboot
as U-Boot's base time.
Signed-off-by: Simon Glass <sjg@chromium.org>base
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'Starting linux' message appears twice in the code, but both call
through the same place. Unify these and add calls to bootstage to
mark the occasion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Spang <spang@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
panic_puts() can be called in early boot to display a message. It might
help with early debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Wai-Hong Tam <waihong@chromium.org>
Several files use the global_data pointer without declaring it. This works
because the declaration is currently a NOP. But still it is better to
fix this so that x86 lines up with other archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since we use CONFIG_SYS_GENERIC_BOARD on x86, we don't need this anymore.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
Since we don't have real-mode code now, we can remove this chunk of the link
script.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ pointed out that this code is no longer used. Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
Commit 1865286466 (Introduce generic link
section.h symbol files) changed the __bss_end symbol type from char[] to
ulong. This led to wrong relocation parameters which ended up in a not working
u-boot. Unfortunately this is not clear to see cause due to RAM aliasing we
may get a 'half-working' u-boot then.
Fix this by dereferencing the __bss_end symbol where needed.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
York Sun
Roy Zang
Shaohui Xie
Shengzhou Liu
Andy Fleming
Sandeep Singh
Tom Rini
Simon Glass
Doug Anderson
Andreas Bießmann