The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for NAND_MAX_CHIPS to the MTD NAND layer.
Multi-chips devices are displayed as shown:
Device 0: 2x NAND 512MiB 3,3V 8-bit, sector size 128 KiB
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When initializing the core clocks, stick external memory into self-refresh.
This gains us a few cool things:
- support suspend-to-RAM with Linux
- reprogram clocks automatically when doing "go" on u-boot.bin in RAM
- make sure settings are stable before flashing new version
- finally fully unify initialize startup code path between LDR/non-LDR
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some newer Blackfins (like the BF51x) do not have an on-chip voltage
regulator, so do not attempt to program the memory as if it does.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If the board config does not specify an explicit EBIU_SDBCTL value, set it
up with sane values based on other configuration options.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Workaround anomaly 432:
The bfrom_SysControl() firmware function does not clear the SIC_IWR1
register before executing the PLL programming sequence. Therefore, any
interrupt enabled in the SIC_IWR1 register prior to the call to
bfrom_SysControl() can prematurely terminate the idle sequence required
for the PLL to relock properly. SIC_IWR0 is properly handled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Boot ROM uses EVT1 as the entry point so set that rather than having
to use a tiny jump block in the default EVT1 location.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SPORT_TX registers cannot be read (the hardware will trigger an error),
so drop the read helper macros.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If there is some problem in the flash init/checking code, it's nicer to see
the message "Flash:" before crashing. This way the source of the problem
is a bit more straightforward.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the PORTJ on the BF537 is peripheral-only (no GPIO functionality),
then there is no PORTJ_FER register for us to worry about.
Signed-off-by: Sonic Zhang <Sonic.Zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The jtag tstc operation was checking the hardware to see if data is
available from it (which is fine for the jtag getc operation), but the
higher layers need to know whether any data is available. Since we have
to read up to 4 bytes at a time from the hardware, the higher layers need
to know they can consume the cached bytes as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Unify all of the net-related init code in the common Blackfin board init
code to clean up the ifdef mess a bit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On the pcm030 the environment is located in the onboard EEPROM. But we want
to handle flash sector protection in a safe manner. So we must read the
unlock environment variable from EEPROM instead from flash.
This patch is required as long the evironment is saved into the EEPROM.
Stefan: Additional change as suggested by Wolfgang, use bigger char array
(instead of 4).
Signed-off-by: Eric Schumann <E.Schumann@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
On systems where U-Boot is linked to another address than it really lays
(e.g. backup image), calls via function pointers must be fixed with a
'+= gd->reloc_off'.
This was not done for none_compr in ubifs_compressors_init() what leads
to system crash on ubifsmount command.
Signed-off-by: Michael Lawnick <ml.lawnick@gmx.de>
Acked-by: Stefan Roese <sr@denx.de>
This patchset adds these UBIFS related commands:
- ubifsmount
Mount an UBIFS volume
- ubifsls
List a directory of the mounted UBIFS volume
- ubifsload
Load a file from the mounted UBIFS volume to memory
Signed-off-by: Stefan Roese <sr@denx.de>
The U-Boot UBIFS implementation is largely a direct copy from the current
Linux version (2.6.29-rc6). As already done in the UBI version we have an
"abstraction layer" to redefine or remove some OS calls (e.g. mutex_lock()
...). This makes it possible to use the original Linux code with very
little changes. And by this we can better update to later Linux versions.
I removed some of the Linux features that are not used in the U-Boot
version (e.g. garbage-collection, write support).
Signed-off-by: Stefan Roese <sr@denx.de>
CC: Artem Bityutskiy <dedekind@infradead.org>
CC: Adrian Hunter <ext-Adrian.Hunter@nokia.com>
This patch adds LZO decompression support to U-Boot. It is needed for
the upcoming UBIFS support, since UBIFS uses LZO as default compressor/
decompressor. Since we only support read-only in UBIFS, only the
decompressor is needed.
All this is copied with minor changes from the current Linux kernel
version (2.6.28-rc8).
This patch only implements this LZO decompressor support for PPC.
Other platforms using UBIFS will have to add the required
"include/asm/unaligned.h" as well. It should be fairly easy to copy this
from the Linux source tree as I have done it for PPC in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Wolfgang Grandegger
Mike Frysinger
Sonic Zhang
Wolfgang Denk
Haavard Skinnemoen
Jean-Christophe PLAGNIOL-VILLARD
Eric Schumann
Jon Smirl
Nicolas Ferre
Vivek Kutal
Michael Lawnick
Stefan Roese