Make it similar to the code in mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Make it similar to the code in mips64/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips64/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The t4 register already holds the cache
line size, and the value of the register
is not changed in mips_init_icache.
Get the cache line size value from t4 for
mips_init_dcache as well and remove the
superfluous assignment of t5 register.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
The MIPS code uses centralized u-boot.lds script already,
and dynamic relocation is supported as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Checking mips32/time.c with checkpatch.pl shows this:
arch/mips/cpu/mips32/time.c:30: WARNING: line over 80 characters
arch/mips/cpu/mips32/time.c:57: ERROR: return is not a function, parentheses are not required
total: 1 errors, 1 warnings, 0 checks, 85 lines checked
Fix the code to make checkpatch.pl happy.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Qemu emulates a PCNET PCI card for the Malta CoreLV board.
Enable the pcnet driver and add board specific ethernet
initialization function to bring it up. Also enable the
CONFIG_CMD_NET and CONFIG_CMD_PING options.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Qemu emulates the Galileo GT64120 System Controller
which provides a CPU bus to PCI bus bridge.
The patch adds driver for this bridge and enables
PCI support for the emulated Malta board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Move the GT64120 register base to 0x1be00000
and setup PCI BAR registers as done by the
original YAMON bootloader.
This is needed for running Linux kernel.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The MIPS Malta board has a SOFTRES register. Writing a
magic value into that register initiates a board reset.
Use this feature to implement reset support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Add minimal support for the MIPS Malta CoreLV board
emulated by Qemu. The only supported peripherial is
the UART.
This is enough to boot U-Boot to the command prompt
both in little and big endian mode.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
On the origial Malta boards the REVISION register is
accessible at the 0x1fc00010 address. The contents of
this register gives information about the revision
of the Malta and Core Boards.
This register is used by the Linux kernel to identify
the actual board it is running on. However the register
is not emulated properly by Qemu, so put a hardcoded
value into the flash to make Linux work.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The Linux specific register access macros, the
extern function declarations and the UL suffixes
has been removed.
The header file will be used for the qemu-malta
board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The pcnet driver uses the pci_phys_to_mem function
to get the memory address of the DMA buffers. This
This assumes an 1:1 mapping between the PCI and
physical memory which is not true on all platforms.
On MIPS platform U-Boot is running within a mapped
memory region, and the pci_phys_to_mem macro can't
be used to obtain the memory address of the buffers.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Like many other projects, U-Boot has a tradition of including big
blocks of License headers in all files. This not only blows up the
source code with mostly redundant information, but also makes it very
difficult to generate License Clearing Reports. An additional problem
is that even the same lincenses are referred to by a number of
slightly varying text blocks (full, abbreviated, different
indentation, line wrapping and/or white space, with obsolete address
information, ...) which makes automatic processing a nightmare.
To make this easier, such license headers in the source files will be
replaced with a single line reference to Unique Lincense Identifiers
as defined by the Linux Foundation's SPDX project [1]. For example,
in a source file the full "GPL v2.0 or later" header text will be
replaced by a single line:
SPDX-License-Identifier: GPL-2.0+
We use the SPDX Unique Lincense Identifiers here; these are available
at [2].
Note: From the legal point of view, this patch is supposed to be only
a change to the textual representation of the license information,
but in no way any change to the actual license terms. With this patch
applied, all files will still be licensed under the same terms they
were before.
Note 2: The apparent difference between the old "COPYING" and the new
"Licenses/gpl-2.0.txt" only results from switching to the upstream
version of the license which is differently formatted; there are not
any actual changes to the content.
Note 3: There are some recurring questions about linense issues, such
as:
- Is a "All Rights Reserved" clause a problem in GPL code?
- Are files without any license header a problem?
- Do we need license headers at all?
