Add Kconfig option to support loading PPA header from eMMC/SD and
NAND Flash.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The PPA is a EL3 firmware, which support PSCI, hotplug,
power-management features etc.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The PPA is a EL3 firmware, which support PSCI, hotplug,
power-management features etc.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since commit ce412b7, RGMII TX clock internal delay is not enabled
for AR8033 unconditionally. On LS1021ATWR board, the third port
eTSEC3 uses AR8033 in RGMII mode. The TX/RX internal delay needs to
be enabled.
This patch will set PHY_INTERFACE_MODE_RGMII_ID to enable RGMII TX/RX
clock internal delay for AR8033 on the third port.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently $fdtfile is constructed from CONFIG_DEFAULT_TREE, containing
the filename. However on arm64 that file is located in an allwinner
subdirectory.
To avoid the need for users/distros symlinking the .dtb files, prepend
the vendor directory for ARM64.
This aligns Pine64 with other boards such as Raspberry Pi 3.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Before this patch, CONFIG_SYS_BOOTPARAMS_LEN was the same size as
CONFIG_SYS_MALLOC_LEN. So, if malloc() had previously been called, and
initr_malloc_bootparams() was called, it would fail with an out-of-
memory error. This patch fixes this issue by expanding the malloc pool
to 256KB.
Signed-off-by: Kyle Edwards <kyleedwardsny@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This fixes an issue with the saveenv command causing U-Boot to no
longer work on the QEMU Mips pseudoboard. Because the offset of the
environment was being determined by CONFIG_SYS_MONITOR_LEN, and this
value was less than the actual size of U-Boot, saveenv was overwriting
parts of the U-Boot code. Because CONFIG_SYS_MONITOR_LEN is no longer
used on MIPS, this patch removes it and places the environment at the
end of the pseudoboard's 4MB flash.
Signed-off-by: Kyle Edwards <kyleedwardsny@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we have now V3s support in board code, the V3s DTSI file should also
be added.
Add also some CCU include headers to satisfy the DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Basic U-Boot support is now present for V3s.
Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.
As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Use - instead of @ for OPP tables
- Add input-delay properties to Cadence eMMC nodes
- Restore full license text because code-diff is annoying
- Fix NAND compatible strings
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The SCP (System Control Processor) or what we call STM (Stand-by
MPU) is integrated in LD4, Pro4, sLD8, LD6b, LD11, and LD20.
For these SoCs, show the information if STM is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This configuration is supposed to be used with ARM Trusted Firmware,
so the SYSTEM_RESET is implemented in BL31. Invoke PSCI instead of
U-Boot's own reset code because we need to coordinate with SCP
(System Control Processor) for the system-level power management.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is needed for HDMI, which will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Video driver for older Allwinner SoCs uses cfb console framework which
in turn uses struct ctfb_res_modes to hold timing informations. However,
DM video framework uses different structure - struct display_timing.
It makes more sense to convert lcdc to use new timing structure because
all new drivers should use DM video framework and older drivers might be
rewritten to use new framework too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
TCON unit has similar layout and functionality also on newer SoCs. This
commit splits out TCON code for easier reuse later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.
This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40's CPU controls are a combination of sun6i and sun7i.
All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.
Last, the R40 does not have a secure SRAM block.
This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 has the CPUCFG block at the same address as the A20.
Fix it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can do DRAM initialization for the R40, we can enable
SPL support for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 seems to have a variant of the memory controller found in
the H3 and A64 SoCs. Adapt the code for use on the R40. The changes
are based on released DRAM code and comparing register dumps from
boot0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PIO on the R40 SoC is mostly compatible with the A20.
Only a few pin functions for mmc2 were added to the PC
pingroup, to support 8 bit eMMCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These values were taken from the Banana Pi M2 Ultra fex file
found in the released vendor BSP. This is the only publicly
available R40 device at the time of this writing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the BSP released by Banana Pi, the R40 (sun8iw11p1) has
an extra "PLL lock control" register in the CCU, which controls whether
the individual PLL lock status bits in each PLL's control register work
or not.
This patch enables it for all the PLLs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PIO is generally compatible with the A20, except that it routes the
full 8 bits and eMMC reset pins for mmc2.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The watchdog found on the R40 SoC is the older variant found on the A20.
Add the proper "#if defines" to make it work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 SoC uses the AXP221s in I2C mode to supply power.
Some regulator's common usages have changed, and also the recommended
voltage for existing usages have changed. Update the defaults to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 is the successor to the A20. It is a hybrid of the A20, A33
and the H3.
The R40's PIO controller is compatible with the A20,
Reuse the A20 UART and I2C muxing code by adding the R40's macro.
The display pipeline is the newer DE 2.0 variant.
Block enabling video on R40 for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently we have some lines in board/sunxi/Kconfig that are very long.
These line either provide default values for a set of SoCs, or limit
some option to a subset of sunxi SoCs.
Fortunately Kconfig makes it easy to split them. The Kconfig language
document states
If multiple dependencies are defined, they are connected with '&&'.
This means we can split existing dependencies at "&&" symbols. This
applies to both the "depends on" lines and "if" expressions.
This patch splits them up to one symbol per line. This will make it
easier to add, remove, or modify one item at a time.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONS_INDEX configuration to Kconfig.
Update sunxi's defconfigs to remove SYS_EXTRA_OPTIONS variable not
needed anymore.
Default value is 1 except for sun5i (equals 2) and sun8i (equals 5).
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
[Maxime: Added a depends on ARCH_SUNXI to avoid build breakages]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONFIG_MACPWR to Kconfig and update all the sunxi defconfigs
that used it in SYS_EXTRA_OPTIONS.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONFIG_SATAPWR into kconfig.
Thanks to that, many SYS_EXTRA_OPTIONS can be removed from some
defconfigs.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to
update defconfig files of SYS_EXTRA_OPTIONS accordingly and
remove it when it is possible.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the SUNXI_EMAC config to Kconfig. Remove it from SYS_EXTRA_OPTIONS
from many sunxi defconfig and renamed it into SUN4I_EMAC to not confuse it
with SUN8I_EMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB_EHCI configuration is already set in this defconfig
using kconfig's config. This configuration in SYS_EXTRA_OPTIONS
must be removed and so the SYS_EXTRA_OPTIONS.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This configuration is not necessary in a defconfig file so
it is removed from the SYS_EXTRA_OPTIONS.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Remove the AXP209_POWER option from SYS_EXTRA_OPTIONS.
As this configuration already exists on Kconfig, we just need
to remove it from defconfig.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the SUNXI_GMAC config option to Kconfig, remove it
from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At present if the return to bootrom fails (e.g. because you are not using
the Rockchip's bootrom's pointer table in MMC) then the board prints
SPL message and hangs. Print a message first if we can, to help in
understanding what happened when it hangs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
'A || (!A && B)' is equivalent to 'A || B'.
Let's reduce the complexity of the statement in start_jr0().
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After allocating sata->cmd_hdr_tbl_offset we have to check
this variable and not variable sata.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
(pdimm[0].data_width >= 32) || (pdimm[0].data_width <= 40)
is always true.
We should use && here.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg
Hou Zhiqiang
Santan Kumar
Alison Wang
Andreas Färber
Kyle Edwards
Icenowy Zheng
Masahiro Yamada
Jernej Skrabec
Chen-Yu Tsai
Mylène Josserand
Tom Rini
Simon Glass
xypron.glpk@gmx.de