Convert GPIO names from Kconfig strings into pin numbers for
the 'ssd2828_config' struct. Add SSD2828 initialization between
enabling the parallel LCD interface and turning on the backlight.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SSD2828 can take pixel data coming from a parallel LCD interface
and translate it on the fly into MIPI DSI interface for driving
a MIPI compatible TFT display. SSD2828 is configured over SPI
interface, which may or may not have MISO pin wired up on some
hardware. So a write-only SPI mode also has to be supported.
The SSD2828 support code is implemented as a utility function
and needs to be called from real display drivers, which are
responsible for driving parallel LCD hardware in front of the
video pipeline. The usage instructions are provided as comments
in the header file.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The file, originally named "include/video/mipi_display.h", is taken from
linux 3.18 (commit b2776bf7149bddd1f4161f14f79520f17fc1d71d).
It provides MIPI DSI constants for DCS commands, which are needed to
implement support for SSD2828 in u-boot.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
And also add Kconfig option for selecting ELDO3 voltage. The reason
for having this option is that the Android kernel sets ELDO3 to
1.2V when powering up LCD in the case if 'lcd_if' configuration
variable is set to 6 (LCD_IF_EXT_DSI) in the FEX file. Most likely
to supply power for a SSD2828 chip.
However on the MSI Primo81 tablet, which is using this particular
'lcd_if = 6' setup for LCD, setting the ELDO3 voltage appears to
be unnecessary and it works regardless. Having no schematics of
this tablet, I can only guess that 1.2V is supplied to SSD2828
in some other way.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has
an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand,
a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG)
and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic,
the axp152.
For more details see: http://linux-sunxi.org/Semitime_g2
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it
features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro
usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic.
For more details see: http://linux-sunxi.org/Rikomagic_mk802ii
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The mk802 is the "classic" Allwinner A10 based hdmi tv-stick, it features
512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle,
mini-usb receptacle (OTG) and USB-wifi. Somewhat unique the mk802 does not
use the AXP209 pmic, it does not have a pmic at all.
For more details see: http://linux-sunxi.org/Rikomagic_mk802
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
CONFIG_TARGET_FOO is only used in board/sunxi/Makefile to select the
dram config for sun5i and sun7i boards and in board/sunxi/gmac.c for some
special handling of the bananapi/bananapro (both sun7i), iow it is not used
at all on any sun4i, sun6i and sun8i boards so lets get rid of it there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Currently we've separate detailed dram settings for all sun4i boards, this
moves them over to using auto dram configuration so that we can get rid of
all the per board dram_foo.c files.
Tested-by: Hans de Goede <hdegoede@redhat.com> on a A10-OLinuXino-Lime,
Chuwi_V7_CW0825 and ba10_tv_box
Tested-by: Zoltan HERPAI <wigyori@uid0.hu> on a pcduino
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While working on adding more boards I noticed that we lack a config for
the 512M cubieboard, and that some of the new boards which I want to add also
have 512M and 1G variants, rather then adding 2 defconfig's for all of these,
lets switch the exising boards which have both a 512M and 1024M variant over
to the sun4i dram autoconfig code.
This also drops the foo_RAMSIZE_defconfig variants of boards where we currently
have 2 separate configs already.
Note:
1) The newly introduced CONFIG_DRAM_EMR1 kconfig value is not used with
a value other then its default for now, but we need this to be configurable
to support some new boards with auto dram config.
2) We always set all CONFIG_DRAM_foo values in defconfigs, even if they match
the defaults, this is done to make it more clear what values are used for a
certain board.
This has been tested on a Mele A1000, Mini-X and a Cubieboard, all 1G
variants, the dram autoconfig code has also been tested on a 512M mk802
(a defconfig for the mk802 is added in a later patch).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We do not use the axp209 interrupt, and at least in my mini-x (which does not
have a power button) the pwr-button pin and the irq pin are soldered together,
so if the axp209 keeps it irq asserted too long it will see a 10s pwr-button
press and hard power off the board, disabling the irqs fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The clocks on the A80 are hooked up slightly different, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Wait 1 second for the sdcard to respond, rather then waiting for
0xfffff milliseconds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add initial sun9i (A80) clock setup support, enough to get the uart + mmc
going.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a headerfile with all the base addresses from the sun9i blocks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sun4i - sun8i have (aprox.) the same iomem layout, but sun9i is quite
different, so add a wrapper cpu.h which includes the right mach specific
cpu_sun#i.h based on mach, like we already do with clock.h and dram.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Which pll-s are available depends on the machine type, move the
clock_get_pllX / clock_set_pllX prototypes to the clock_sun?i.h header files
so that we only declare what is actually available. e.g. clock_get_pll5p()
is not available on sun6i / sun8i, and with sun9i we get a completely
different set of plls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
As the comment says now that we have SPL support this is no longer necessary,
as PLL6 is already setup with the exact same parameters by the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.
This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.
This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.
The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2 recent sunxi changes have removed the usage of lowlevel_init by moving some
code around and then setting CONFIG_SKIP_LOWLEVEL_INIT.
This is problematic for 2 reasons:
1) It does not just stop s_init from being called, it also stops
cpu_init_cp15 from getting called, which is undesirable.
2) We want u-boot.bin to be usable standalone, without SPL, some people e.g.
use an upstream u-boot.bin together with Allwinner's boot0 loader. So
u-boot.bin must (re)initialize the gpios, timer, etc.
This commit restores the lowlevel_init / s_init usage, while keeping the
changes to no longer use the global-data (gd) struct in the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Wider bus widths (larger than default 1 bit) appeared in MMC standard
version 4.0. So, for MMC cards of any earlier version trying to change
the bus width (including ext_csd comparison) does not make any sense.
