Kilauea has an AT24C02 EEPROM which has an 8 byte page. Without defining
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS to 3 the "eeprom" command doesn't
work correctly.
Additionally the page write delay (CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
is set to a more defensive value of 10ms.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a generic command for programming I2C bootstrap
eeproms on PPC4xx. An implementation for Canyonlands board is
included.
The command name is intentionally chosen not to be PPC4xx specific.
This way other CPU's/SoC's can implement a similar command under
the same name, perhaps with a different syntax.
Usage on Canyonlands:
=> chip_config
Available configurations (I2C address 0x52):
600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100
600-nand - NAND CPU: 600 PLB: 200 OPB: 100 EBC: 100
800-nor - NOR CPU: 800 PLB: 200 OPB: 100 EBC: 100
800-nand - NAND CPU: 800 PLB: 200 OPB: 100 EBC: 100
1000-nor - NOR CPU:1000 PLB: 200 OPB: 100 EBC: 100
1000-nand - NAND CPU:1000 PLB: 200 OPB: 100 EBC: 100
1066-nor - NOR CPU:1066 PLB: 266 OPB: 88 EBC: 88 ***
1066-nand - NAND CPU:1066 PLB: 266 OPB: 88 EBC: 88
=> chip_config 600-nor
Using configuration:
600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100
done (dump via 'i2c md 52 0.1 10')
Reset the board for the changes to take effect
Other 4xx boards will be migrated to use this command soon
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards. Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The XPedite1000 only has 2 available ethernet ports:
ppc_4xx_eth2 (EMAC2) and ppc_4xx_eth3 (EMAC3)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously an I2C EEPROM was used. The EEPROM had size, reliability,
and access issues which are resolved by storing the environment in
flash.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable GPIO pins for an I2C EEPROM write protect, a system reset pin,
and a PMC #MONARCH pin. These pins are not currently used in U-Boot,
but are used in OSes and may be used in U-Boot in the future.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The XPedite1000 can be built with 4 total flashes:
- 512KB AMD socketed
- 16MB Intel soldered
- 2 x 32MB AMD MirrorBit flashes
Add support for the optional 2 32MB CFI-compliant AMD flashes
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
By default, the XPedite1000 comes installed with xMon, a proprietary
bootloader. xMon stores its MAC address in an onboard EEPROM. Rather
than requiring a non-standard location in the EEPROM to be reserved for
MAC addresses, store the MAC addresses in U-Boot's standard environment.
A U-Boot application or OS application can be used to migrate xMon MAC
addresses to U-Boot's environment if necessary.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
All XPedite1000's have SPD EEPROMs present and no fixed configuration
parameters are currently defined or used
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Using the CFI flash driver will allow write access to the 16MB Intel
StrataFlash present on the XPedite1000. The 512KB socketed (non
CFI-compliant flash) will no longer be writable.
The mapping of the 16MB Strata flash was moved to 0xff000000 and the
512KB AMD socketed flash was moved to 0xfe000000.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
In cpu/ppc4xx/speed.c initialization of sysInfo->freqOPB for 405EP was
left out for no obvious reason.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Patch d873133f [ppc4xx: Add Sequoia RAM-booting target] broke "normal"
booting on some 44x platforms. This breakage is only noticed in some
cases while powercycling. As it seems, the code in question in start.S
didn't invalidate TLB #0. This makes sense since this TLB is used for
the bootrom mapping. With the patch mentioned above even TLB #0 got
invalidated resulting in an error later on.
This patch now fixes this issue by only invalidating TLB #0 in the RAM-
booting case.
Tested succesfully on Sequoia and Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <Eibach@gdsys.de>
By including autoconf.mk before config.mk, all top level files can use any
config options it sets up (like <arch>_config.mk) or the Makefile itself
without being forced to use lazy evaluation.
This patch removes the static declaration from gunzip_bmp()
Without it, the gunzip_bmp() function is not visible to
common/lcd.c and fails to compile with an error.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
The top build system sets up HOSTCFLAGS a bit and exports it, but other
places use HOST_CFLAGS instead. Unify the two as HOSTCFLAGS so that the
values stay in sync.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds I2C support for mvBC-P and defines flash layout
matching the shipped product.
Signed-off-by: Andr Schwarz <andre.schwarz@matrix-vision.de>
ahci.c: In function 'ata_scsiop_read_capacity10':
ahci.c:616: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
biosemu.c: In function 'BE_setVGA':
biosemu.c:147: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously, non-e500 architectures only unlocked their data cache which
was used as early RAM when booting to Linux using the "bootm" command.
This change causes all PPC boards with CONFIG_SYS_INIT_RAM_LOCK defined
to unlock their data cache during U-Boot's initialization. This
improves U-Boot performance and provides a common cache state when
booting to different OSes.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch updates zlib to the latest stable version.
