Merge branch 'master' of git://git.denx.de/u-boot-pxa

MAKEALL

@@ -706,6 +706,7 @@ LIST_at91="			\
 
 LIST_pxa="		\
 	cerf250		\
+	colibri_pxa270	\
 	cradle		\
 	csb226		\
 	delta		\
@@ -715,10 +716,13 @@ LIST_pxa="		\
 	polaris		\
 	pxa255_idp	\
 	trizepsiv	\
+	vpac270_nor	\
+	vpac270_onenand	\
 	wepep250	\
 	xaeniax		\
 	xm250		\
 	xsengine	\
+	zipitz2		\
 	zylonite	\
 "
 

Makefile

@@ -2178,6 +2178,15 @@ trizepsiv_config	:	unconfig
 	fi;
 	@$(MKCONFIG) -n $@ -a trizepsiv arm pxa trizepsiv
 
+vpac270_nor_config \
+vpac270_onenand_config	: unconfig
+	@mkdir -p $(obj)include
+	@if [ "$(findstring onenand,$@)" ] ; then \
+		echo "#define CONFIG_ONENAND_U_BOOT" \
+			>>$(obj)include/config.h ; \
+	fi;
+	@$(MKCONFIG) -n $@ -a vpac270 arm pxa vpac270
+
 #########################################################################
 ## ARM1136 Systems
 #########################################################################

arch/arm/cpu/pxa/pxafb.c

@@ -112,6 +112,39 @@ vidinfo_t panel_info = {
 	vl_efw:		0,
 };
 #endif /* CONFIG_SHARP_LM8V31 */
+/*----------------------------------------------------------------------*/
+#ifdef CONFIG_VOIPAC_LCD
+
+# define LCD_BPP	LCD_COLOR8
+# define LCD_INVERT_COLORS
+
+/* you have to set lccr0 and lccr3 (including pcd) */
+# define REG_LCCR0	0x043008f8
+# define REG_LCCR3	0x0340FF08
+
+vidinfo_t panel_info = {
+	vl_col:		640,
+	vl_row:		480,
+	vl_width:	157,
+	vl_height:	118,
+	vl_clkp:	CONFIG_SYS_HIGH,
+	vl_oep:		CONFIG_SYS_HIGH,
+	vl_hsp:		CONFIG_SYS_HIGH,
+	vl_vsp:		CONFIG_SYS_HIGH,
+	vl_dp:		CONFIG_SYS_HIGH,
+	vl_bpix:	LCD_BPP,
+	vl_lbw:		0,
+	vl_splt:	1,
+	vl_clor:	1,
+	vl_tft:		1,
+	vl_hpw:		32,
+	vl_blw:		144,
+	vl_elw:		32,
+	vl_vpw:		2,
+	vl_bfw:		13,
+	vl_efw:		30,
+};
+#endif /* CONFIG_VOIPAC_LCD */
 
 /*----------------------------------------------------------------------*/
 #ifdef CONFIG_HITACHI_SX14
@@ -147,6 +180,40 @@ vidinfo_t panel_info = {
 #endif /* CONFIG_HITACHI_SX14 */
 
 /*----------------------------------------------------------------------*/
+#ifdef CONFIG_LMS283GF05
+
+# define LCD_BPP	LCD_COLOR8
+//# define LCD_INVERT_COLORS
+
+/* you have to set lccr0 and lccr3 (including pcd) */
+# define REG_LCCR0	0x043008f8
+# define REG_LCCR3	0x03b00009
+
+vidinfo_t panel_info = {
+	vl_col:		240,
+	vl_row:		320,
+	vl_width:	240,
+	vl_height:	320,
+	vl_clkp:	CONFIG_SYS_HIGH,
+	vl_oep:		CONFIG_SYS_LOW,
+	vl_hsp:		CONFIG_SYS_LOW,
+	vl_vsp:		CONFIG_SYS_LOW,
+	vl_dp:		CONFIG_SYS_HIGH,
+	vl_bpix:	LCD_BPP,
+	vl_lbw:		0,
+	vl_splt:	1,
+	vl_clor:	1,
+	vl_tft:		1,
+	vl_hpw:		4,
+	vl_blw:		4,
+	vl_elw:		8,
+	vl_vpw:		4,
+	vl_bfw:		4,
+	vl_efw:		8,
+};
+#endif /* CONFIG_LMS283GF05 */
+
+/*----------------------------------------------------------------------*/
 
