This adds support for the MV78230 based DS414 NAS by Synology. The
relevant bits have been extracted from the 'synogpl-5004-armadaxp'
package Synology kindly published, garnished with a fair amount of
trial-and-error.
Sadly, support is far from perfect. The major parts I have failed in
are SATA and XHCI support. Details about these and some other things
follow:
Device Tree
-----------
The device tree file armada-xp-synology-ds414.dts has been copied from
Linux and enhanced by recent U-Boot specific changes to
armada-xp-gp.dts.
SATA Support
------------
There is a Marvell 88SX7042 controller attached to PCIe which is
supported by Linux's sata_mv driver but sadly not U-Boot's sata_mv.
I'm not sure if extending the latter to support PCI devices is worth the
effort at all. Porting sata_mv from Linux exceeded my brain's
capacities. :(
XHCI Support
------------
There is an EtronTech EJ168A XHCI controller attached to PCIe which
drives the two rear USB3 ports. After a bit of playing around I managed
to get it recognized by xhci-pci, but never was able to access any
devices attached to it. Enabling it in ds414 board config shows that it
does not respond to commands for whatever reason. The (somewhat) bright
side to it is that it is not even supported in Synology's customized
U-Boot, but that also means nowhere to steal the relevant bits from.
EHCI Support
------------
This seems functional after issuing 'usb start'. At least it detects USB
storage devices, and IIRC reading from them was OK. OTOH Linux fails to
register the controller if 'usb start' wasn't given before in U-Boot.
According to Synology sources, this board seems to support USB device
(gadget?) mode. Though I didn't play around with it.
PCIe Support
------------
This is fine, but trying to gate the clocks of unused lanes will hang
PCI enum. In addition to that, pci_mvebu seems not to support DM_PCI.
DDR3 Training
-------------
Marvell/Synology uses eight PUPs instead of four. Does not look like
this is meant to be customized in mainline U-Boot at all. OTOH I have
no idea what a "PUP" actually is.
PEX Init
--------
Synology uses different values than mainline U-Boot with this patch:
pex_max_unit_get returns 2, pex_max_if_get returns 7 and
max_serdes_lines is set to 7. Not changing this seems to not have an
impact, although I'm not entirely sure it does not cause issues I am not
aware of.
Static Environment
------------------
This allows to boot stock Synology firmware at least. In order to be a
little more flexible when it comes to booting custom kernels, do not
only load zImage partition, but also rd.gz into memory. This way it is
possible to use about 7MB for kernel with piggyback initramfs.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds basic support for Marvell's MV78230 SoC which belongs to the
Armada XP series.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of calling board_sat_r_get() only for those boards providing the
satr11 value via I2C, call it for all boards and return static values
for those not using I2C.
In addition to that, make this a weak function to allow for board code
to override it.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Change some of the PEX configuration output lines from always output to
only ouput upon specific debug enabling.
This changes the SPL output from:
U-Boot SPL 2016.01-rc2-00037-g9353a7f (Dec 10 2015 - 10:27:42)
High speed PHY - Version: 2.1.5 (COM-PHY-V20)
Update Device ID PEX0782611ab
Update Device ID PEX1782611ab
Update Device ID PEX2782611ab
Update Device ID PEX3782611ab
Update Device ID PEX8782611ab
Update PEX Device ID 0x78260
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.4
DDR3 Training Sequence - Ended Successfully
to:
U-Boot SPL 2016.01-rc2-00037-g9353a7f-dirty (Dec 10 2015 - 10:32:04)
High speed PHY - Version: 2.1.5 (COM-PHY-V20)
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.4
DDR3 Training Sequence - Ended Successfully
Resulting in a little faster bootup time.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the dual core Armada XP variant, the
MV78260. It has some minor differences to the 4-core MV78460,
e.g. only 12 serdes lanes.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
Using board ID 0 is reserved for the non-Marvell "custom" boards. So
move the board ID's to reflect this.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
Instead of allocating space in the driver for the serdes
specification table, just allow the board file to set a pointer
to it. Also, allow the board to only specify the lanes that are
used instead of including unused lanes.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Functions that do not modify the pointer passed should declare it
as const.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.
This will be the new structure:
drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)
drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)
Signed-off-by: Stefan Roese <sr@denx.de>
This code is ported from the Marvell bin_hdr code into mainline
SPL U-Boot. It needs to be executed very early so that the devices
connected to the serdes PHY are configured correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
With the upcoming addition of the Armada 38x SPL support, which is not
compatible to the Armada XP SERDES init code, we need to introduce a new
directory infrastructure. So lets move the AXP serdes init code into
a new directory. This way the A38x code can be added in a clean way.
Signed-off-by: Stefan Roese <sr@denx.de>
Now that the mach-mvebu directory exists and is used by Armada XP we can
move the mvebu-common files into this directory as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Phil Sutter
Stefan Roese
Kevin Smith