Add macros for the DIV6P1 clock type, which is used on Gen2
and optionally also on Gen3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull code which is common for RCar Gen2 and RCar Gen3 into
separate source file. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add Kconfig entries for each SoC clock table, so they can be
compiled in or out at build time. This can reduce the size of
the binary if desired.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Gen2 requires setting RMSTPCR before booting, while on Gen3 this
is thus far always zero. Split the tables so the RMSTPCR can be set
too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Extract the macros specific to Gen3 clock into a separate header.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not all SoCs have the same PLL configuration options,
so make those PLL configuraion tables per-SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not all drivers use the same IDs, so make those IDs per-driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Split the massive driver into smaller per-SoC drivers and pull the
common code into a separate file. This would allow configuring out
unnecessary clock drivers once the Kconfig changes are in and also
allow adding more clock tables easily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use the common RCAR_GEN2 config option instead of enumerating
each SoC and having a lengthy ifdef clause. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Replace fdtdec_get_addr() with devfdt_get_addr() as the later one is
the current recommended practice.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Convert these configuration options to Kconfig, update board defconfigs
and drop them from whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull out u-boot extras into dtsi files to make synchronization of DTS
from Linux kernel as easy as a simple copy. All the U-Boot extras are
now in *-u-boot.dts* files instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.14,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add macro QIXIS_LBMAP_EMMC, QIXIS_LBMAP_IFC, QIXIS_RCW_SRC_IFC,
QIXIS_RCW_SRC_EMMC to enable IFC and eMMC as boot sources for
qixis commands.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[YS: Modify subject and add commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Currently only SD, NAND can be secondary boot sources controlled
by FPGA/CPLD via qixis commands. For SoC like LS1088 IFC-NOR
can be secondary boot source, while QSPI-NOR is the primary.
Add options in qixis to switch to other boot sources including
ifc and emmc.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The hash command function were not flushing the dcache before passing data
to CAAM/DMA and not invalidating the dcache when getting data back.
Due the data cache incoherency, HW accelerated hash commands used to fail
with CAAM errors like "Invalid KEY Command".
Check if pbuf and pout buffers are properly aligned to the cache line size
and flush/invalidate the memory regions to address this issue.
This solution is based in a previous work from Clemens Gruber in
commit 598e9dccc7 ("crypto/fsl: fix BLOB encapsulation and
decapsulation")
Reported-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The current GPL only licensing on the device trees makes it very
impractical for other software components licensed under another
license.
To make it easier to reuse them, re-license the the device trees for
Freescale (now NXP) SoCs and boards under GPLv2+/X11 dual license.
Same trend is followed in linux.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enables and compiles VID specific functions for SPL.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting
the voltage via LTC3882 regulator.
This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by
disabling the SERDES, changing the SVDD and then re-enabling SERDES.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds a VID specific API in init_sequence_f and spl code flow
namely init_func_vid which is required to adjust core voltage.
VID specific code is required in spl, hence moving flag CONFIG_VID
out of spl flags.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When VID feature is supported, check the contents of fuse register
and configure DDR operate at 0.9v.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sets DDR configuration parameter cdr1 before all other settings
to support case 0.9v VDD is enabled for some SoCs
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Restructures common driver to support LTC3882 voltage regulator
chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moves IR chip (IR36021) specific code in flag to resolve
compilation issue where it is not present. For example,
LS1088A is having a new LTC3882 voltage chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds a board specific API namely board_adjust_vdd which
is required to define the board VDD adjust settings.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds SERDES voltage and reset SERDES lanes API and makes
enable/disable DDR controller support 0.9V API common.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This time around we have a lot of EFI patches from Heinrich.