 #if LCD_BPP == LCD_COLOR8
 void lcd_setcolreg (ushort regno, ushort red, ushort green, ushort blue);
@@ -292,7 +359,9 @@ static int pxafb_init_mem (void *lcdbase, vidinfo_t *vid)
 
 	return 0;
 }
-
+#ifdef	CONFIG_CPU_MONAHANS
+static inline void pxafb_setup_gpio (vidinfo_t *vid) {}
+#else
 static void pxafb_setup_gpio (vidinfo_t *vid)
 {
 	u_long lccr0;
@@ -349,6 +418,7 @@ static void pxafb_setup_gpio (vidinfo_t *vid)
 		printf("pxafb_setup_gpio: unable to determine bits per pixel\n");
 	}
 }
+#endif
 
 static void pxafb_enable_controller (vidinfo_t *vid)
 {
@@ -363,7 +433,11 @@ static void pxafb_enable_controller (vidinfo_t *vid)
 	FDADR1 = vid->pxa.fdadr1;
 	LCCR0 |= LCCR0_ENB;
 
+#ifdef	CONFIG_CPU_MONAHANS
+	CKENA |= CKENA_1_LCD;
+#else
 	CKEN |= CKEN16_LCD;
+#endif
 
 	debug("FDADR0 = 0x%08x\n", (unsigned int)FDADR0);
 	debug("FDADR1 = 0x%08x\n", (unsigned int)FDADR1);

arch/arm/cpu/pxa/start.S

@@ -34,6 +34,25 @@
 
 .globl _start
 _start: b	reset
+#ifdef CONFIG_PRELOADER
+	ldr	pc, _hang
+	ldr	pc, _hang
+	ldr	pc, _hang
+	ldr	pc, _hang
+	ldr	pc, _hang
+	ldr	pc, _hang
+	ldr	pc, _hang
+
+_hang:
+	.word	do_hang
+	.word	0x12345678
+	.word	0x12345678
+	.word	0x12345678
+	.word	0x12345678
+	.word	0x12345678
+	.word	0x12345678
+	.word	0x12345678	/* now 16*4=64 */
+#else
 	ldr	pc, _undefined_instruction
 	ldr	pc, _software_interrupt
 	ldr	pc, _prefetch_abort
@@ -49,6 +68,7 @@ _data_abort:		.word data_abort
 _not_used:		.word not_used
 _irq:			.word irq
 _fiq:			.word fiq
+#endif	/* CONFIG_PRELOADER */
 
 	.balignl 16,0xdeadbeef
 
@@ -117,8 +137,10 @@ reset:
 relocate:				/* relocate U-Boot to RAM	    */
 	adr	r0, _start		/* r0 <- current position of code   */
 	ldr	r1, _TEXT_BASE		/* test if we run from flash or RAM */
+#ifndef	CONFIG_PRELOADER
 	cmp	r0, r1			/* don't reloc during debug	    */
 	beq	stack_setup
+#endif
 
 	ldr	r2, _armboot_start
 	ldr	r3, _bss_start
@@ -135,28 +157,37 @@ copy_loop:
 	/* Set up the stack						    */
 stack_setup:
 	ldr	r0, _TEXT_BASE		/* upper 128 KiB: relocated uboot   */
-	sub	r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area			    */
+#ifdef CONFIG_PRELOADER
-	sub	r0, r0, #CONFIG_SYS_GBL_DATA_SIZE /* bdinfo			    */
+	sub	sp, r0, #128		/* leave 32 words for abort-stack   */
+#else
+	sub	r0, r0, #CONFIG_SYS_MALLOC_LEN /* malloc area		    */
+	sub	r0, r0, #CONFIG_SYS_GBL_DATA_SIZE /* bdinfo		    */
 #ifdef CONFIG_USE_IRQ
 	sub	r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
 #endif /* CONFIG_USE_IRQ */
 	sub	sp, r0, #12		/* leave 3 words for abort-stack    */
 	bic	sp, sp, #7		/* 8-byte alignment for ABI compliance */
+#endif
 
 clear_bss:
 	ldr	r0, _bss_start		/* find start of bss segment	    */
 	ldr	r1, _bss_end		/* stop here			    */
 	mov	r2, #0x00000000		/* clear			    */
 
