This patch adds an GPIO LED boot status for IGEP boards.
The GPIO LED used is the red LED0 while the Linux kernel
uses the green LED0 as the boot status.
By using different GPIO LEDs, the user can know in which
step of the boot process the board currently is.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Even when the IGEPv2 board and the IGEP Computer-on-Module
are different from a form factor point of view, they are
very similar in the fact that share many components and how
they are wired.
So, it is possible (and better) to have a single board file
for both devices and just use the CONFIG_MACH_TYPE to make
a differentiation between each board when needed.
This change avoids code duplication by removing 298 lines of
code and makes future maintenance easier.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings. This saves about
90 bytes of space in SPL.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
The total RAM size of the IGEP-based boards is 512MiB not 1GiB, the
LPDDR memory consist on two dies of 256MiB.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
This patch adds SPL support for IGEP-based boards.
Tested on an IGEPv2 Rev.C board with Micron NAND Flash memory.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
This is rework on config files of IGEP-based boards with the aim to remove
duplicated code to be more maintainable. Basically this patch creates a
common configuration file for both boards and only sets the specific option
in the board config file.
On board files the hardcored mach type was replaced in favour of using the
CONFIG_MACH_TYPE option.
More than 200 duplicated lines have been deleted.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
The existing timing does not quite meet the minimum requirements
in the LAN9221 datasheet. The timing in this patch solves problems
noticed on some parts. The patch also combines the CS configuration
for the overo and igep0020 boards per request.
Signed-off-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
This patch switches from the legacy mmc driver to the new generic mmc driver
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added function to differentiate between the OMAP3EVM revisions. The
chip-id of the ethernet PHY is being used for this purpose.
Rev A to D : 0x01150000
Rev >= E : 0x92200000
CC: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Sandeep Paulraj <s-paulraj@ti.com>
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_SMC911X* to CONFIG_SMC911X*
- cleaned up line lengths
- modified all boards that override weak function in this driver
- added
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
Add BeagleBoard support, common power code and README.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Nikita Kiryanov
Javier Martinez Canillas
Peter Barada
Enric Balletbò i Serra
Jonathan Solnit
Philip Balister
Sanjeev Premi
John Rigby
Enric Balletbo i Serra
Ajay Kumar Gupta
Jean-Christophe PLAGNIOL-VILLARD
Dirk Behme
Matthias Ludwig
Ben Warren
Tom Rix