Remove code from the reset manager that is never called.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add wrapper around the designware MAC driver to handle the SoCFPGA
specific configuration bits. On Arria10, this is configuration of
syscon phy_intf.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The UART reset handling is now done via reset framework using the
SoCFPGA reset driver. The UART console assignment is done using the
DM and console framework. Nuke all this comlexity, since it is just
duplicating the same functionality, badly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Enable the DM I2C framework on Arria10, so that the DM capable
Designware I2C driver can handle the reset via DM reset framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Enable the DM reset framework and DM reset driver on Arria10 both
in U-Boot and in SPL. This lets U-Boot parse reset control from DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The A10 SoCDK is missing the I2C bus alias, so DM I2C cannot assign
the I2C bus a bus number. Add the missing alias.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The I2Cx resets are missing from DT, so the reset manager
cannot control them. Add the missing DT reset entries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add the GMAC0,1 OCP resets, which must also be ungated for those GMACs
to work and add GMAC2 reset and OCP resets which were missing altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The UART0 and UART1 resets are missing from DT, so the reset manager
cannot control them. Add the missing DT reset entries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The Altera reset manager block must be available very early on, since
it controls ie. UART resets. Flag it as pre-reloc.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The restructuring of the SPL dropped registration of the FPGA in SPL,
readd it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Fixes: c859f2a77d ("arm: socfpga: Restructure the SPL file")
Some of the code for low level system initialization in SPL's
board_init_f() and U-Boot's arch_early_init_r() is the same,
so let's combine it into a single function called from both.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Device trees need to have the serial console device available
before relocation and require a stdout-path in chosen at least
for SPL to have a console.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
If CONFIG_DEBUG_UART is enabled, correctly initialize
the debug uart before console is initialized to debug
early boot problems in SPL.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
In spl_gen5's board_init_f(), gd->malloc_base is manually assigned
at the end of the function to point to sdram. This code is outdated
as by now, the heap is switched to sdram by the common function
spl_relocate_stack_gd() if the appropriate defines are set.
As it was, the value assigned manually was directly overwritten by
this common code, so remove the manual assignment.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
There were NULL pointers dereferenced because DM was used
too early without correct initialization:
- malloc_simple returned NULL when called from preloader_console_init()
because gd->malloc_limit was 0
- uclass_add dereferenced gd->uclass_root members which were NULL because
dm_init (or one of its relatives) has not been called.
All this is fixed by calling spl_early_init before calling
preloader_console_init.
This fixes commit 73172753f4 ("ARM: socfpga: Convert to DM serial")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Travis CI now supports giving jobs an explicit name. Do this for all jobs.
This allows more direct control over jobs names than the previous
automatic or implicit naming based on the environment variables or script
text.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[trini: Update names for jobs added/changed since posting]
Signed-off-by: Tom Rini <trini@konsulko.com>
This update adds PPC64 ELF V1 ABI support to bootelf for both the
program header and section header options. Elf64 support was already
present for the program header option, but it was not handling the
PPC64 ELF V1 ABI case. For the PPC64 ELF V1 ABI, the e_entry field of
the elf header must be treated as function descriptor pointer instead
of a function address. The first doubleword of the function descriptor
is the function's entry address.
Signed-off-by: Rob Bracero <robbracero@gmail.com>
[trini: Fix whitespace issues]
Signed-off-by: Tom Rini <trini@konsulko.com>
Fixup the Linux FDT with the detection of onboard DRAM as
provided by SBL (Secondary boot loader) by reading
the shared-memory region.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Underlying API should already print some meaningful error message, so
this one is just brings more noise. E.g. we can see log like this:
MMC: no card present
** Bad device mmc 0 **
Obviously, second error message is unwanted. Let's only print it in case
when DEBUG is defined to keep log short and clear.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
"Failed" error message from env_load() only clutters the log with
unnecessary details, as we already have all needed warnings by that
time. Example:
Loading Environment from FAT... MMC: no card present
** Bad device mmc 0 **
Failed (-5)
Let's only print it in case when DEBUG is defined to keep log clear.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes the following checkstyle warning:
WARNING: Missing a blank line after declarations
+ int tmp = smbios_write_funcs[i]((ulong *)&addr, handle++);
+ max_struct_size = max(max_struct_size, tmp);
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixes the following chechpatch -f error:
ERROR: "(foo*)" should be "(foo *)"
+ strncpy((char*)t->uuid, serial_str, sizeof(t->uuid));
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Compressed images should have their compression property
set to "none" if U-Boot should leave them compressed.