+#ifndef CONFIG_PRELOADER
 clbss_l:str	r2, [r0]		/* clear loop...		    */
 	add	r0, r0, #4
 	cmp	r0, r1
 	ble	clbss_l
+#endif
 
 	ldr	pc, _start_armboot
 
+#ifdef CONFIG_ONENAND_IPL
+_start_armboot: .word start_oneboot
+#else
 _start_armboot: .word start_armboot
-
+#endif
 
 /****************************************************************************/
 /*									    */
@@ -296,7 +327,7 @@ setspeed_done:
 */
 	mov	pc, lr
 
-
+#ifndef CONFIG_PRELOADER
 /****************************************************************************/
 /*									    */
 /* Interrupt handling							    */
@@ -394,6 +425,7 @@ setspeed_done:
 	.macro get_fiq_stack			@ setup FIQ stack
 	ldr	sp, FIQ_STACK_START
 	.endm
+#endif	/* CONFIG_PRELOADER */
 
 
 /****************************************************************************/
@@ -402,6 +434,12 @@ setspeed_done:
 /*									    */
 /****************************************************************************/
 
+#ifdef CONFIG_PRELOADER
+	.align	5
+do_hang:
+	ldr	sp, _TEXT_BASE			/* use 32 words abort stack */
+	bl	hang				/* hang and never return */
+#else	/* !CONFIG_PRELOADER */
 	.align	5
 undefined_instruction:
 	get_bad_stack
@@ -461,7 +499,7 @@ fiq:
 	get_bad_stack
 	bad_save_user_regs
 	bl	do_fiq
-
+#endif	/* CONFIG_PRELOADER */
 #endif /* CONFIG_USE_IRQ */
 
