Initial commit for PH1-Pro4 Ace and Sanji boards.
Note:
There are two variants for the Ace board in terms of the amount of
DDR memory; 1GB or 2GB.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This board has an EEPROM connected to the I2C channel 0 of the SoC.
Its slave address is 0x54.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It turned out that DDR channel 2 was not working on ProXstream2
Vodka board. Add the missing ACBLDR0 register setting to adjust
the delay between the clock lines and the address/command lines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_CMD_DDRMPHY_DUMP is enabled, the build fails.
Fixes: 93d92d46cd ("ARM: uniphier: add dump command for DDR Multi PHY registers")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The U-Boot proper building needs to descend arch/arm/mach-uniphier/dram
to build these commands.
Fixes: 93d92d46cd ("ARM: uniphier: add dump command for DDR Multi PHY registers")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This header is no longer used.
This is the last file in arch/arm/mach-uniphier/include/mach/.
At last, I've succeeded in eliminating the mach directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The UniPhier EHCI driver (drivers/usb/host/ehci-uniphier.c) does
nothing special but set the base address and handle reset/clock.
Since commit 4feefdcfe9 ("usb: add clock support for generic EHCI"),
the generic one (drivers/usb/host/ehci-generic.c) can do those, too.
We no longer need to stick to the dedicated driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This block provides clock and reset control for MIO (Media I/O)
hardware blocks such as USB2.0, SD card, eMMC, etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This block provides clock and reset control for peripherals such as
UART, I2C, IC card, etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is the initial commit for the UniPhier clock drivers.
Currently, only the Media I/O clock is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The USB boot code is too fat and complicated to be included in SPL
(at least for now). So, it was implemented as a separate project
(what we call USB-loader).
The expected boot sequence is as follows:
Boot ROM -> USB-loader -> SPL -> U-Boot proper
The USB-loader loads the SPL and U-Boot proper from a USB memory
onto the locked L2 cache. Then, SPL needs to copy the U-Boot proper
to DRAM, so this mode looks like a NOR boot from the view of SPL.
However, we want to distinguish between (genuine) NOR boot and USB
boot in some places.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
UniPhier SoCs are not equipped with dedicated on-chip SRAM. Instead,
locked outer cache is used as RAM area during the early boot stage
where DRAM is not ready yet. This effectively means MMU must be
always enabled while we are in SPL.
Currently, the SPL image for UniPhier SoCs contains the page table
statically defined at compile time. It has been a burden because the
16KB page table occupies a quarter memory footprint of the 64KB SPL
image.
Finally, there is no more room to implement new features in SPL.
Setting aside the NOR boot mode, this issue can be solved by creating
the page table onto RAM at run time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
No special reason for the current stack address 0x0ff08000.
Change it to 0x00100000 to simplify the init_page_table.
There are two types of SoCs in terms of the load address of SPL.
[1] PH1-sLD3, PH1-LD4, PH1-sLD8
SPL is loaded at 0x00040000-0x0004ffff
[2] PH1-Pro4, PH1-Pro5, ProXstream2, PH1-LD6b
SPL is loaded at 0x00100000-0x0010ffff
The new stack area (0x000f8000-0x00100000) should be safe for all the
cases.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some of PH1-Pro4 boards are equipped with larger amount of DRAM than
the reference board. Add UMC settings to support them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nand driver support for zynqmp. The Nand
controller used in ZynqMP is Arasan Nand Flash
controller.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warning]
Signed-off-by: Scott Wood <oss@buserror.net>
Add keystone net DT support for k2g evm.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The defconfig patch will enable the the SPL and NAND settings.
The update to Kconfig will allow the SPL to configured in and
built.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch removes the uart clock enable from serial driver & move it in the
board code.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Set up the debug UART early if enabled, so that it is ready to use.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Now that we have converted all x86 codes to DM PCI, drop pci_type1.c
which is only built for legacy PCI. Also per checkpatch.pl warning,
DEFINE_PCI_DEVICE_TABLE is now deprecated so drop that too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that all x86 codes have been converted to use proper DM PCI APIs,
it's time to disable the legacy compatible layer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
There are still two places in Quark's MRC codes that use the generic
legacy PCI APIs, but as we are phasing out these legacy APIs, switch
to use Quark's own PCI config routines.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have converted all x86 codes to use DM PCI APIs,
drop those legacy ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Drop legacy PCI APIs usage in pci_assign_irqs() as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Use pci_[read|write]_config intead of x86_pci_[read|write]_config.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
With recent DM PCI changes to vesa_fb driver, external graphics
card does not work any more. This is because: after setting the
function disable bit, IGD and SDVO devices will disappear in the
PCI configuration space. This however creates an inconsistent state
from a driver model PCI controller point of view, as these two PCI
devices are still attached to its parent's child device list as
maintained by the driver model. Some driver model PCI APIs like
dm_pci_find_class() used in the vesa_fb driver, are referring to
the list to speed up the finding process instead of re-enumerating
the whole PCI bus, so it gets the stale cached data which is wrong.
To fix this, manually remove these two devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Once we get udevice of IGD and SDVO, we can use its udevice to
access PCI configuration space with dm_pci_write_config32().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
So far disable_igd() does not have any return value, but we may need
that in the future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Now that we have irq router's udevice passed as a parameter, it's
time to start using the DM PCI API instead of those legacy ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
At present irq_router is declared as a static struct irq_router in
arch/x86/cpu/irq.c. Since it's a driver control block, it makes sense
to move it to a per driver priv. Adjust existing APIs to accept an
additional parameter of irq_router's udevice.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
There is no need to parse PCH's <reg> property as we have already
a DM PCI API dm_pci_get_bdf() that can handle this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
IOBASE is now obtained from PCH driver, drop this <io-base> property.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
asm/arch/gpio.h is not needed anymore as we get the GPIO base from
PCH driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
At present this GPIO driver still uses the legacy PCI API. Now that
we have proper PCH drivers we can use those to obtain the information
we need. While the device tree has nodes for the GPIO peripheral it is
not in the right place. It should be on the PCI bus as a sub-peripheral
of the PCH device.
Update the device tree files to show the GPIO controller within the PCH,
so that PCI access works as expected. This also adds '#address-cells'
and '#size-cells' to the PCH node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Implement get_gpio_base op for bd82x6x, pch7 and pch9 drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Spell out 'sbase' to 'spi_base' so that it looks clearer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
pch_get_version op was only used by the ich spi controller driver,
and does not really provide a good identification of pch controller
so far, since we see plenty of Intel PCH chipsets and one differs
from another a lot, which is not simply either a PCHV_7 or PCHV_9.
Now that ich spi controller driver was updated to not get such info
from pch, the pch_get_version op is useless now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Unprotecting SPI flash is now handled in the SPI controller driver,
via a call to the PCH driver. Drop the ad-hoc version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Unprotecting SPI flash is now handled in the SPI controller driver,
via a call to the PCH driver. Drop the ad-hoc version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
David Müller (ELSOFT AG)
Masahiro Yamada
Siva Durga Prasad Paladugu
Simon Glass
Mugunthan V N
Adam Ford
Vikas Manocha
Bin Meng
Thomas Chou