The original code would wrongly relocate the blob to be right before
the initrd if it existed. The blob *must* be within CFG_BOOTMAPSZ,
if it is defined. So we make two changes:
1) flag the blob for relocation whenever its address is above BOOTMAPSZ
2) If the blob is being relocated, relocate it before kbd, not initrd
Signed-off-by: Andy Fleming <afleming@freescale.com>
When CFG_POST_ETHER_EXT_LOOPBACK is defined, the ethernet POST
is not done using an internal loopback connection, but by assuming
that an external loopback connector is plugged into the board.
Signed-off-by: Stefan Roese <sr@denx.de>
Merge to two at45.c files into a common file, split to at45.c and spi.c
Fix spelling error in DM9161 PHY Support.
Initialize at91rm9200 board (and set LED).
Add PIO control for at91rm9200dk LEDs and Mux.
Change dataflash partition boundaries to be compatible with Linux 2.6.
Signed-off-by: Peter Pearse <peter.pearse@arm.com>
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
The PCI ID select values on the Arcadia main board differ depending
on the version of the hardware. The standard configuration supports
Rev 3.1. The legacy target supports Rev 2.x.
Signed-off-by Randy Vinson <rvinson@mvista.com>
Author: Randy Vinson <rvinson@linuxbox.(none)>
Enable the PCI-to-ISA bridge in the VIA Southbridge located on the
Arcadia main board.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This patch is against u-boot-mpc85xx.git of www.denx.com
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
This patch is against u-boot-mpc85xx.git of www.denx.com
Setting cpo to 0x9 for frequencies higher than 333MHz is verified on
both MPC8548CDS board and MPC8568MDS board, especially for supporting
533MHz DDR2.
Setting clk_adjust to 0x6(3/4 late cycle) for MPC8568MDS board is for
DDR2 on all current board versions especially ver 1.92 or later to bring
up.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
On e500 when we leave the 4k boot page we should use an absolute address since
we don't know where the board code may want us to be really running at.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current implementation does not set the number of bank address bits
(BA) in the processor. The default assumes 2 logical bank bits. This
works fine for a DIMM that uses devices with 4 internal banks (SPD
byte17 = 0x4) but needs to be set appropriately for a DIMM that uses
devices with 8 internal banks (SPD byte17 = 0x8).
Signed-off-by: Greg Davis <DavisG@embeddedplanet.com>
Some patches had inserted warnings into the build:
* mpc8560ads declared data without using it
* cpu_init declared ecm and immap without using it in all CONFIGs
* MPC8548CDS.h had its default filenames changed so that they contained
"\m" in the paths. Made the defaults not Windows-specific (or
anything-specific)
Signed-off-by: Andy Fleming <afleming@freescale.com>
Make the early L1 cache stack region guarded to prevent speculative
fetches outside the locked range.
Use _PHYS defines, not _MEM for cpu-side PCI memory mapped regions.
init.S whitespace cleanup.
Allow TEXT_BASE value to be specified on command line. This allows it
to be set to 0xfffc0000 which cuts the uboot binary in half.
Clear and enable lbc and ecm errors.
Update last_busno in device-tree for pci and pcie.
Remove load of obsolete cpu/mpc85xx/pci.0
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
PCI1 LAW mapping should use CFG_PCI1_MEM_PHY and not _BASE address.
Enable LBC and ECM errors and clear error registers.
Add tftpflash env var to get uboot from tftp server and flash it.
Add pci/pcie convenience env vars to display register space:
"run pcie3regs" to see all pcie3 ccsr registers
"run pcie3cfg" to see all cfg registers
Whitespace cleanup and MPC8544DS.h
Enable CONFIG_INTERRUPTS.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
From: Ed Swarthout <Ed.Swarthout@freescale.com>
Support external interrupts from platform to eliminate system hangs.
Define CONFIG_INTERRUPTS board configure option to enable.
Enable ecm, ddr, lbc, and pci/pcie error interrupts in PIC.
Remove extra cpu initialization redundant with hardware initialization.
Whitespace cleanup.
Define and use _START_OFFSET consistent with other processors using
ppc_asm.tmpl
Move additional code from .text to boot page to make room for
exception vectors at start of image.
Handle Machine Check, External and Critical exceptions.
Fix e500 machine check error determination in traps.c
TEXT_BASE can now be 0xfffc_0000 - which cuts binary image in half.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Only check for mpc8548 rev 1 when compiled for 8548.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Allow debugger to override flash cs0/cs1 settings to enable alternate
boot regions
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Always define MCK_EXCEPTION macro - so e500 can use it too.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Added CONFIG_BOOTP_SERVERIP to allow the tftp server to be different
from the bootp server
Signed-off-by: Wilson Callan <wcallan@savantav.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
PCI-Express sockets 1 and 2 verified working with Intel Pro/1000 PT
adapter.
Signed-off-by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Signde-off-by: Jon Loeliger <jdl@freescale.com>
Calculate the data timeout based on values from the CSD instead of
just using a hardcoded DTOR value. This is a backport of a similar fix
in BSP 2.0, with one additional fix: the DTOCYC value is rounded up
instead of down.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
include/asm-avr32/div64.h was recently moved to include/div64.h, but
cpu/at32ap/interrupts.c wasn't properly updated (an earlier version of
the patch was merged perhaps?)
This patch updates cpu/at32ap/interrupts.c so that the avr32 port
compiles again.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Instead of always using the largest blocksize the card supports, check
if it can support smaller block sizes and use 512 bytes if possible.
Most cards do support this, and other parts of u-boot seem to have
trouble with block sizes different from 512 bytes.
Also enable underrun/overrun protection.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
This patch was originall provided by David Mitchell <dmitchell@amcc.com>
and fixes a bug in the PLL clock calculation.
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk
Andy Fleming
Peter Pearse
Stefan Roese
Randy Vinson
Haiying Wang
Kumar Gala
Ed Swarthout
David Updegraff
Wilson Callan
Mike Rapoport
Ben Warren
Jon Loeliger
Joe Hamman
Haavard Skinnemoen