upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
556 lines
11 KiB
556 lines
11 KiB
/*
|
|
* (C) Copyright 2014
|
|
* Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <hwconfig.h>
|
|
#include <i2c.h>
|
|
#include <spi.h>
|
|
#include <libfdt.h>
|
|
#include <fdt_support.h>
|
|
#include <pci.h>
|
|
#include <mpc83xx.h>
|
|
#include <fsl_esdhc.h>
|
|
#include <asm/io.h>
|
|
#include <asm/fsl_serdes.h>
|
|
#include <asm/fsl_mpc83xx_serdes.h>
|
|
|
|
#include "mpc8308.h"
|
|
|
|
#include <gdsys_fpga.h>
|
|
|
|
#include "../common/adv7611.h"
|
|
#include "../common/ch7301.h"
|
|
#include "../common/dp501.h"
|
|
#include "../common/ioep-fpga.h"
|
|
#include "../common/mclink.h"
|
|
#include "../common/osd.h"
|
|
#include "../common/phy.h"
|
|
#include "../common/fanctrl.h"
|
|
|
|
#include <pca953x.h>
|
|
#include <pca9698.h>
|
|
|
|
#include <miiphy.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define MAX_MUX_CHANNELS 2
|
|
|
|
enum {
|
|
MCFPGA_DONE = 1 << 0,
|
|
MCFPGA_INIT_N = 1 << 1,
|
|
MCFPGA_PROGRAM_N = 1 << 2,
|
|
MCFPGA_UPDATE_ENABLE_N = 1 << 3,
|
|
MCFPGA_RESET_N = 1 << 4,
|
|
};
|
|
|
|
enum {
|
|
GPIO_MDC = 1 << 14,
|
|
GPIO_MDIO = 1 << 15,
|
|
};
|
|
|
|
unsigned int mclink_fpgacount;
|
|
struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;
|
|
|
|
struct {
|
|
u8 bus;
|
|
u8 addr;
|
|
} strider_fans[] = CONFIG_STRIDER_FANS;
|
|
|
|
int fpga_set_reg(u32 fpga, u16 *reg, off_t regoff, u16 data)
|
|
{
|
|
int res;
|
|
|
|
switch (fpga) {
|
|
case 0:
|
|
out_le16(reg, data);
|
|
break;
|
|
default:
|
|
res = mclink_send(fpga - 1, regoff, data);
|
|
if (res < 0) {
|
|
printf("mclink_send reg %02lx data %04x returned %d\n",
|
|
regoff, data, res);
|
|
return res;
|
|
}
|
|
break;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
int fpga_get_reg(u32 fpga, u16 *reg, off_t regoff, u16 *data)
|
|
{
|
|
int res;
|
|
|
|
switch (fpga) {
|
|
case 0:
|
|
*data = in_le16(reg);
|
|
break;
|
|
default:
|
|
if (fpga > mclink_fpgacount)
|
|
return -EINVAL;
|
|
res = mclink_receive(fpga - 1, regoff, data);
|
|
if (res < 0) {
|
|
printf("mclink_receive reg %02lx returned %d\n",
|
|
regoff, res);
|
|
return res;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
char *s = env_get("serial#");
|
|
bool hw_type_cat = pca9698_get_value(0x20, 18);
|
|
|
|
puts("Board: ");
|
|
|
|
printf("Strider %s", hw_type_cat ? "CAT" : "Fiber");
|
|
|
|
if (s != NULL) {
|
|
puts(", serial# ");
|
|
puts(s);
|
|
}
|
|
|
|
puts("\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
int last_stage_init(void)
|
|
{
|
|
int slaves;
|
|
unsigned int k;
|
|
unsigned int mux_ch;
|
|
unsigned char mclink_controllers_dvi[] = { 0x3c, 0x3d, 0x3e };
|
|
#ifdef CONFIG_STRIDER_CPU
|
|
unsigned char mclink_controllers_dp[] = { 0x24, 0x25, 0x26 };
|
|
#endif
|
|
bool hw_type_cat = pca9698_get_value(0x20, 18);
|
|
#ifdef CONFIG_STRIDER_CON_DP
|
|
bool is_dh = pca9698_get_value(0x20, 25);
|
|
#endif
|
|
bool ch0_sgmii2_present = false;
|
|
|
|
/* Turn on Analog Devices ADV7611 */
|
|
pca9698_direction_output(0x20, 8, 0);
|
|
|
|
/* Turn on Parade DP501 */
|
|
pca9698_direction_output(0x20, 10, 1);
|
|
pca9698_direction_output(0x20, 11, 1);
|
|
|
|
ch0_sgmii2_present = !pca9698_get_value(0x20, 37);
|
|
|
|
/* wait for FPGA done, then reset FPGA */