 /****************************************************************************/

arch/arm/include/asm/arch-pxa/macro.h

@@ -0,0 +1,324 @@
+/*
+ * arch/arm/include/asm/arch-pxa/macro.h
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __ASM_ARCH_PXA_MACRO_H__
+#define __ASM_ARCH_PXA_MACRO_H__
+#ifdef __ASSEMBLY__
+
+#include <asm/macro.h>
+#include <asm/arch/pxa-regs.h>
+
+/*
+ * This macro performs a 32bit write to a memory location and makes sure the
+ * write operation really happened by performing a read back.
+ *
+ * Clobbered regs: r4, r5
+ */
+.macro	write32rb addr, data
+	ldr	r4, =\addr
+	ldr	r5, =\data
+	str	r5, [r4]
+	ldr	r5, [r4]
+.endm
+
+/*
+ * This macro waits according to OSCR incrementation
+ *
+ * Clobbered regs: r4, r5, r6
+ */
+.macro	pxa_wait_ticks ticks
+	ldr	r4, =OSCR
+	mov	r5, #0
+	str	r5, [r4]
+	ldr	r5, =\ticks
+1:
+	ldr	r6, [r4]
+	cmp	r5, r6
+	bgt	1b
+.endm
+
+/*
+ * This macro sets up the GPIO pins of the PXA2xx/PXA3xx CPU
+ *
+ * Clobbered regs: r4, r5
+ */
+.macro	pxa_gpio_setup
+	write32	GPSR0, CONFIG_SYS_GPSR0_VAL
+	write32	GPSR1, CONFIG_SYS_GPSR1_VAL
+	write32	GPSR2, CONFIG_SYS_GPSR2_VAL
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+	write32	GPSR3, CONFIG_SYS_GPSR3_VAL
+#endif
+
+	write32	GPCR0, CONFIG_SYS_GPCR0_VAL
+	write32	GPCR1, CONFIG_SYS_GPCR1_VAL
+	write32	GPCR2, CONFIG_SYS_GPCR2_VAL
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+	write32	GPCR3, CONFIG_SYS_GPCR3_VAL
+#endif
+
+	write32	GPDR0, CONFIG_SYS_GPDR0_VAL
+	write32	GPDR1, CONFIG_SYS_GPDR1_VAL
+	write32	GPDR2, CONFIG_SYS_GPDR2_VAL
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+	write32	GPDR3, CONFIG_SYS_GPDR3_VAL
+#endif
+
+	write32	GAFR0_L, CONFIG_SYS_GAFR0_L_VAL
+	write32	GAFR0_U, CONFIG_SYS_GAFR0_U_VAL
+	write32	GAFR1_L, CONFIG_SYS_GAFR1_L_VAL
+	write32	GAFR1_U, CONFIG_SYS_GAFR1_U_VAL
+	write32	GAFR2_L, CONFIG_SYS_GAFR2_L_VAL
+	write32	GAFR2_U, CONFIG_SYS_GAFR2_U_VAL
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+	write32	GAFR3_L, CONFIG_SYS_GAFR3_L_VAL
+	write32	GAFR3_U, CONFIG_SYS_GAFR3_U_VAL
+#endif
+
+	write32	PSSR, CONFIG_SYS_PSSR_VAL
+.endm
+
+/*
+ * This macro sets up the Memory controller of the PXA2xx CPU
+ *
+ * Clobbered regs: r3, r4, r5
+ */
+.macro	pxa_mem_setup
+	/* This comes handy when setting MDREFR */
+	ldr	r3, =MEMC_BASE
+
+	/*
+	 * 1) Initialize Asynchronous static memory controller
+	 */
+
+	/* MSC0: nCS(0,1) */
+	write32rb	(MEMC_BASE + MSC0_OFFSET), CONFIG_SYS_MSC0_VAL
+	/* MSC1: nCS(2,3) */
+	write32rb	(MEMC_BASE + MSC1_OFFSET), CONFIG_SYS_MSC1_VAL
+	/* MSC2: nCS(4,5) */
+	write32rb	(MEMC_BASE + MSC2_OFFSET), CONFIG_SYS_MSC2_VAL
+
+	/*
+	 * 2) Initialize Card Interface
+	 */
+
+	/* MECR: Memory Expansion Card Register */
+	write32rb	(MEMC_BASE + MECR_OFFSET), CONFIG_SYS_MECR_VAL
+	/* MCMEM0: Card Interface slot 0 timing */
+	write32rb	(MEMC_BASE + MCMEM0_OFFSET), CONFIG_SYS_MCMEM0_VAL
+	/* MCMEM1: Card Interface slot 1 timing */
+	write32rb	(MEMC_BASE + MCMEM1_OFFSET), CONFIG_SYS_MCMEM1_VAL
+	/* MCATT0: Card Interface Attribute Space Timing, slot 0 */
+	write32rb	(MEMC_BASE + MCATT0_OFFSET), CONFIG_SYS_MCATT0_VAL
+	/* MCATT1: Card Interface Attribute Space Timing, slot 1 */
+	write32rb	(MEMC_BASE + MCATT1_OFFSET), CONFIG_SYS_MCATT1_VAL
+	/* MCIO0: Card Interface I/O Space Timing, slot 0 */
+	write32rb	(MEMC_BASE + MCIO0_OFFSET), CONFIG_SYS_MCIO0_VAL
+	/* MCIO1: Card Interface I/O Space Timing, slot 1 */
+	write32rb	(MEMC_BASE + MCIO1_OFFSET), CONFIG_SYS_MCIO1_VAL
+
+	/*
+	 * 3) Configure Fly-By DMA register
+	 */
+
+	write32rb	(MEMC_BASE + FLYCNFG_OFFSET), CONFIG_SYS_FLYCNFG_VAL
+
+	/*
+	 * 4) Initialize Timing for Sync Memory (SDCLK0)
+	 */
+
+	/*
+	 * Before accessing MDREFR we need a valid DRI field, so we set
+	 * this to power on defaults + DRI field.
+	 */
+	ldr	r5, [r3, #MDREFR_OFFSET]
+	bic	r5, r5, #0x0ff
