Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This value is not used by the network stack and is available in the
global data, so stop passing it around. For the one legacy function
that still expects it (init op on old Ethernet drivers) pass in the
global pointer version directly to avoid changing that interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license. However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word. I'd prefer
to be consistent to this end".
Change the license IDs to use the official name.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
Fix:
4xx_enet.c: In function 'ppc_4xx_eth_initialize':
4xx_enet.c:2029: warning: assignment from incompatible pointer type
Tested on sequoia board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix:
4xx_enet.c: In function 'ppc_4xx_eth_init':
4xx_enet.c:875:6: warning: variable 'ethgroup' set but not used [-Wunused-but-set-variable]
I used "__maybe_unused" here intentionally, since all other
alternatives to fix this compilation warning would result in more
ifdef's.
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
4xx_enet.c: In function 'enet_rcv':
4xx_enet.c:1772:21: warning: variable 'ef_ptr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
4xx_enet.c: In function 'ppc_4xx_eth_init':
4xx_enet.c:1352: warning: format '%08x' expects type 'unsigned int', but
argument 2 has type 'volatile struct mal_desc_t *'
4xx_enet.c:1352: warning: format '%08x' expects type 'unsigned int', but
argument 3 has type 'volatile struct mal_desc_t *'
4xx_enet.c:1365: warning: format '%08lx' expects type 'long unsigned int', but
argument 3 has type 'unsigned int'
4xx_enet.c:1376: warning: format '%08lx' expects type 'long unsigned int', but
argument 3 has type 'unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
This is long over due. All but two net drivers have been converted, but
those have now been dropped.
The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined. So here we scrub the
core code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Only install der 4xx-EMAC interrupt handlers *after* the core
network driver is registered.
This problem was noticed on the APM Taishan 440GX board, where
the board hung upon bootup after displaying "Net:".
Signed-off-by: Stefan Roese <sr@denx.de>
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch starts a bit PPC4xx header cleanup. First patch mostly
touches PPC440 files. A later patch will touch the PPC405 files as well.
This cleanup is done by creating header files for all SoC versions and
moving the SoC specific defines into these special headers. This way the
common header ppc405.h and ppc440.h can be cleaned up finally.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some ppc4xx related headers from the common include
directory (include/) to the powerpc specific one
(arch/powerpc/include/asm/). This way to common include directory is not
so cluttered with files.
Signed-off-by: Stefan Roese <sr@denx.de>
The driver name does not need to be writable, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
By defining CONFIG_M88E1111_DISABLE_FIBER boards can configure the
M88E1111 PYH to disable fiber. This is needed for an upcoming PPC460GT
based board, which has fiber/copper auto-selection enabled by default.
This doesn't seem to work. So we disable fiber in the PHY register.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Modify all existing *.c files to use the new register names
as seen in the AMCC manuals.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
On 405EZ the RX-/TX-interrupts are coalesced into one IRQ bit in the
UIC. We need to acknowledge the RX-/TX-interrupts in the
SDR0_ICINTSTAT reg as well.
This problem was introduced with commit
d1631fe1 [ppc4xx: Consolidate PPC4xx UIC defines]
Signed-off-by: James Clough <james@rtetc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:
- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines
Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:
- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines
Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.
Signed-off-by: Stefan Roese <sr@denx.de>
It was brought to our attention that U-Boot contains code derived from the
IBM OpenBIOS source code originally provided with some of the older PowerPC
4xx development boards. As a result, the original license of this code has
been carried in the various files for a number of years in the U-Boot project.
IBM is dual-licensing the IBM code contributions already present in U-Boot
under either the terms of the GNU General Public License version 2, or the
original code license already present.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch fixes a compilation warning for some Ethernet PHY-less
PPC4xx platforms (440SPE based ones) and a potential compilation
error for 440SP platforms (use of undefined 'ethgroup' variable).
In the original code and in case of 440SPE platforms, 'ethgroup'
is initialized to -1 and never modified. Later in the function,
within an #ifdef statement, an 'if statement' executes code only
if 'ethgroup' is set to 4, therefore it is harmless to avoid
executing the 'if statement' by removing the CONFIG_440SPE from
the affected #ifdefs. In case of 440SP platforms with on-board
Ethernet PHY, 'ethgroup' is undefined but used (there are not such
platforms in the repository yet). All other architectures are not
affected by this change.
Signed-off-by: Alessio Centazzo acpatin@yahoo.com
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch fixes MDIO clock setup in case when OPB frequency is 100MHz.
Current code assumes that the value of sysinfo.freqOPB is 100000000
when OPB frequency is 100MHz. In reality it is 100000001. As a result
MDIO clock is set to incorrect value, larger than 2.5MHz, thus violating
the standard. This in not a problem on boards equipped with Marvell PHYs
(e.g. Canyonlands), since those PHYs support MDIO clocks up to 8.3MHz,
but can be a problem for other PHYs (e.g. Realtek ones).