|
|
for (k = 0; k < ARRAY_SIZE(mclink_controllers_dvi); ++k) {
|
|
unsigned int ctr = 0;
|
|
unsigned char *mclink_controllers = mclink_controllers_dvi;
|
|
|
|
#ifdef CONFIG_STRIDER_CPU
|
|
if (i2c_probe(mclink_controllers[k])) {
|
|
mclink_controllers = mclink_controllers_dp;
|
|
if (i2c_probe(mclink_controllers[k]))
|
|
continue;
|
|
}
|
|
#else
|
|
if (i2c_probe(mclink_controllers[k]))
|
|
continue;
|
|
#endif
|
|
while (!(pca953x_get_val(mclink_controllers[k])
|
|
& MCFPGA_DONE)) {
|
|
udelay(100000);
|
|
if (ctr++ > 5) {
|
|
printf("no done for mclink_controller %d\n", k);
|
|
break;
|
|
}
|
|
}
|
|
|
|
pca953x_set_dir(mclink_controllers[k], MCFPGA_RESET_N, 0);
|
|
pca953x_set_val(mclink_controllers[k], MCFPGA_RESET_N, 0);
|
|
udelay(10);
|
|
pca953x_set_val(mclink_controllers[k], MCFPGA_RESET_N,
|
|
MCFPGA_RESET_N);
|
|
}
|
|
|
|
if (hw_type_cat) {
|
|
int retval;
|
|
struct mii_dev *mdiodev = mdio_alloc();
|
|
if (!mdiodev)
|
|
return -ENOMEM;
|
|
strncpy(mdiodev->name, bb_miiphy_buses[0].name, MDIO_NAME_LEN);
|
|
mdiodev->read = bb_miiphy_read;
|
|
mdiodev->write = bb_miiphy_write;
|
|
|
|
retval = mdio_register(mdiodev);
|
|
if (retval < 0)
|
|
return retval;
|
|
for (mux_ch = 0; mux_ch < MAX_MUX_CHANNELS; ++mux_ch) {
|
|
if ((mux_ch == 1) && !ch0_sgmii2_present)
|
|
continue;
|
|
|
|
setup_88e1514(bb_miiphy_buses[0].name, mux_ch);
|
|
}
|
|
}
|
|
|
|
/* give slave-PLLs and Parade DP501 some time to be up and running */
|
|
udelay(500000);
|
|
|
|
mclink_fpgacount = CONFIG_SYS_MCLINK_MAX;
|
|
slaves = mclink_probe();
|
|
mclink_fpgacount = 0;
|
|
|
|
ioep_fpga_print_info(0);
|
|
|
|
if (!adv7611_probe(0))
|
|
printf(" Advantiv ADV7611 HDMI Receiver\n");
|
|
|
|
#ifdef CONFIG_STRIDER_CON
|
|
if (ioep_fpga_has_osd(0))
|
|
osd_probe(0);
|
|
#endif
|
|
|
|
#ifdef CONFIG_STRIDER_CON_DP
|
|
if (ioep_fpga_has_osd(0)) {
|
|
osd_probe(0);
|
|
if (is_dh)
|
|
osd_probe(4);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_STRIDER_CPU
|
|
ch7301_probe(0, false);
|
|
dp501_probe(0, false);
|
|
#endif
|
|
|
|
if (slaves <= 0)
|
|
return 0;
|
|
|
|
mclink_fpgacount = slaves;
|
|
|
|
#ifdef CONFIG_STRIDER_CPU
|
|
/* get ADV7611 out of reset, power up DP501, give some time to wakeup */
|
|
for (k = 1; k <= slaves; ++k)
|
|
FPGA_SET_REG(k, extended_control, 0x10); /* enable video */
|
|
|
|
udelay(500000);
|
|
#endif
|
|
|
|
for (k = 1; k <= slaves; ++k) {
|
|
ioep_fpga_print_info(k);
|
|
#ifdef CONFIG_STRIDER_CON
|
|
if (ioep_fpga_has_osd(k))
|
|
osd_probe(k);
|
|
#endif
|
|
#ifdef CONFIG_STRIDER_CON_DP
|
|
if (ioep_fpga_has_osd(k)) {
|
|
osd_probe(k);
|
|
if (is_dh)
|
|
osd_probe(k + 4);
|
|
}
|
|
#endif
|
|
#ifdef CONFIG_STRIDER_CPU
|
|
if (!adv7611_probe(k))
|
|
printf(" Advantiv ADV7611 HDMI Receiver\n");
|
|
ch7301_probe(k, false);
|
|
dp501_probe(k, false);
|
|
#endif
|
|
if (hw_type_cat) {
|
|
int retval;
|
|
struct mii_dev *mdiodev = mdio_alloc();
|
|
if (!mdiodev)
|
|
return -ENOMEM;
|
|
strncpy(mdiodev->name, bb_miiphy_buses[k].name,
|
|
MDIO_NAME_LEN);
|
|
mdiodev->read = bb_miiphy_read;
|
|
mdiodev->write = bb_miiphy_write;
|
|
|
|
retval = mdio_register(mdiodev);
|
|
if (retval < 0)
|
|
return retval;
|
|
setup_88e1514(bb_miiphy_buses[k].name, 0);
|
|
}
|
|
}
|
|
|
|
