Add cfi-mtd driver, which exports CFI flash to MTD layer.
This allows CFI flash devices to be used from MTD layer.
Building of the new driver is controlled by CONFIG_FLASH_CFI_MTD
option. Initialization is done by calling cfi_mtd_init() from
flash_init().
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add interface for flash verbosity control. It allows
to disable output from low-level flash API. It is useful
when calling these low-level functions from context other
than flash commands (for example the MTD/CFI interface
implmentation).
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Export flash_sector_size() function from drivers/mtd/cfi_flash.c,
so that it can be used in the upcoming cfi-mtd driver.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch defines all flash access functions as weak so that
they can be overridden by board specific versions.
This will be used by the upcoming VCTH board support where the NOR
FLASH unfortunately can't be accessed memory-mapped. Special
accessor functions are needed here.
To enable this weak functions you need to define
CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS in your board config header.
Otherwise the "old" default functions will be used resulting
in smaller code.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
address-cells defaults to 2, not 1; so in the unlikely
event that it isn't specified, this patch is required
for correct operation.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Doing trap_init immediately once we're running from RAM
means we're no longer dependent on the physical location of
the flash on non-BookE platforms. Before trap_init, those
platforms switch to real mode and go to 0xfff00100 on exception.
After the switch, they go to 0x00000100 This makes it easier to
move the flash location.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Since we've changed the memory map of the board, be nice and
add some checking to try to catch out-of-date .dts files. We do
this by checking the CCSRBAR location in the .dts and comparing
it to the CCSRBAR location in u-boot. If they don't match, a
warning msg is printed. This isn't foolproof, but it's simple and
will catch most of the cases where an out-of-date .dts is present,
including all of the cases where a new u-boot is used with an old
standard MPC8641 .dts file as supplied with Linux.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
This patch creates a memory map with all the devices
in 36-bit physical space, in addition to the 32-bit map.
The CCSR relocation is moved (again, sorry) to
allow for the physical address to be 36 bits - this
requires translation to be enabled. With 36-bit physical
addressing enabled, we are no longer running with VA=PA
translations. This means we have to distinguish between
the two in the config file. The existing region name is
used to indicate the virtual address, and a _PHYS variety
is created to represent the physical address.
Large physical addressing is not enabled by default.
Set CONFIG_PHYS_64BIT in the config file to turn this on.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.
The regions for some of the mappings were far larger than they
needed to be. I have reduced the mappings to match the
actual sizes supported by the hardware.
In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them. These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.
Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
We define CONFIG_MONITOR_BASE_EARLY to define the initial location
of the bootpage in flash. Use this to create an early mapping
definition for the FLASH, and change the early_bats code to use this.
This change facilitates the relocation of the flash since the early
mappings are no longer tied to the final location of the flash.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Using a mtmsr/blr means that you have to be executing at the
same virtual address once you enable translation. This is
unnecessarily restrictive, and is not really how this is
usually done. Change it to use the more common mtspr SRR0/SRR1
and rfi method.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
There's a lot of setup and foo for the second flash
bank. The problem is, this board doesn't actually have one.
Clean this up. Also, the flash is 8M in size. Get rid
of the confusing aliased overmapping, and just map 8M.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
It's currently defined twice inside in an if/else block, but
both halves set the same value. Move the define outside
the if.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
In order to later allow for a physical relocation of the
flash, setup_bats, which sets up the final BAT mapping
for the board, needs to happen *after* init_laws().
Otherwise, there will be no window programmed for the flash
at the new physical location at the point when we change
the mmu translation.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Copied over the fixed PHY driver as used in pp4xx/4xx_enet.c.
This adds support for PHY-less MAC connections to the UEC.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
All CF platforms' mii.c are consolidated into one
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Also changed path in all linker scripts that reference this driver
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
All in-tree IBM/AMCC PPC4xx boards using the EMAC get this new CONFIG
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Affected boards:
Several MPC8xx boards
Several MPC8260/MPC8272 boards
Several MPC85xx boards
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch will move au1x00_eth_initialize from net/eth.c to cpu_eth_init
as a part of ongoing eth_initialize cleanup work. The function ret value
is also fixed as it should be negative on fail.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Patch to fix buffer allocation size and alignment. Buffer needs to be u32 aligned and
PKTSIZE_ALIGN bytes long.
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The current uec_miiphy_read and uec_miiphy_write hardcode access devlist[0]
This patch makes these function use the devname argument that is passed in to
allow access to the phy registers of other devices in devlist[].
Signed-of-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Fixed compiler warning "declared but unused" eth5_uec_info and eth6_uec_info.
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
AT91_BASE_EMAC is never used outside the board specific files,
so replace its usage by the board specific AT91xxx_BASE_EMAC.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
AT91_ID_US0 / AT91_ID_US1 / AT91_ID_US2 were used but never defined.
Since they are never used outside the board specific files, they can
be replaced by the board specific AT91xxx_ID_US0 / AT91xxx_ID_US1 /
AT91xxx_ID_US2.
Bug spotted by Jesus Alvarez <jalvarez@micromint.com>.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch provides support for AFEB9260 board, a product of
OpenSource hardware and software. Some commertial projects
are made with this design. A board is basically AT91SAM9260-EK
with some modifications and different peripherals and different
parts used. Main purpose of this project is to gain experience in
hardware design.
More info: http://groups.google.com/group/arm9fpga-evolution-board
(In Russian only, sorry).
Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
OMAP identification is implemented in 'cpuinfo.c' and located in ARM926EJ-S directory.
It makes sense to place this file in OMAP specific subdirectory, i.e. cpu/arm926ejs/omap
Signed-off-by: Roman Mashak <romez777@gmail.com>
We put the bootpg for the secondary cpus into memory and use
BPTR to get to it. This is a step towards converting to the
ePAPR boot methodology. Also, the code is written to
deal properly with more than 4GB of RAM.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
There are several items in the config file that were hardcoded
but that should really be based on other config options, since
the regions are contiguous and depend on being so. This cleans
that up a bit. Also, add BR_PHYS_ADDR() macro to convert
addresses into the proper format for BR registers.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Piotr Ziecik
Stefan Roese
Selvamuthukumar
Wolfgang Denk
Becky Bruce
Jon Loeliger
Richard Retanubun
TsiChung Liew
Ben Warren
Shinya Kuribayashi
Clive Stubbings
Stelian Pop
Jean-Christophe PLAGNIOL-VILLARD
Sergey Lapin
Tomohiro Masubuchi
Roman Mashak