+	bic	r5, r5, #0xf00	/* MDREFR user config with zeroed DRI */
+
+	ldr	r4, =CONFIG_SYS_MDREFR_VAL
+	mov	r6, r4
+	lsl	r4, #20
+	lsr	r4, #20		/* Get a valid DRI field */
+
+	orr	r5, r5, r4	/* MDREFR user config with correct DRI */
+
+	orr	r5, #MDREFR_K0RUN
+	orr	r5, #MDREFR_SLFRSH
+	bic	r5, #MDREFR_APD
+	bic	r5, #MDREFR_E1PIN
+
+	str	r5, [r3, #MDREFR_OFFSET]
+	ldr	r4, [r3, #MDREFR_OFFSET]
+
+	/*
+	 * 5) Initialize Synchronous Static Memory (Flash/Peripherals)
+	 */
+
+	/* Initialize SXCNFG register. Assert the enable bits.
+	 *
+	 * Write SXMRS to cause an MRS command to all enabled banks of
+	 * synchronous static memory. Note that SXLCR need not be written
+	 * at this time.
+	 */
+	write32rb	(MEMC_BASE + SXCNFG_OFFSET), CONFIG_SYS_SXCNFG_VAL
+
+	/*
+	 * 6) Initialize SDRAM
+	 */
+
+	bic	r6, #MDREFR_SLFRSH
+	str	r6, [r3, #MDREFR_OFFSET]
+	ldr	r4, [r3, #MDREFR_OFFSET]
+
+	orr	r6, #MDREFR_E1PIN
+	str	r6, [r3, #MDREFR_OFFSET]
+	ldr	r4, [r3, #MDREFR_OFFSET]
+
+	/*
+	 * 7) Write MDCNFG with MDCNFG:DEx deasserted (set to 0), to configure
+	 *    but not enable each SDRAM partition pair.
+	 */
+
+	/* Fetch platform value of MDCNFG */
+	ldr	r4, =CONFIG_SYS_MDCNFG_VAL
+	/* Disable all sdram banks */
+	bic	r4, r4, #(MDCNFG_DE0|MDCNFG_DE1)
+	bic	r4, r4, #(MDCNFG_DE2|MDCNFG_DE3)
+	/* Write initial value of MDCNFG, w/o enabling sdram banks */
+	str	r4, [r3, #MDCNFG_OFFSET]
+	ldr	r4, [r3, #MDCNFG_OFFSET]
+
+	/* Wait for the clock to the SDRAMs to stabilize, 100..200 usec. */
+	pxa_wait_ticks	0x300
+
+	/*
+	 * 8) Trigger a number (usually 8) refresh cycles by attempting
+	 *    non-burst read or write accesses to disabled SDRAM, as commonly
+	 *    specified in the power up sequence documented in SDRAM data
+	 *    sheets. The address(es) used for this purpose must not be
+	 *    cacheable.
+	 */
+
+	ldr	r4, =CONFIG_SYS_DRAM_BASE
+.rept 9
+	str	r5, [r4]
+.endr
+
+	/*
+	 * 9) Write MDCNFG with enable bits asserted (MDCNFG:DEx set to 1).
+	 */
+
+	ldr	r5, =CONFIG_SYS_MDCNFG_VAL
+	ldr	r4, =(MDCNFG_DE0 | MDCNFG_DE1 | MDCNFG_DE2 | MDCNFG_DE3)
+	and	r5, r5, r4
+	ldr     r4, [r3, #MDCNFG_OFFSET]
+	orr	r4, r4, r5
+	str     r4, [r3, #MDCNFG_OFFSET]
+	ldr     r4, [r3, #MDCNFG_OFFSET]
+
+	/*
+	 * 10) Write MDMRS.
+	 */
+
+	ldr     r4, =CONFIG_SYS_MDMRS_VAL
+	str     r4, [r3, #MDMRS_OFFSET]
+	ldr     r4, [r3, #MDMRS_OFFSET]
+
+	/*
+	 * 11) Enable APD
+	 */
+
+	ldr	r4, [r3, #MDREFR_OFFSET]
+	and	r6, r6, #MDREFR_APD
+	orr	r4, r4, r6
+	str	r4, [r3, #MDREFR_OFFSET]
+	ldr	r4, [r3, #MDREFR_OFFSET]
+.endm
+
+/*
+ * This macro tests if the CPU woke up from sleep and eventually resumes
+ *
+ * Clobbered regs: r4, r5
+ */
+.macro	pxa_wakeup
+	ldr	r4, =RCSR
+	ldr	r5, [r4]
+	and	r5, r5, #(RCSR_GPR | RCSR_SMR | RCSR_WDR | RCSR_HWR)
+	str	r5, [r4]
+	teq	r5, #RCSR_SMR
+
+	bne	pxa_wakeup_exit
+
+	ldr	r4, =PSSR
+	mov	r5, #PSSR_PH
+	str	r5, [r4]
+
+	ldr	r4, =PSPR
+	ldr	pc, [r4]
+pxa_wakeup_exit:
+.endm
+
+/*
+ * This macro disables all interupts on PXA2xx/PXA3xx CPU
+ *
+ * Clobbered regs: r4, r5
+ */
+.macro	pxa_intr_setup
+	write32	ICLR, 0
+	write32	ICMR, 0
+#if defined(CONFIG_PXA27X) || defined(CONFIG_CPU_MONAHANS)
+	write32	ICLR2, 0
+	write32	ICMR2, 0
+#endif
+.endm
+
+/*
+ * This macro configures clock on PXA2xx/PXA3xx CPU
+ *
+ * Clobbered regs: r4, r5
+ */
+.macro	pxa_clock_setup
+	/* Disable the peripheral clocks, and set the core clock frequency */
+
+	/* Turn Off ALL on-chip peripheral clocks for re-configuration */
+	write32	CKEN, CONFIG_SYS_CKEN
+
+	/* Write CCCR */
+	write32	CCCR, CONFIG_SYS_CCCR
+
+#ifdef CONFIG_RTC
+	/* enable the 32Khz oscillator for RTC and PowerManager */
+	write32	OSCC, #OSCC_OON
+	ldr	r4, =OSCC
+
+	/* Spin here until OSCC.OOK get set, meaning the PLL has settled. */
+2:
+	ldr	r5, [r4]
+	ands	r5, r5, #1
+	beq	2b
+#endif
+.endm
+
+#endif /* __ASSEMBLY__ */
+#endif /* __ASM_ARCH_PXA_MACRO_H__ */

