upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
106 lines
3.0 KiB
106 lines
3.0 KiB
The chosen node
|
|
---------------
|
|
The chosen node does not represent a real device, but serves as a place
|
|
for passing data like which serial device to used to print the logs etc
|
|
|
|
|
|
stdout-path property
|
|
--------------------
|
|
Device trees may specify the device to be used for boot console output
|
|
with a stdout-path property under /chosen.
|
|
|
|
Example
|
|
-------
|
|
/ {
|
|
chosen {
|
|
stdout-path = "/serial@f00:115200";
|
|
};
|
|
|
|
serial@f00 {
|
|
compatible = "vendor,some-uart";
|
|
reg = <0xf00 0x10>;
|
|
};
|
|
};
|
|
|
|
tick-timer property
|
|
-------------------
|
|
In a system there are multiple timers, specify which timer to be used
|
|
as the tick-timer. Earlier it was hardcoded in the timer driver now
|
|
since device tree has all the timer nodes. Specify which timer to be
|
|
used as tick timer.
|
|
|
|
Example
|
|
-------
|
|
/ {
|
|
chosen {
|
|
tick-timer = "/timer2@f00";
|
|
};
|
|
|
|
timer2@f00 {
|
|
compatible = "vendor,some-timer";
|
|
reg = <0xf00 0x10>;
|
|
};
|
|
};
|
|
|
|
u-boot,spl-boot-order property
|
|
------------------------------
|
|
|
|
In a system using an SPL stage and having multiple boot sources
|
|
(e.g. SPI NOR flash, on-board eMMC and a removable SD-card), the boot
|
|
device may be probed by reading the image and verifying an image
|
|
signature.
|
|
|
|
If the SPL is configured through the device-tree, the boot-order can
|
|
be configured with the spl-boot-order property under the /chosen node.
|
|
Each list element of the property should specify a device to be probed
|
|
in the order they are listed: references (i.e. implicit paths), a full
|
|
path or an alias is expected for each entry.
|
|
|
|
A special specifier "same-as-spl" can be used at any position in the
|
|
boot-order to direct U-Boot to insert the device the SPL was booted
|
|
from there. Whether this is indeed inserted or silently ignored (if
|
|
it is not supported on any given SoC/board or if the boot-device is
|
|
not available to continue booting from) is implementation-defined.
|
|
Note that if "same-as-spl" expands to an actual node for a given
|
|
board, the corresponding node may appear multiple times in the
|
|
boot-order (as there currently exists no mechanism to suppress
|
|
duplicates from the list).
|
|
|
|
Example
|
|
-------
|
|
/ {
|
|
chosen {
|
|
u-boot,spl-boot-order = "same-as-spl", &sdmmc, "/sdhci@fe330000";
|
|
};
|
|
};
|
|
|
|
u-boot,spl-boot-device property
|
|
-------------------------------
|
|
|
|
This property is a companion-property to the u-boot,spl-boot-order and
|
|
will be injected automatically by the SPL stage to notify a later stage
|
|
of where said later stage was booted from.
|
|
|
|
You should not define this property yourself in the device-tree, as it
|
|
may be overwritten without warning.
|
|
|
|
firmware-loader property
|
|
------------------------
|
|
Multiple file system firmware loader nodes could be defined in device trees for
|
|
multiple storage type and their default partition, then a property
|
|
"firmware-loader" can be used to pass default firmware loader
|
|
node(default storage type) to the firmware loader driver.
|
|
|
|
Example
|
|
-------
|
|
/ {
|
|
chosen {
|
|
firmware-loader = &fs_loader0;
|
|
};
|
|
|
|
fs_loader0: fs-loader@0 {
|
|
u-boot,dm-pre-reloc;
|
|
compatible = "u-boot,fs-loader";
|
|
phandlepart = <&mmc 1>;
|
|
};
|
|
};
|
|
|