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
The drivers that get converted here:
3c589
4xx_enet
dc2114x
dm9000x
enc28j60
fsl_mcdmafec
ks8695eth
mcffec
rtl8019
rtl8169
s3c4510b_eth
xilinx_emac
xilinx_emaclite
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Rolf Offermanns <rof@sysgo.de>
CC: Stefan Roese <sr@denx.de>
CC: Sascha Hauer <saschahauer@web.de>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
CC: Greg Ungerer <greg.ungerer@opengear.com>
CC: Xue Ligong <lgxue@hotmail.com>
CC: Masami Komiya <mkomiya@sonare.it>
CC: Curt Brune <curt@cucy.com>
CC: Michal SIMEK <monstr@monstr.eu>
Also changed path in all linker scripts that reference this driver
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
All in-tree IBM/AMCC PPC4xx boards using the EMAC get this new CONFIG
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Since this define is only used on one board that was never really in
production, removing this compile time option doesn't hurt and makes
the code more readable.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a compilation warning for the PIP405 board. It moves the
#ifndef CONFIG_CS8952_PHY define a little so that the warning doesn't
occur anymore. I am a little unsure if this #ifdef is at the correct
place now or if it could be removed completely. This needs to get
tested on the PIP405 board.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds GPCS, SGMII and M88E1112 PHY support
for the AMCC PPC460GT/EX processors.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch reworks the 440GX interrupt handling so that the common 4xx
code can be used. The 440GX is an exception to all other 4xx variants
by having the cascading interrupt vectors not on UIC0 but on a special
UIC named UICB0 (UIC Base 0). With this patch now, U-Boot references
the 440GX UICB0 when UIC0 is selected. And the common 4xx interrupt
handling is simpler without any 440GX special cases.
Also some additional cleanup to cpu/ppc4xx/interrupt.c is done.
Signed-off-by: Stefan Roese <sr@denx.de>
This 2nd patch now removes all UIC mask bit definition. They should be
generated from the vectors by using the UIC_MASK() macro from now on.
This way only the vectors need to get defined for new PPC's.
Also only the really used interrupt vectors are now defined. This makes
definitions for new PPC versions easier and less error prone.
Another part of this patch is that the 4xx emac driver got a little
cleanup, since now the usage of the interrupts is clearer.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is the first step to consolidate the UIC related defines in the
4xx headers. Move header from asm-ppc/ppc4xx-intvec.h to
asm-ppc/ppc4xx-uic.h as it will hold all UIC related defines in the next
steps.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for placing the RGMII bridge on the
PPC405EX(r) into MII/GMII mode and allows a board-specific
configuration to specify the bridge mode at compile-time.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes ppc4xx related printf format warning. Those warnings are
now visible since patch dc4b0b38d4
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.
Signed-off-by: Stefan Roese <sr@denx.de>
Currently U-Boot crashes in ppc_4xx_eth_init on sequoia
with cache enabled (TLB Parity exeption). This patch
fixes the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch fixes a problem with the RGMII setup of the 460GT. The 460GT
has 2 RGMII instances and we need to configure the 2nd RGMII instance
for the EMAC2+3 channels.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Currently EMAC2+3 are not working. This will be fixed in a later
release.
Signed-off-by: Stefan Roese <sr@denx.de>
The 405EZ only supports 512 bytes of rx-/tx-fifo EMAC sizes. But
currently 4k/2k is configured. This patch fixes this issue.
Thanks to Thomas Kindler <tkindler@lenord.de> for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
U-Boot crashes in the net loop if CONFIG_4xx_DCACHE is
enabled. To reproduce the problem ensure that 'ethrotate'
environment variable isn't set to "no" and then run
"tftp 200000 not_existent_file".
This patch tries to fix the issue.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch allows the use of 4xx interrupt vector number defines
in board specific code outside cpu/ppc4xx.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
flush + invalidate_dcache_range() expect the start and stop+1 address.
So the stop address is the first address behind (!) the range.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch removes some redundant code and decrements the end
address of cache flush and invalidate by 1.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
I lately noticed, that newer 4xx board with GBit support sometimes don't
finish link autonegotiation in 4 seconds. Changing this timeout to 5
seconds seems fine here.
Signed-off-by: Stefan Roese <sr@denx.de>
Vagrant Cascadian
Joe Hershberger
Wolfgang Denk
Anatolij Gustschin
Stefan Roese
Marek Vasut
Mike Frysinger
Mike Williams
Niklaus Giger
James Clough
Josh Boyer
Alessio Centazzo
Ben Warren
Felix Radensky
Jean-Christophe PLAGNIOL-VILLARD
Victor Gallardo
Grant Erickson
Matthias Fuchs