for (k = 0; k < ARRAY_SIZE(strider_fans); ++k) {
|
|
i2c_set_bus_num(strider_fans[k].bus);
|
|
init_fan_controller(strider_fans[k].addr);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* provide access to fpga gpios (for I2C bitbang)
|
|
* (these may look all too simple but make iocon.h much more readable)
|
|
*/
|
|
void fpga_gpio_set(unsigned int bus, int pin)
|
|
{
|
|
FPGA_SET_REG(bus, gpio.set, pin);
|
|
}
|
|
|
|
void fpga_gpio_clear(unsigned int bus, int pin)
|
|
{
|
|
FPGA_SET_REG(bus, gpio.clear, pin);
|
|
}
|
|
|
|
int fpga_gpio_get(unsigned int bus, int pin)
|
|
{
|
|
u16 val;
|
|
|
|
FPGA_GET_REG(bus, gpio.read, &val);
|
|
|
|
return val & pin;
|
|
}
|
|
|
|
#ifdef CONFIG_STRIDER_CON_DP
|
|
void fpga_control_set(unsigned int bus, int pin)
|
|
{
|
|
u16 val;
|
|
|
|
FPGA_GET_REG(bus, control, &val);
|
|
FPGA_SET_REG(bus, control, val | pin);
|
|
}
|
|
|
|
void fpga_control_clear(unsigned int bus, int pin)
|
|
{
|
|
u16 val;
|
|
|
|
FPGA_GET_REG(bus, control, &val);
|
|
FPGA_SET_REG(bus, control, val & ~pin);
|
|
}
|
|
#endif
|
|
|
|
void mpc8308_init(void)
|
|
{
|
|
pca9698_direction_output(0x20, 26, 1);
|
|
}
|
|
|
|
void mpc8308_set_fpga_reset(unsigned state)
|
|
{
|
|
pca9698_set_value(0x20, 26, state ? 0 : 1);
|
|
}
|
|
|
|
void mpc8308_setup_hw(void)
|
|
{
|
|
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
|
|
|
|
/*
|
|
* set "startup-finished"-gpios
|
|
*/
|
|
setbits_be32(&immr->gpio[0].dir, (1 << (31-11)) | (1 << (31-12)));
|
|
setbits_be32(&immr->gpio[0].dat, 1 << (31-12));
|
|
}
|
|
|
|
int mpc8308_get_fpga_done(unsigned fpga)
|
|
{
|
|
return pca9698_get_value(0x20, 20);
|
|
}
|
|
|
|
#ifdef CONFIG_FSL_ESDHC
|
|
int board_mmc_init(bd_t *bd)
|
|
{
|
|
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
|
|
sysconf83xx_t *sysconf = &immr->sysconf;
|
|
|
|
/* Enable cache snooping in eSDHC system configuration register */
|
|
out_be32(&sysconf->sdhccr, 0x02000000);
|
|
|
|
return fsl_esdhc_mmc_init(bd);
|
|
}
|
|
#endif
|
|
|
|
static struct pci_region pcie_regions_0[] = {
|
|
{
|
|
.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
|
|
.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
|
|
.size = CONFIG_SYS_PCIE1_MEM_SIZE,
|
|
.flags = PCI_REGION_MEM,
|
|
},
|
|
{
|
|
.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
|
|
.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
|
|
.size = CONFIG_SYS_PCIE1_IO_SIZE,
|
|
.flags = PCI_REGION_IO,
|
|
},
|
|
};
|
|
|
|
void pci_init_board(void)
|
|
{
|
|
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
|
|
sysconf83xx_t *sysconf = &immr->sysconf;
|
|
law83xx_t *pcie_law = sysconf->pcielaw;
|
|
struct pci_region *pcie_reg[] = { pcie_regions_0 };
|
|
|
|
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
|
|
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
|
|
|
|
/* Deassert the resets in the control register */
|
|
out_be32(&sysconf->pecr1, 0xE0008000);
|
|
udelay(2000);
|
|
|
|
/* Configure PCI Express Local Access Windows */
|
|
out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
|
|
out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
|
|
|
|
mpc83xx_pcie_init(1, pcie_reg);
|
|
}
|
|
|
|
ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
|
|
{
|
|
info->portwidth = FLASH_CFI_16BIT;
|
|