The following excerpt from an e-mail by Daniel B. Ravicher should help
with these:
| Message-ID: <4ADF8CAA.5030808@softwarefreedom.org>
| Date: Wed, 21 Oct 2009 18:35:22 -0400
| From: "Daniel B. Ravicher" <ravicher@softwarefreedom.org>
| To: Wolfgang Denk <wd@denx.de>
| Subject: Re: GPL and license cleanup questions
|
| Mr. Denk,
|
| Wolfgang Denk wrote:
| > - There are a number of files which do not include any specific
| > license information at all. Is it correct to assume that these files
| > are automatically covered by the "GPL v2 or later" clause as
| > specified by the COPYING file in the top level directory of the
| > U-Boot source tree?
|
| That is a very fact specific analysis and could be different across the
| various files. However, if the contributor could reasonably be expected
| to have known that the project was licensed GPLv2 or later at the time
| she made her contribution, then a reasonably implication is that she
| consented to her contributions being distributed under those terms.
|
| > - Do such files need any clean up, for example should we add GPL
| > headers to them, or is this not needed?
|
| If the project as a whole is licensed under clear terms, you need not
| identify those same terms in each file, although there is no harm in
| doing so.
|
| > - There are other files, which include both a GPL license header
| > _plus_ some copyright note with an "All Rights Reserved" clause. It
| > has been my understanding that this is a conflict, and me must ask
| > the copyright holders to remove such "All Rights Reserved" clauses.
| > But then, some people claim that "All Rights Reserved" is a no-op
| > nowadays. License checking tools (like OSLC) seem to indicate this is
| > a problem, but then we see quite a lot of "All rights reserved" in
| > BSD-licensed files in gcc and glibc. So what is the correct way to
| > deal with such files?
|
| It is not a conflict to grant a license and also reserve all rights, as
| implicit in that language is that you are reserving all "other" rights
| not granted in the license. Thus, a file with "Licensed under GPL, All
| Rights Reserved" would mean that it is licensed under the GPL, but no
| other rights are given to copy, modify or redistribute it.
|
| Warm regards,
| --Dan
|
| Daniel B. Ravicher, Legal Director
| Software Freedom Law Center (SFLC) and Moglen Ravicher LLC
| 1995 Broadway, 17th Fl., New York, NY 10023
| (212) 461-1902 direct (212) 580-0800 main (212) 580-0898 fax
| ravicher@softwarefreedom.org www.softwarefreedom.org
[1] http://spdx.org/
[2] http://spdx.org/licenses/
Signed-off-by: Wolfgang Denk <wd@denx.de>
The problem here is that uboot can't mount ext4 filesystem with
commit "50ce4c07df1" applied. We use hard-coded "SECTOR_SIZE"(512)
before this commit, now we introduce (block_dev_desc_t *)->log2blksz
to replace this macro. And after we calling do_ls()->fs_set_blk_dev(),
the variable log2blksz is not initialized, which it's not correct.
And this patch try to solve the problem by caculating the value of
log2blksz from variable blksz.
Fix reading ext4_extent_header struture on BE machines. Some 16 bit
fields where converted to 32 bit fields, due to the byte swap on BE
machines the containing value was corrupted. Therefore reading ext4
filesystems on BE machines where broken before.
Signed-off-by: Rommel Custodio <sessyargc+uboot@gmail.com>
[sent via git-send-email; rework commit message]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
As both the DDR SDRAM and NAND flash connect to EBI on at91sam9n12
and share the lower 8 bits data line. If use low drive of the data
line, it will cause DDR data access corrupt in lower address, so
change the data line to high drive mode
This will fix the Linux kernel boot issue when use Lower address
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
The old value of 0x000e0030 will cause ethernet
timeout issues on the sabrelite and possibly other
boards using the KSZ9021.
I have no explanation as to why.
But this is a correct change, the TRM will be updated
to show that 00b is the only valid setting for bits
19-18 of DRAM_RESET.
My thanks go to Liu Hui(Jason) for this information.
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Commit de1d786e (add support for Xilinx 1000BASE-X phy (GTX)) introduced the
checking for ESTATUS_1000_XHALF, but it incorrectly sets the
SUPPORTED_1000baseX_Full flag in this case.
Set the SUPPORTED_1000baseX_Half flag instead.
Acked-by: Charles Coldwell <coldwell@gmail.com>
Reviewed-By: Sascha Silbe <t-uboot@infra-silbe.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
de1d786 [add support for Xilinx 1000BASE-X phy (GTX)] introduced a
check for the extended status register in order to support
1Gbps-capable PHYs that don't have the 1000BASE-T registers. Since
Extended Status only indicates what the PHY (i.e. the local side) is
capable of, this broke communication with non-1Gbps peers.