It may work incorrectly and at least cause unnecessary timeouts.
So, just skip the entire bus width related activity for earlier versions.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
If all the commands switching an MMC card to 4- or 8-bit bus width fail,
and the bus width for the controller and the driver is still set
to default 1 bit, there is no need to send one more command to switch
the card to 1-bit bus width. Also, if the card or host controller do not
support wider bus widths, there is no need to send a switch command at all.
However, if one of switch commands succeeds, but the subsequent ext_csd
fields comparison fails, the card should be switched to some other bus width
(next in the list for the loop), or to default 1-bit bus width as a last
resort. That's why it would be incorrect to just remove the 1-bit bus width
case from the list, it should still be processed in some cases.
panto: Minor cosmetic edit removing superfluous parentheses.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
This extends the mmcinfo hardware partition info output to show
partitions with write reliability enabled with the "WRREL" string.
If the partition does not have write reliability enabled the "WRREL"
string is omitted; this is analogous to the ehhanced attribute.
Example output:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
Erase Group Size: 8 MiB
HC WP Group Size: 16 MiB
User Capacity: 13.8 GiB ENH WRREL
User Enhanced Start: 0 Bytes
User Enhanced Size: 512 MiB
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH WRREL
GP2 Capacity: 64 MiB ENH WRREL
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
This change extends the mmc hwpartition sub-command to change the
per-partition write reliability settings. It also changes the
syntax used for the enhanced user data area slightly to better
accomodate the write reliability option.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The eMMC partition write reliability settings are to be set while
partitioning a device, as per the eMMC spec, so changes to these
attributes needs to be done in the hardware partitioning API.
This commit adds such support.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Adds the mmc hwpartition sub-command to perform eMMC hardware
partitioning on an mmc device. The number of arguments can be
large for a complex partitioning, but as the partitioning has
to be done in one go it is difficult to make it simpler.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
This adds an API to do hardware partitioning on eMMC devices. The
new mmc_hwpart_config() function does the partitioning in one go.
As the different attributes and partitioning options on eMMC may
be interdependent validation has to be done based on the complete
partitioning configuration. The function accepts three modes:
- MMC_HWPART_CONF_CHECK: just validates that the configuration
is valid.
- MMC_HWPART_CONF_SET: validates and sets all the fields in
EXT_CSD but without setting the "partitioning completed" bit,
and thus is reversible.
- MMC_HWPART_CONF_COMPLETE: does everything and is thus not
reversible.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The mmc_startup() function uses the ext_csd data even if reading it
from the mmc device failed. This bug was introduced in commit
bc897b1d4d. We now bail out if
reading it fails, this should not be a problem as ext_csd was
introduced in MMC 4.0 and this code is conditional on MMC >= 4.0.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The eMMC spec says that partitioning is only effective after the
PARTITION_SETTING_COMPLETED is set in EXT_CSD (and a power cycle was done,
but that we cannot know). Thus the partition sizes and attributes should
be ignored when that bit is not set, otherwise the various capacities
are not coherent (e.g., the user data capacity will be that of the
unpartitioned device while partition sizes would be non-zero).
Prescence of non-zero partitioning data is nevertheless still used to
activate the high-capacity size definitions (EXT_CSD_ERASE_GROUP_DEF)
as it is necessary to set that to write any of the partitioning fields
in EXT_CSD, so having partitioning data means someone previously
activated that and we should keep it activated.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
This adds the erase group size and high-capacity WP group size to
mmcinfo's output. The erase group size is necessary to properly align
erase requests on eMMC. The high-capacity WP group size is necessary
to properly align partitions on eMMC.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Read the eMMC high capacity write protect group size at mmc device
initialization. This is useful to correctly partition an eMMC device,
as partitions need to be aligned to this size.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The erase_grp_size in struct mmc is to be a size in 512-byte sectors
but the code used to compute it for eMMC when EXT_CSD_ERASE_GROUP_DEF is
enabled computed it as bytes, leading to erase sizes and alignment
much larger than what is actually required by the mmc device.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
This adds output to show the eMMC enhanced user data area size and offset
along with the partition sizes in mmcinfo's output.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
This modification reads the size of the eMMC enhanced user data area
upon initialization of an mmc device, it will be used later by
mmcinfo.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The eMMC spec mandates that the high-capacity group size definitions
should be enabled when the device is partitioned (by setting
ERASE_GROUP_DEF in EXT_CSD). The current test to determine when this is
required misses a few cases. In particular a device may have been
partitioned without setting the enhanced attribute on any partition
or partitioning may be completed without creating any extra partitions.
This change moves the code to set ERASE_GROUP_DEF to after reading
all partition information. It is also enabled when
PARTITIONING_SETTING_COMPLETED is set as it is necessary to enable
ERASE_GROUP_DEF before setting that bit, so it means that the user
previously switched to the high capacity definitions.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
eMMC partitions are defined as of eMMC 4.41, but mmcinfo process
partition info for eMMC >= 4.0, change it to do it for >= 4.41
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The eMMC spec numbers general purpose partitions starting at 1, but
the mmcinfo output follows the internal numbering which starts at 0.
Make the mmcinfo command output number partitions as in the eMMC
spec to avoid confusion.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
This extends the mmcinfo command's output to show which eMMC partitions
have the enhanced attribute set. Note that the eMMC spec says that
if the enhanced attribute is supported then the boot and RPMB
partitions are of the enhanced type.
The output of mmcinfo becomes:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
User Capacity: 13.8 GiB ENH
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH
GP2 Capacity: 64 MiB ENH
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Siarhei Siamashka
Hans de Goede
Tom Rini
Sinan Akman
Simon Glass
Andrew Gabbasov
Diego Santa Cruz