Add infrastructure for ICID setup and device tree fixup on ARM
platforms. This include basic ICID setup for several devices.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a define with a value for the missing debug stream ID.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QMAN_BAR{E} register setup was disabled on ARM platforms, however the
register does need to be set. Enable the code also on ARMs and fix the
CONFIG_SYS_QMAN_MEM_PHYS define to the correct value so that the newly
enabled code works.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QMan IP block in this SoC is version 3.2 so advertise
this in the SoC configuration header.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add defines for the edma and qdma register block base addresses.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The 16 char ethernet name size is inadequate to hold the name of ethernet
name "DPMAC17@rgmii-id", which is a valid name in LX2160AQDS/LX2160ARDB.
Therefore, increase the name string size to 20 chars.
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Ioana Ciocoi Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The ethernet name should be within the ETH_NAME_LEN, as this
is the buffer space allocated to ethernet name.
Otherwise, this causes buffer overflow.
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Most FSL PCIe controllers expects 333 MHz PCI reference clock.
This clock is derived from the CCB but in many cases the ref.
clock is not 333 MHz and a divisor needs to be configured.
This adds PEX_CCB_DIV #define which can be defined for each
type of CPU/platform.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In ft_fixup_enet_phy_connect_type(), use strlen() instead of sizeof()
on the pointer result of phy_string_for_interface(). sizeof() was
returning the size of the pointer (4 bytes), resulting in the
phy-connection-type being set to "rgmi" rather than "rgmii-id".
Signed-off-by: Brendan Shanks <brendan.shanks@teradek.com>
Cc: York Sun <york.sun@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add command "boot_bank X" to switch the boot bank to either 1 or 2.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the PCA9646 support, which is 2-wire bus switch and buffered 4-channel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This is to test power_domain_on in device_probe.
If the device has a power-domain property, enable it
when probe the device. So add the test to check
whether it is powered on or not.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add CONFIG_SPL_POWER_DOMAIN config entry.
Build drivers/power/domain if this config is selected.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add dummy functions when CONFIG_POWER_DOMAIN not defined.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The Assigned Clock parents and rates misses the fact that a "0" entry can
be passed to skip setting a parent or rate of an assigned clock as
described in the Linux clock bindings at [1].
This patch simply skips the clock reparenting if the DT parsing returns
-ENOENT and the clock rate setting if "0" is passed as clock rate.
[1] https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/clock/clock-bindings.txt#L135
Fixes: f4fcba5c5b "clk: implement clk_set_defaults()"
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As platform uses GPIOs for card detection, it's
simpler and more readable to use GPIO_ACTIVE_(LOW|HIGH)
in the gpio flags instead of using the cd-inverted
property.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add missing clk_free() call in case of failure
when enabling the clock.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Config flag CONFIG_BLK becomes mandatory, update arm_pl180_mmci
to support this config.
This driver is used by STM32Fx and by Vexpress platforms.
Only STM32Fx are DM ready. No DM code is isolated and will be
removed easily when wexpress will be converted to DM.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
CONFIG_BLK config flag becomes mandatory, enable it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
1947c2d2a0 introduces cache line flushes for the bootcounter, but if
the start address is not aligned then the flush causes warnings of
the form:
CACHE: Misaligned operation at range [4030b7fc, 4030b83c]
Align both the start and end of the buffer (possibly crossing multiple
lines).
Fixes: 1947c2d2a0 ("bootcount: flush after storing the bootcounter")
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Even though the exception vector table is a fundamental part of the ARM
architecture, U-Boot mostly does not make real use of it, except when
crash dumping. But having it in takes up quite some space, partly due to
the architectural alignment requirement of 2KB. Since we don't take special
care of that, the compiler adds a more or less random amount of padding
space, which increases the image size quite a bit, especially for the SPL.
On a typical Allwinner build this is around 1.5KB of padding, plus 1KB
for the vector table (mostly padding space again), then some extra code
to do the actual handling. This amounts to almost 10% of the maximum image
size, which is quite a lot for a pure debugging feature.
Add a Kconfig symbol to allow the exception vector table to be left out
of the build for the SPL.