info->chipwidth = FLASH_CFI_BY16;
|
|
info->interface = FLASH_CFI_X16;
|
|
return 1;
|
|
}
|
|
|
|
#if defined(CONFIG_OF_BOARD_SETUP)
|
|
int ft_board_setup(void *blob, bd_t *bd)
|
|
{
|
|
ft_cpu_setup(blob, bd);
|
|
fsl_fdt_fixup_dr_usb(blob, bd);
|
|
fdt_fixup_esdhc(blob, bd);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* FPGA MII bitbang implementation
|
|
*/
|
|
|
|
struct fpga_mii {
|
|
unsigned fpga;
|
|
int mdio;
|
|
} fpga_mii[] = {
|
|
{ 0, 1},
|
|
{ 1, 1},
|
|
{ 2, 1},
|
|
{ 3, 1},
|
|
};
|
|
|
|
static int mii_dummy_init(struct bb_miiphy_bus *bus)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
static int mii_mdio_active(struct bb_miiphy_bus *bus)
|
|
{
|
|
struct fpga_mii *fpga_mii = bus->priv;
|
|
|
|
if (fpga_mii->mdio)
|
|
FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
|
|
else
|
|
FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mii_mdio_tristate(struct bb_miiphy_bus *bus)
|
|
{
|
|
struct fpga_mii *fpga_mii = bus->priv;
|
|
|
|
FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mii_set_mdio(struct bb_miiphy_bus *bus, int v)
|
|
{
|
|
struct fpga_mii *fpga_mii = bus->priv;
|
|
|
|
if (v)
|
|
FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
|
|
else
|
|
FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
|
|
|
|
fpga_mii->mdio = v;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mii_get_mdio(struct bb_miiphy_bus *bus, int *v)
|
|
{
|
|
u16 gpio;
|
|
struct fpga_mii *fpga_mii = bus->priv;
|
|
|
|
FPGA_GET_REG(fpga_mii->fpga, gpio.read, &gpio);
|
|
|
|
*v = ((gpio & GPIO_MDIO) != 0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mii_set_mdc(struct bb_miiphy_bus *bus, int v)
|
|
{
|
|
struct fpga_mii *fpga_mii = bus->priv;
|
|
|
|
if (v)
|
|
FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDC);
|
|
else
|
|
FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDC);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mii_delay(struct bb_miiphy_bus *bus)
|
|
{
|
|
udelay(1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
struct bb_miiphy_bus bb_miiphy_buses[] = {
|
|
{
|
|
.name = "board0",
|
|
.init = mii_dummy_init,
|
|
.mdio_active = mii_mdio_active,
|
|
.mdio_tristate = mii_mdio_tristate,
|
|
.set_mdio = mii_set_mdio,
|
|
.get_mdio = mii_get_mdio,
|
|
.set_mdc = mii_set_mdc,
|
|
.delay = mii_delay,
|
|
.priv = &fpga_mii[0],
|
|
},
|
|
{
|
|
.name = "board1",
|
|
.init = mii_dummy_init,
|
|
.mdio_active = mii_mdio_active,
|
|
.mdio_tristate = mii_mdio_tristate,
|
|
.set_mdio = mii_set_mdio,
|
|
.get_mdio = mii_get_mdio,
|
|
.set_mdc = mii_set_mdc,
|
|
.delay = mii_delay,
|
|
.priv = &fpga_mii[1],
|
|
},
|
|
{
|
|
.name = "board2",
|
|
.init = mii_dummy_init,
|
|
.mdio_active = mii_mdio_active,
|
|
.mdio_tristate = mii_mdio_tristate,
|
|
.set_mdio = mii_set_mdio,
|
|
.get_mdio = mii_get_mdio,
|
|
.set_mdc = mii_set_mdc,
|
|
.delay = mii_delay,
|
|
.priv = &fpga_mii[2],
|
|
},
|
|
{
|
|
.name = "board3",
|
|
.init = mii_dummy_init,
|
|
.mdio_active = mii_mdio_active,
|
|
.mdio_tristate = mii_mdio_tristate,
|
|
.set_mdio = mii_set_mdio,
|
|
.get_mdio = mii_get_mdio,
|
|
.set_mdc = mii_set_mdc,
|
|
.delay = mii_delay,
|
|
.priv = &fpga_mii[3],
|
|
},
|
|
};
|
|
|
|
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
|
|
sizeof(bb_miiphy_buses[0]);
|
|
|