Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 0ad7f0950a [ppc4xx: cleanup
default environment for AMCC boards] broke the default env for
many PPC4xx boards. The '\0' character got removed at the end
of some environment commands like "update". This patch adds the
missing '\0' characters again.
Signed-off-by: Stefan Roese <sr@denx.de>
Until now, the Sequoia RAM-booting image disabled NOR flash support
as this image was mainly created for NAND-only boards. This patch
now enables NOR flash support for this RAM-booting version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch removes the PPC4xx UART driver. Instead the common NS16550
driver is used, since all PPC4xx SoC's use this peripheral device.
The file 4xx_uart.c now only implements the UART clock calculation
function which also sets the SoC internal UART divisors.
All PPC4xx board config headers are changed to use this common NS16550
driver now.
Tested on these boards:
acadia, canyonlands, katmai, kilauea, sequoia, zeus
Signed-off-by: Stefan Roese <sr@denx.de>
None of the AMCC boards uses an embedded environment, so there is no
need to run "saveenv" after updating U-Boot. Drop the redundant
commands from the default environment.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves the PPC4xx specific I2C device driver into the I2C
drivers directory. All 4xx config headers are updated to include this
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Till now only the ranges in the ebc node are updated with the values
currently configured in the PPC4xx EBC controller. With this patch now
the NOR flash size is updated in the device tree blob as well. This is
done by scanning the compatible nodes "cfi-flash" and "jedec-flash"
for the correct chip select number.
This size fixup is enabled for all AMCC eval board right now. Other
4xx boards may want to enable it as well, if this problem with multiple
NOR FLASH sizes exists.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Using a separate "u-boot" environment variable allows to easily
specify different filenames for the update procedure. This is also in
line with many other board configurations defining an "update" script.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Using a separate "u-boot" environment variable allows to easily
specify different filenames for the update procedure. This is also in
line with many other board configurations defining an "update" script.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves the load addresses for kernel, fdt and ramdisk to higher
addresses (>= 16MB). This enables booting of bigger kernel images (e.g.
lockdep enabled).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes CONFIG_SYS_BOOTMAPSZ from 8MB to 16MB which is the
initial TLB on 40x PPC's in the Linux kernel. With this change even bigger
Linux kernels (> 8MB) can be booted.
This patch also sets CONFIG_SYS_BOOTM_LEN to 16MB (default 8MB) to enable
decompression of bigger images.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds another build target for the AMCC Sequoia PPC440EPx
eval board. This RAM-booting version is targeted for boards without
NOR FLASH (NAND booting) which need a possibility to initially
program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000)
configured to setup the SDRAM, this debugger can load this RAM-
booting image to the target address in SDRAM (in this case 0x1000000)
and start it there. Then U-Boot's standard NAND commands can be
used to program the NAND FLASH (e.g. "nand write ...").
Here the commands to load and start this image from the BDI2000:
440EPX>reset halt
440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin
440EPX>go 0x1000000
Please note that this image automatically scans for an already
initialized SDRAM TLB (detected by EPN=0). This TLB will not be
cleared. This TLB doesn't need to be TLB #0, this RAM-booting
version will detect it and preserve it. So booting via BDI2000
will work and booting with a complete different TLB init via
U-Boot works as well.
Signed-off-by: Stefan Roese <sr@denx.de>
All in-tree IBM/AMCC PPC4xx boards using the EMAC get this new CONFIG
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR
FLASH, UART, EEPROM and temperature sensor, along with a shared debug
port. The two 460GT's will communicate with each other via shared
memory, Gigabit Ethernet and x1 PCI-Express.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch series unifies the AMCC eval board ports by introducing
a common include header for all AMCC eval boards:
include/configs/amcc-common.h
This header now includes all common configuration options/defines which
are removed from the board specific headers.
The reason for this is ease of maintenance and unified look and feel
of all AMCC boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Mike Frysinger
Stefan Roese
Wolfgang Denk
Detlev Zundel
Ben Warren
Adam Graham
Jean-Christophe PLAGNIOL-VILLARD