For now this is "default y" for everyone, but specific defconfigs,
platforms or .config files can opt out here at will, to mitigate the code
size pressure we see for some SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The arm64 exception handling code is quite big, mostly due to
architectural alignment requirements. Each exception entry spans 32
instructions, which sounds generous, but is too small to fit all of the
save/branch/restore code in there. So at the moment we use only four
instructions, branching into shared save and restore routines.
To not leave the space for those remaining 28 instructions wasted, let's
split the save and restore routines and stuff them into the gaps.
This saves about 250 bytes of code, which is helpful for those tight
SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Several boards do not use the default UART3, so they do a check
for ifdef CONFIG_SPL_BUILD and enable the pointer for
CONFIG_SYS_NS16550_COMx to point to OMAP34XX_UARTx.
Let's consoldate this all into one place, and remove them from the
individual boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch adds support for STMicroelectronics STM32 ADC (analog to
digital converter). It's originally based on Linux kernel v4.18-rcs
drivers/iio/adc/stm32-adc*. It's composed of:
- core driver (UCLASS_SIMPLE_BUS) manages common resources (clk, regu).
- child drivers (UCLASS_ADC) declare each ADC, channels and handle
conversions.
This driver currently supports STM32H7 and STM32MP1 ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds documentation of device tree bindings for the STM32 ADC.
It's based on linux-v4.18-rc* dt-bindings, at the time of writing:
- Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
device_get_supply_regulator() only needs to be called once.
But each time there's call to adc_vxx_value() for instance, it calls
adc_vxx_platdata_update() -> device_get_supply_regulator().
So, move device_get_supply_regulator() to pre_probe() routine.
This also allows vdd_supply/vss_supply to be provided directly from
uc_pdata, e.g dt-binding variant like stm32-adc provide its own
'vref-supply'.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add clk_valid() to check for optional clocks are valid.
Call clk_valid() in test/dm/clk.c and add relevant test routine to
sandbox clk tests.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Trivial Kconfig cleanup. Use tabs instead of spaces.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add spi driver for sun4i, sun5i and sun7i SoCs. The driver is
adapted from mailine kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This matches the compatible string used by the Linux kernel. This will
allow u-boot to use the same device tree files.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: use armada instead of orion on .data]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Get the is_errata_50mhz_ac in .ofdata_to_platdata, and
reuse it in .set_mode this can eventually initialized
dt code at once and adding room to add platdata.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for SPANSION s25fl128l
Signed-off-by: Clément Laigle <c.laigle@catie.fr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: fixed , at the end of } ]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Align the size of the carveout region to 2M. This ensures that the size
can be accurately represented by an LPAE page table that uses sections.
This solves a bug (hang at boot time soon after printing the DRAM size)
that only shows up when the following two commits are merged together:
d32e86bde8 ARM: HYP/non-sec: enable ARMV7_LPAE if HYP mode is supported
6e584e633d ARM: tegra: avoid using secure carveout RAM
Cc: Mark Kettenis <kettenis@openbsd.org>
Cc: Alexander Graf <agraf@suse.de>
Acked-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
At present this function takes a filename, but it is better to use an Fdt
object so that the caller can control this, perhaps obtainint the device
tree from a bytearray. Update the method accordingly and also fix a
confusing parameter name.
Signed-off-by: Simon Glass <sjg@chromium.org>
This property has been changed to 'offset'. To help downstream users who
might still be using 'pos', add a check that this is not used by mistake.
Signed-off-by: Simon Glass <sjg@chromium.org>
Laurentiu Tudor
Pankaj Bansal
Joakim Tjernlund
Vinitha V Pillai
Brendan Shanks
Jagdish Gediya
Tom Rini
Peng Fan
Neil Armstrong
Lukasz Majewski
Patrice Chotard
Alex Kiernan
Andre Przywara
Adam Ford
Fabrice Gasnier
Michal Simek
Koen Kooi
Stefan Mavrodiev
Chris Packham
Jagan Teki
Clément Laigle
Stephen Warren
Simon Glass