While actually switching to non-secure state is one thing, another
part of this process is to make sure that we still have full access
to the interrupt controller (GIC).
The GIC is fully aware of secure vs. non-secure state, some
registers are banked, others may be configured to be accessible from
secure state only.
To be as generic as possible, we get the GIC memory mapped address
based on the PERIPHBASE value in the CBAR register. Since this
register is not architecturally defined, we check the MIDR before to
be from an A15 or A7.
For CPUs not having the CBAR or boards with wrong information herein
we allow providing the base address as a configuration variable.
Now that we know the GIC address, we:
a) allow private interrupts to be delivered to the core
(GICD_IGROUPR0 = 0xFFFFFFFF)
b) enable the CPU interface (GICC_CTLR[0] = 1)
c) set the priority filter to allow non-secure interrupts
(GICC_PMR = 0xFF)
Also we allow access to all coprocessor interfaces from non-secure
state by writing the appropriate bits in the NSACR register.
The generic timer base frequency register is only accessible from
secure state, so we have to program it now. Actually this should be
done from primary firmware before, but some boards seems to omit
this, so if needed we do this here with a board specific value.
The Versatile Express board does not need this, so we remove the
frequency from the configuration file here.
After having switched to non-secure state, we also enable the
non-secure GIC CPU interface, since this register is banked.
Since we need to call this routine also directly from the smp_pen
later (where we don't have any stack), we can only use caller saved
registers r0-r3 and r12 to not mess with the compiler.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
If, in CONFIG_BOOTCOMMAND, the environment switches both the mmcdev
and bootpart variables to refer to MMC device 1, it would make sense
that the mmcroot env variable should switch to that device as well.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
dra7xx_evm has eMMC and the default environment can be stored in it.
So enabling saveenv command and the configs to store environment in eMMC.
Tested on DRA752 ES1.0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset,
the boot ROM sets the frequencies for OPP100. This patch attempts to
drop the frequencies back to OPP50 as soon as possible in the SPL. Then
later the voltages and frequencies up set higher.
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Adapt to current framework]
Signed-off-by: Tom Rini <trini@ti.com>
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on. In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed. In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.
Signed-off-by: Tom Rini <trini@ti.com>
We need to load 'imx6dl-sabresd.dtb' in the mx6dl version.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
In arch/arm/cpu/arm1136/cpu.c we have:
#ifndef CONFIG_SYS_CACHELINE_SIZE
#define CONFIG_SYS_CACHELINE_SIZE 32
#endif
,so there is no need to define 'CONFIG_SYS_CACHELINE_SIZE' with the default
size in the board config file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The wandboard solo version should boot the 'imx6dl-wandboard.dtb' file, since
dual-lite and solo variants are the same SoC with only the number of cores being
different.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add a driver for the TPS65910 PMIC that is found in the AM335x GP EVM,
AM335x EVM SK and others.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
[trini: Split and rework Avinash's changes into new drivers/power
framework]
Signed-off-by: Tom Rini <trini@ti.com>
Add a driver for the TPS65217 PMIC that is found in the Beaglebone
family of boards.
Signed-off-by: Greg Guyotte <gguyotte@ti.com>
[trini: Split and rework Greg's changes into new drivers/power
framework]
Signed-off-by: Tom Rini <trini@ti.com>
Since UBIFS is enabled for cpux9k2, more malloc space is needed.
For the current uboot 2013.10-rcX the size is to small, this will fix the
startup problems by increasing the malloc space to 4MiB.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Nicolas Colombain <nicolas.colombain@armadeus.com>
Add STMP3780-based Sansa Fuze+ board. This board is a small PMP
device sporting a CPU which was later rebranded to i.MX233 .
Currently supported is USB gadget mode and MMC .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Add STMP3780-based XFi3 board. This board is a small PMP device
sporting a CPU which was later rebranded to i.MX233 . Currently
supported is USB gadget mode and both external SD and internal
Phison SD-NAND bridge .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
LCD4 needs a slightly different GPIO configuration than the
original LWMON5 variant. GPIO49 needs to be configured to a
default output value of 0 (permanent voltage supply).
Additionally lcd4 also needs to enable the LSB transmitter.
Signed-off-by: Stefan Roese <sr@denx.de>
For most boards which define CONFIG_SPL_PAD_TO,
it is defined in config header files.
Currently, there exists only one exception, cam_enc_4xx board.
This patch moves CONFIG_SPL_PAD_TO definition
from board/ait/cam_enc_4xx/config.mk
to include/configs/cam_enc_4xx.h.
With this modification, we can delete a glue code
in the top level config.mk:
ifneq ($(CONFIG_SPL_PAD_TO),)
CPPFLAGS += -DCONFIG_SPL_PAD_TO=$(CONFIG_SPL_PAD_TO)
endif
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
libata already has similar functions as implemented in the ahci code.