This is especially the case for compressed ramdisks that
should be uncompressed by the kernel only.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
For these boards, the GPMC timings are more determined by
processor speed/type than the NAND/PoP memory. This code
is never invoked, so disable the config option, so it doesn't
take the time to compile it in.
Signed-off-by: Adam Ford <aford173@gmail.com>
Create separate html pages for linker lists, the serial subsystem,
and the EFI subsystem.
Add a table of content.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The console index for SPL should be 1 not 3 in order to see text during
SPL.
Fixes: 6f6b7cfa89 ("Convert all of CONFIG_CONS_INDEX to Kconfig")
Signed-off-by: Adam Ford <aford173@gmail.com>
sata_probe returns 1 for failure, so don't checkout for < 0
fixes: f19f1ecb60 dm: sata: Support driver model with the 'sata' command
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Initialize the led with the default state defined in device tree
in board_init and solve issue with test for led default state.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Initialize the led with the default state defined in device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch save common LED property "default-state" value
in post bind of LED uclass.
The configuration for this default state is only performed when
led_default_state() is called;
It can be called in your board_init()
or it could added in init_sequence_r[] in future.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This reverts commit bc882f5d5c.
because this patch adds the probe of LED driver during the
binding phasis. It is not allowed in driver model because
the drivers (clock, pincontrol) needed by the LED driver can
be also probed before the binding of all the device and
it is a source of problems.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch add the 4 LED available on the ED1 board and activated
gpio led driver.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add an initial MAINTAINERS file based on author of the code.
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
It might be useful for user to see some human-readable root cause
message in addition to "configuration failed" message, so that the issue
can be fixed quickly.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
In case of error in dfu_init_env_entities(), env_bkp will leak. Fix it
by providing single return path.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Commit 5d8fae7916 ("dfu: avoid memory leak") brings a regression which
described below. This patch is effectively reverting that commit, adding
corresponding comment to avoid such regressions in future.
In case of error in dfu_config_entities(), it frees "dfu" array, which
leads to "data abort" in dfu_free_entities(), which tries to free the
same array (and even tries to access it from linked list first). The
issue occurs e.g. when partition table on device does not match
$dfu_alt_info layout:
=> dfu 0 mmc 1
Couldn't find part #2 on mmc device #1
DFU entities configuration failed!
data abort
To fix this issue, do not free "dfu" array in dfu_config_entities(). It
will be freed later in dfu_free_entities().
Tested on BeagleBone Black (where this regression was originally found).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
As well as in K_FW_LBA_READ_10 and K_FW_LBA_ERASE_10 take device's
block size from f_rkusb->desc->blksz instead of the fixed 512 bytes.
Keep original behaviour of retry probing assigned block device on
every host request to manage late SDCard plugs.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
While downloading or uploading megabytes of data we had thousands of
printf in console like:
transfer 0x10000 bytes done
OR
Uploading 0x1000 bytes
This because transfers are chunked and there is no way on target
side to know the overall transfer size (to print one string per
overall transfer).
All these prints on serial console do slow down significantly the
transfer and does not offer a significant information to the
developer: rkdeveloptool and Rockchip original tool do use small
chunks read/writes on big transfers. This allows on workstation
to print percentage of transfer complete and as well offers to
developer the information about: transfer is running OK.
On error, either the percentage will stop or an error will be shown
on workstation console.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
This command is part of the write partition sequence performed by
rkdeveloptool: one partition is first completely erased and
than wrote.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch implement reading blocks form selected device with
LBA addressing.
Corresponding command on workstation is:
rkdeveloptool rl <start_blk> <blk_cnt> <file>
While we support reading more than one blocks per K_FW_LBA_READ_10
request, rkdeveloptool and original rockchip tool do perform
chunk reads limiting the maximum size per chunk far lower
than max int values.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut
Simon Goldschmidt
Simon Goldschmidt
Stephen Warren
Rob Bracero
Ramon Fried
Sam Protsenko
Christian Gmeiner
Adam Ford
Heinrich Schuchardt
Troy Kisky
Patrick Delaunay
Tom Rini
Alberto Panizzo