Only relevant zlib parts were ported to u-boot tree, as was done for
the previously used version of zlib (0.95). New zlib gives faster
inflate performance and other improvements, see www.zlib.net
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Reviewed-by: Angelo Castello <angelo.castello@st.com>
Edited commit message
Signed-off-by: Wolfgang Denk <wd@denx.de>
Linux's netconsole works much better when you can pass it the MAC address of
the server. (otherwise it just uses broadcast, which everyone else on my
network complains about :)
This sets the env var "serveraddr" (to match ethaddr), so that you can pass
it to linux with whatever bootargs you want to....
addnetconsole=set bootargs $(bootargs) netconsole=@$(ipaddr)/eth0,@$(serverip)/$(serveraddr)
Signed-of-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch fixes a compilation warning for some Ethernet PHY-less
PPC4xx platforms (440SPE based ones) and a potential compilation
error for 440SP platforms (use of undefined 'ethgroup' variable).
In the original code and in case of 440SPE platforms, 'ethgroup'
is initialized to -1 and never modified. Later in the function,
within an #ifdef statement, an 'if statement' executes code only
if 'ethgroup' is set to 4, therefore it is harmless to avoid
executing the 'if statement' by removing the CONFIG_440SPE from
the affected #ifdefs. In case of 440SP platforms with on-board
Ethernet PHY, 'ethgroup' is undefined but used (there are not such
platforms in the repository yet). All other architectures are not
affected by this change.
Signed-off-by: Alessio Centazzo acpatin@yahoo.com
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Fixed the DHCP/BOOTP/RARP regression introduced in u-boot-2009.06
by initializing our IP addr to 0 in order to accept any IP addr
assigned to us by the DHCP/BOOTP/RARP server.
Ack-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
With these fixes, this driver works properly for multi chip
addressging mode
Bugfixes:
1. Build error fixed for function mv88e61xx_busychk_multic-fixed
2. PHY dev address error detection- fixed
3. wrong busy bit was refered in function mv88e61xx_busychk -fixed
4. invalid data read ptr was refered for RD_PHY in case of
multichip addressing mode -fixed
The Multichip Address mode is tested with RD6281A board having
MV88E6165 switch on it
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The Marvell documentation for the 88f6281 states that the error coding
is only valid if the error summary and last frame bits in the transmit
descriptor status field are set. This patch adds checks for these for
transmit (I would get transmit errors on bootp with the current check,
which I believe are spurious).
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
kwgbe_send/recv both have loops waiting for the hardware to set a bit.
GCC 4.3.3 cleverly optimizes the send case to ... a while(1); loop. This
patch uses readl to force a read from device memory. Other volatile
accesses have also been replaced with readl/writel where appropriate
(as per suggestions on the U-boot mailing list).
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch sets the returned value to 0xFFFF if the PHY does not exist
and does not assert Transfer Acknowledge. A NULL check for the value
pointer is also added for buffer overflow protection.
Without this patch 'mii info' will show 'phantom' devices because the
value will be not be initialized and return with some random value.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_SMC911X* to CONFIG_SMC911X*
- cleaned up line lengths
- modified all boards that override weak function in this driver
- added
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
These PHYs are on P2020RDB platform.
Also revamped Freescale copyright message in drivers/net/tsec.c.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
On 04 Oct 2008 Pieter posted a dns implementation for U-Boot.
http://www.mail-archive.com/u-boot-users@lists.sourceforge.net/msg10216.html
>
> DNS can be enabled by setting CFG_CMD_DNS. After performing a query,
> the serverip environment var is updated.
>
> Probably there are some cosmetic issues with the patch. Unfortunatly I
> do not have the time to correct these. So if anybody else likes DNS
> support in U-Boot and has the time, feel free to patch it in the main tree.
Here it is again - slightly modified & smaller:
- update to 2009-06 (Pieter's patch was for U-Boot 1.2.0)
- README.dns is added
- syntax is changed (now takes a third option, the env var to store
the result in)
- add a random port() function in net.c
- sort Makefile in ./net/Makefile
- dns just returns unless a env var is given
- run through checkpatch, and clean up style issues
- remove packet from stack
- cleaned up some comments
- failure returns much faster (if server responds, don't wait for
timeout)
- use built in functions (memcpy) rather than byte copy.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
fix this gcc 4.4 warning:
tsec.c: In function 'tsec_init':
tsec.c:200: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Stefan Roese
Matthias Fuchs
Peter Tyser
Matthias Fuchs
Dirk Eibach
Wolfgang Denk
Mike Frysinger
Mark Jackson
Peter Tyser
André Schwarz
Kumar Gala
Detlev Zundel
Giuseppe CONDORELLI
Robin Getz
Ilya Yanok
Alessio Centazzo
Michael Zaidman
Prafulla Wadaskar
Simon Kagstrom
Richard Retanubun
Ben Warren
Poonam Aggrwal
Kim Phillips