Refactor the code to use the libata variants and remove the dependency on
ata.h. Convert some defines to use the version from libata.h. Also, remove
some unnecessary memset's of bss data.
This is a step toward hopefully merging ahci.c and dw_ahsata.c which are
essentially the same driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
gcc allows extensions to be non compiler specific by defining
__* macros for the attributes supported by gcc. Having a
different definition causes many warnings during the build
(cdefs.h on FreeBSD uses __attribute((__pure__)) where u-boot
uses __attribute__((pure)) for example). Do not redefine
these macros to suppress these warnings.
This patch ignores the checkpatch warning:
WARNING: __packed is preferred over __attribute__((packed))
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Somewhere along the line of refactoring the am335x header files, the
kernel image load was lost, so put it back in.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Separating the configuration file for Virtual
Target and real hardware Cyclone V development kit
Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
This adds the "test_compression" command when building the sandbox. This
tests the existing compression and decompression routines for simple
sanity and for buffer overflow conditions.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add mkimage support for generating and verifying MXS bootstream.
The implementation here is mostly a glue code between MXSSB v0.4
and mkimage, but the long-term goal is to rectify this and merge
MXSSB with mkimage more tightly. Once this code is properly in
U-Boot, MXSSB shall be deprecated in favor of mkimage-mxsimage
support.
Note that the mxsimage generator needs libcrypto from OpenSSL, I
therefore enabled the libcrypto/libssl unconditionally.
MXSSB: http://git.denx.de/?p=mxssb.git;a=summary
The code is based on research presented at:
http://www.rockbox.org/wiki/SbFileFormat
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
This patch add new functions to pmic max77686 to set voltage and mode.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Arndale board is based on samsung's exynos5250 soc.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Re-group the general options to note things that can be removed safely
to reduce binary size when not required, and expand the comment about
what commands we do include to note it could be replaced with a specific
list of required one. While at it, move the CMD parts of various
blocks IP to the end of the list for consistency.
Signed-off-by: Tom Rini <trini@ti.com>
After examining both TRMs and doing some experimentation, we can rely on
using the start of the download area for CONFIG_SPL_TEXT_BASE and then
move SRAM_SCRATCH_SPACE_ADDR up, just like am335x. This is required for
peripheral boot modes such as UART.
Signed-off-by: Tom Rini <trini@ti.com>
We only need this library when we're doing "disk" access to MMC/SD.
Update comment around the rest of CONFIG_SPL_LIB* to note that the
others are always required.
Signed-off-by: Tom Rini <trini@ti.com>
We had been allowing the max size to be larger than actually allowed by
the ROM. Expand the commentary here to explain why we set these
locations.
Signed-off-by: Tom Rini <trini@ti.com>
Now that IGEP base boards default environment use
the bootz command to boot a zImage instead of a
uImage, it makes sense to add support to supply a
raw initrd image to the kernel if needed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Use CONFIG_MACH_TYPE generic macro to set the machine type
number in the common arm code instead of setting it in the
board code.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Since config.mk is deprecated, remove this file,
and move CONFIG_SYS_TEXT_BASE define to config file.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since config.mk is deprecated, remove this file,
and move CONFIG_SYS_TEXT_BASE define to config file.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
With the new include structure for TI platforms, we need to not define
our own CONFIG_SYS_PROMPT and also need to include
<configs/omap5_common.h> much sooner, so do both of these. Also drop
the unused CONFIG_NET_MULTI
Signed-off-by: Tom Rini <trini@ti.com>
Update the Makefiles so that all boards can use the same spl generation tool
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
updating an ubi partition needs a completely erased mtd partition,
see:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035416.html
So, add partubi alt setting for the dfu_alt_info environment
variable to mark this partition as an ubi partition. In case we
update an ubi partition, we erase after flashing the image into the
partition, the remaining sektors.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Add the USB ehci support for the OMAP5 uEVM.
Configure the uEVM mux data
Add the flags to build the appropriate modules
Add the usb call backs to initialize the EHCI controller
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Andre Przywara
Robert P. J. Day
Lokesh Vutla
Steve Kipisz
Tom Rini
Fabio Estevam
Philip, Avinash
Greg Guyotte
Jens Scharsig (BuS Elektronik)
trem
Marek Vasut
Stefan Roese
Masahiro Yamada
Rob Herring
Jeroen Hofstee
Chin Liang See
Bo Shen
Kees Cook
Piotr Wilczek
Chander Kashyap
Heiko Schocher
Javier Martinez Canillas
Oleksandr Tyshchenko
Minkyu Kang
Dan Murphy