Highlights are:
- Allow EFI applications to register as drivers
- Allow exposure of U-Boot block devices from an EFI payload
- Compatibility improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJaZwoHAAoJECszeR4D/txgKU0QAMRg5zm95ClGRBjxVbAW7M73
T7pHQBbsoaddfK0zOAltLo5wOLhLNJPb93L0gxjChx6o5PDV6iFISAYRnJiQsVyj
XI5Ve2XV8DRBMdaKVxeq1Z7syjYllhdkzBeQbitw6TfIDy+qeA/x/Z1Jz6gYnTDh
ZmbP0HrTk59Vg80ZLa4XcBumqesfBnUAEDFx9sYX9T8/7bx3QWQfwAJ3XHYKkDmM
aaXFq/02/z0ZgDPinkG00AIkKme+QRAFCd+leACkDGPR9pAC4mf6df/006a0Sl/s
qw5j5J06yOZ0ykTxwmREsGg62IqCTPA51mSiBvWS37vZeUUO0WhyysuUvQ5YVv+U
UII5YN/0PGVGVZ4hM1s3yEijEf48n1YncASRyYVfCtJjC/WJ2IUlthH85MEBrrn4
IqVHeoLJg5/a3T2Tdo83q/AD9saFshaVsT42C04JB07/29SKjNjZ9sUMMBatOlAP
HleCy3jgodwB4kF1Tld6oeakvuc0xOhCOckD3rWUhsi9eN9liZiv7AlXFiXxPUgz
tWcJtluaZ/vhXXJWdCqwf2KIq0fmawgBUsSwLByPrZKTp9OojGsA52Ro6jAuu2Mq
vKqZhRpSF7DtAhALcex5V2uwCc5npehTTXIHYG/bmzBQWrEWfBlYA7dSjMiuQbuD
0+1EicqsGp8Chr1H37bC
=XZ4q
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-01-23
This time around we have a lot of EFI patches from Heinrich.
Highlights are:
- Allow EFI applications to register as drivers
- Allow exposure of U-Boot block devices from an EFI payload
- Compatibility improvements
This converts the following to Kconfig:
CONFIG_SOC_DA8XX
CONFIG_SOC_DA850
CONFIG_DA850_LOWLEVEL
CONFIG_MACH_DAVINCI_DA850_EVM
CONFIG_SYS_DA850_PLL_INIT
CONFIG_SYS_DA850_DDR_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: David Lechner <david@lechnology.com>
[trini: Rework CONFIG_SYS_DA850_PLL_INIT so it's selected on SOC_DA8XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some messages are only useful if an error occurs.
Fix a use after free.
Add a missing free.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Create device path nodes for UCLASS_ETH udevices.
Create device path nodes of block device children of UCLASS_MMC udevices.
Consistently use debug for unsupported nodes.
Set the log level to error.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Fix build failure by adding #ifdef CONFIG_DM_ETH]
Signed-off-by: Alexander Graf <agraf@suse.de>
This test checks the driver for block IO devices.
A disk image is created in memory.
A handle is created for the new block IO device.
The block I/O protocol is installed on the handle.
ConnectController is used to setup partitions and to install the simple
file protocol.
A known file is read from the file system and verified.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides
* a uclass for EFI drivers
* a EFI driver for block devices
For each EFI driver the uclass
* creates a handle
* adds the driver binding protocol
The uclass provides the bind, start, and stop entry points for the driver
binding protocol.
In bind() and stop() it checks if the controller implements the protocol
supported by the EFI driver. In the start() function it calls the bind()
function of the EFI driver. In the stop() function it destroys the child
controllers.
The EFI block driver binds to controllers implementing the block io
protocol.
When the bind function of the EFI block driver is called it creates a
new U-Boot block device. It installs child handles for all partitions and
installs the simple file protocol on these.
The read and write functions of the EFI block driver delegate calls to the
controller that it is bound to.
A usage example is as following:
U-Boot loads the iPXE snp.efi executable. iPXE connects an iSCSI drive and
exposes a handle with the block IO protocol. It calls ConnectController.
Now the EFI block driver installs the partitions with the simple file
protocol.
iPXE uses the simple file protocol to load Grub or the Linux Kernel.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: add comment on calloc len]
Signed-off-by: Alexander Graf <agraf@suse.de>
The device tree is needed at runtime. So we have to store it in
EFI_RUNTIME_SERVICES_DATA memory.
The UEFI spec recommends to store all configuration tables in
EFI_RUNTIME_SERVICES_DATA memory.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This pair of tests checks the StartImage boot service.
Each test loads an EFI application into memory and starts it.
One returns by calling the Exit boot service. The other returns directly.
The tests are not built on x86_64 because the relocation code for the efi
binary cannot be created.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch lets the implementation of ExitBootServices conform to
the UEFI standard.
The timer events must be disabled before calling the notification
functions of the exit boot services events.
The boot services must be disabled in the system table.
The handles in the system table should be defined as efi_handle_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In ExitBootServices we need to signal events irrespective of the current
TPL level. A new parameter check_tpl is added to efi_signal_event().
Function efi_console_timer_notify() gets some comments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Marek Vasut
Chris Brandt
Tom Rini
Ashish Kumar
Breno Lima
Pankaj Bansal
Rajesh Bhagat
Adam Ford
Heinrich Schuchardt