Only check the extended status if the 1000BASE-T registers are
actually missing so we don't end up setting speed to 1Gbps even though
the previous test (for the combination of local and peer support for
1Gbps) already indicated we can't do 1Gbps with the current peer.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The value of this config variable is not available to image.h on the host,
since the board config is not actually included. Bring this in so that
mkimage will be built with image-signing support for sandbox at least.
Signed-off-by: Simon Glass <sjg@chromium.org>
Missing space for loaddtb command has been added. When missing, ext4load
fails with wrong number of passed parameters.
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Before the bootm refactor, fixup_silent_linux() was done only in the
monolithic bootm case, not in the subcommand case. With the refactor, it
is done always, which is good. Unfortunately it is done too late, since it
is the PREP or CMDLINE stages that set up the command line for Linux.
Move fixup_silent_linux() into the LOADOS stage, which is where we find
out the OS being used, and can thus decide whether to perform this step.
Signed-off-by: Simon Glass <sjg@chromium.org>
commit 54965b6136 (README: mxs: Introduce README.mxs) should have changed the
file name to README.mxs, as it covers both mx23 and mx28 now.
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Dealing with the sys ctrl register should touch only the
relevant bits and not accidently the whole register. On i.MX6,
the sys control register contains bits which shouldn't be reset to
0, e.g. SYS_CTRL[3-0] and IPP_RST_N (SYS_CTRL[23]).
Do this by read/modify/write instead of just a 32bit write.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. No contents of "asm/arch/clk.h" is used within "dw_mmc.c".
2. If arch doesn't have "asm/arch/clk.h" driver won't build.
Without mentioned inclusion dw_mmc driver could be built for arches
other than ARM. For ARM driver still builds without it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fill the right command type when using CMD12 to stop data transfer.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
CONFIG_SPL_BUILD creates debug TLB entry, so disable it before init_tlbs.
CONFIG_SPL_INIT_MINIMAL never creates any debug TLB entry, so no need
of disable_tlb().
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The gdsys ControlCenter Digital board is based on a Freescale P1022 QorIQ SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2x GbE
- Lattice ECP3 FPGA connected via PCIe
- mSATA RAID1
- USB host
- DisplayPort video output
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
MAKEALL is fine for ppc4xx and mpc85xx.
Run checks were done on our controlcenterd hardware.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Atmel TPM devices with two wire interface.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
if alen is 0: no longer start a write cycle before reading data.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Extend the tpm library with support for single authorized (AUTH1) commands
as specified in the TCG Main Specification 1.2. (The internally used helper
functions are implemented in a way that they could also be used for double
authorized commands if someone needs it.)
Provide enums with the return codes from the TCG Main specification.
For now only a single OIAP session is supported.
OIAP authorized version of the commands TPM_LoadKey2 and TPM_GetPubKey are
provided. Both features are available using the 'tpm' command, too.
Authorized commands are enabled with CONFIG_TPM_AUTH_SESSIONS. (Note that
this also requires CONFIG_SHA1 to be enabled.)
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Before setting: mipi_lcd_device.reverse_panel = 1, the Trats's LCD panel
was flipped by 180 degrees.
The flip was caused by following change:
Exynos: Change get_timer() to work correctly
SHA1: 3d00c0cb96
This commit fixed udelay(), which is necessary (due to HW LCD controller
oddity) for mipi-dsi correct operation. As a result the display orientation
has been switched.
As a follow up, the hwrevision() function has been removed, since it was
used only in this particular place.
Test HW: Trats Exynos4210 rev 0.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Provide proper setting for the APLL fout frequency calculation for
Exynos4 based targets (especially Exynos4210 - Trats board).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Fix:
mpc8323erdb.c: In function 'mac_read_from_eeprom':
mpc8323erdb.c:198:3: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Timur Tabi <timur@tabi.org>
cc: Kim Phillips <kim.phillips@freescale.com>
Gabor Juhos
Tom Rini
Wolfgang Denk
Lan Yixun (dlan)
Rommel Custodio
Bo Shen
Troy Kisky
Fabio Estevam
Sascha Silbe
Simon Glass
Łukasz Majewski
Dirk Behme
Alexey Brodkin
Haijun.Zhang
Prabhakar Kushwaha
Dirk Eibach
Reinhard Pfau