Enable building of drivers/net/phy/realtek.c so that realtek phys
get properly initialized.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
This symbol is not used anywhere, so remove it. For spear600, remove
it from the board file, since the symbol is not defined for spear600
either.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.
This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some sunxi-based boards (such as the Olimex A20-SOM-EVB) have a
second MMC socket. This socket is not bootable hardware-wise,
i.e. u-boot itself cannot be loaded from it, but once u-boot has
started, the second socket can be used in the boot process
provided by config_distro_bootcmd.h.
If a second MMC socket is present, place it in the boot order
after the first MMC socket.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enabled support for AXP818 in SPL and u-boot.
DCDC1, DCDC2, DCDC3 and DCSC5 are enabled.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The DFU protocol implementation in U-Boot is much faster than the
FEL protocol implementation in the boot ROM on Allwinner devices.
Using DFU instead of FEL improves the USB transfer speed from
500-900 KB/s to 3.2-3.7 MB/s. This is particularly useful for
reducing the time needed for booting systems with large initrd
images.
FEL is still useful for loading the U-Boot bootloader and a boot
script, which may then activate DFU in the following way:
setenv dfu_alt_info ${dfu_alt_info_ram}
dfu 0 ram 0
bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}
The rest of the files can be transferred to the device using the
"dfu-util" tool.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Zap CONFIG_NS16550_SERIAL, as the unification of ns16550 drivers
is completed.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_dw, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.
Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Not all sunxi boards have an MMC embedded. Switching to the Kconfig option
will allow to enable or disable the support in each boards' defconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When using the fastboot boot command, the image sent to U-Boot will be an
Android boot image. If the support is missing, that obviously won't work,
so we need it in our configuration.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a bootcmd_sunxi_compat value to the default environment when building
with CONFIG_OLD_SUNXI_KERNEL_COMPAT, this way people who occasionally want
to boot an old kernel can do so by simply typing "run bootcmd_sunxi_compat"
rather then needing to have 2 separate setups / sdcards for old and
new kernels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
common/dlmalloc.c is quite big, both in .text and .data usage. E.g. for a
Mele_M9 sun6i board build this reduces .text from 0x4214 to 0x3b94 bytes,
and .data from 0x54c to 0x144 bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@konsulko.com>
Select CONFIG_SPL_STACK_R for sunxi boards, this gives us much more
room on the stack once we've the DRAM running.
Besides being a good change to have on itself, this also paves the
way for switching to using malloc_simple in the SPL which cuts of
close to 4KiB of the SPL size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch makes use of the previous changes to add a new "fel" boot
target for sunxi boards.
When booting via FEL, it's often desirable to work around the absence
of other (usable) boot devices - or to be able to override them,
deviating from the standard boot sequence. To achieve this, the "fel"
boot target gets the highest priority, but won't actually do anything
unless certain criteria are met.
The "bootcmd_fel" implementation proposed here first tests if an actual
FEL boot takes place (using the "fel_booted" env var), and secondly
checks that "fel_scriptaddr" was set (originating from the 'loader',
i.e. the sunxi-tools fel utility). If both checks pass, then it will
try to execute the boot script (boot.scr) at the given address. In case
of an error (e.g. an invalid image), the source command might return
"false", causing "distro_bootcmd" to proceed with the next boot target.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For the upcoming nand support we need a bigger heap, esp. ubi[fs] uses
quite a bit of memory, increase the heap size to 64 MB.
Our video code returns unused reserved framebuffer memory to the kernel
before booting it. Drop the #ifdef-ery and simply always reserve 16 MB.
Adjust bootm_size for the above changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move some #define-s around from one #ifdef block to another to
reduce the number of #ifdef blocks (note this causes no functional
changes even though the conditions are not always exactly the same)
and move generic #include statements to the top.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig, just like
SYS_NAND_BUSWIDTH_16BIT this is only enabled on some SoCs using depends,
to avoid double defining it for SoCs which have not yet moved to Kconfig
for this.
Having this in Kconfig is useful because this is something which may
differ from one board to the other even when using the same SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Scott Wood <scottwood@freescale.com>
We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.
Renaming the Kconfig option now makes things easier when we add full
nand support in the future.
The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
CONFIG_SPL_NAND_SUPPORT gets used via IS_ENABLED so it must be defined
to 1, rather then just being defined.
While at remove 2 other unused NAND related defines from sunxi-common.h.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge,
such as found on the Colombus devkit.
While at it also fix the wrong indentation of the SSD2828 Kconfig help text
in board/sunxi/Kconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for making the visual area of the framebuffer smaller and
drawing a black border around it. This is intended for use with
overscanning monitors (esp. with composite video out), to avoid part
of the picture being invisible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add option to set shell prompt string from menuconfig and migrate
boards globally.
The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
Do not add a bogus (pointing to a non existing serial port) stdout-path
alias to dts on boards without a serial port.
Note that we still define CONS_INDEX as this is used by the SPL where we do
not use DM_SERIAL and thus CONFIG_REQUIRE_SERIAL_CONSOLE is not honored.
We are getting away with this because the sun5i die actually has
an uart0, which in the A13 package is not routed to the outside,
so we are simply sending SPL bootup messages to the tx pin at the
edge of the die, and they go no further from there...
And sofar we only have one A13 board which does not have a serial
port, all others do have a serial port. This kinda makes sense since
the A13 is a much lower pincount package compared to all the other
sunxi SoCs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.
This commit also introduces the configurable options in Kconfig.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds some config options to the sunxi-common config to enable the USB
download gadget and the fastboot and USB mass storage functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Now that some things were updated in Kconfig, they should be reflected on the
sunxi-common config too.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Start using the new Kconfig options which are available for these now,
and simply always enable them by selecting them as sunxi builds always
include USB support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
Due to absence of CONFIG_SYS_64BIT_LBA, u-boot-sunxi currently has
no support for the (GPT) partioning scheme of large disks > 2TB.
While the AHCI driver seems to handle this nicely, the problem is
that lbaint_t values get truncated to 32-bit.
This patch sets CONFIG_SYS_64BIT_LBA from sunxi_common.h for all
SoCs that support AHCI (CONFIG_SUNXI_AHCI).
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Another shell scripting command that has not been moved.
Moved using tools/moveconfig.py using these settings:
CMD_SETEXPR bool n y
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A1 SRAM Base differs between sun9i and the others, update sunxi-common.h
to deal with this, so that we do not set the initial stack pointer to point
to the BROM.
This avoids the need for the weird undocumented register write I previously
took from the allwiner u-boot sources and which needed #ifdef-ery in start.S
as it needed to be done really early on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The DRAM Base differs between sun9i and the others, update sunxi-common.h to
deal with this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The latest versions of the fel tool support loading normal u-boot builds
directly, and this is now the preferred way to use the fel boot method.
This commit removes support for the old deprecated standalone fel builds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Sunxi platforms use ARM Cortex A8, A7 and A15 (unsupported yet) CPU cores,
which all have 64 bytes cache line size.
This is required to e.g. enable USB gadget.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for UART2 (2-pin version but note that RTS/CTS pins are available
pn that port for possible future use), can be selected in config
by using CONFIG_CONS_INDEX=3
Signed-off-by: Laurent Itti <laurentitti@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On my A10 OlinuxIno Lime I noticed a huge (5+ seconds) delay coming from
console_init_r. This turns out to be caused by the preconsole buffer flushing
to the cfb_console. The Lime only has a 16 bit memory bus and that is already
heavy used to scan out the 1920x1080 framebuffer.
The problem is that print_pre_console_buffer() was printing the buffer once
character at a time and the cfb_console code then ends up doing a cache-flush
for touched display lines for each character.
This commit fixes this by first building a 0 terminated buffer and then
printing it in one puts() call, avoiding unnecessary cache flushes.
This changes the time for the flush from 5+ seconds to not noticable.
The downside of this approach is that the pre-console buffer needs to fit
on the stack, this is not that much to ask since we are talking about plain
text here. This commit also adjusts the sunxi CONFIG_PRE_CON_BUF_SZ to
actually fit on the stack. Sunxi currently is the only user of the pre-console
code so no other boards need to be adjusted.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that the ohci code supports usb interrupt queues we can switch (back)
to using an usb interrupt queue for usb-kbd interrupt polling. This
greatly reduces u-boot's latency when dealing with usb keyboards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit adds support for the OHCI companion controller, which makes
usb-1 devices directly plugged into to usb root port work.
Note for now this switches usb-keyboard support for sunxi back from int-queue
support to the old interrupt polling method. Adding int-queue support to the
ohci code and switching back to int-queue support is in the works.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede
Simon Glass
Jelle van der Waa
Marek Vasut
Thomas Chou
Karsten Merker
vishnupatekar
Siarhei Siamashka
Masahiro Yamada
Maxime Ripard
Bernhard Nortmann
Boris Brezillon
Nikita Kiryanov
Piotr Zierhoffer
Paul Kocialkowski
Ian Campbell
Joe Hershberger
Daniel Kochmański
Laurent Itti