arch/arm/include/asm/arch-pxa/pxa-regs.h

@@ -1132,10 +1132,18 @@ typedef void		(*ExcpHndlr) (void) ;
 #define PWM_PWDUTY0	__REG(0x40B00004)  /* PWM 0 Duty Cycle Register */
 #define PWM_PERVAL0	__REG(0x40B00008)  /* PWM 0 Period Control Register */
 
-#define PWM_CTRL1	__REG(0x40C00000)  /* PWM 1Control Register */
+#define PWM_CTRL1	__REG(0x40C00000)  /* PWM 1 Control Register */
 #define PWM_PWDUTY1	__REG(0x40C00004)  /* PWM 1 Duty Cycle Register */
 #define PWM_PERVAL1	__REG(0x40C00008)  /* PWM 1 Period Control Register */
 
+#define PWM_CTRL2	__REG(0x40B00010)  /* PWM 2 Control Register */
+#define PWM_PWDUTY2	__REG(0x40B00014)  /* PWM 2 Duty Cycle Register */
+#define PWM_PERVAL2	__REG(0x40B00018)  /* PWM 2 Period Control Register */
+
+#define PWM_CTRL3	__REG(0x40C00010)  /* PWM 3 Control Register */
+#define PWM_PWDUTY3	__REG(0x40C00014)  /* PWM 3 Duty Cycle Register */
+#define PWM_PERVAL3	__REG(0x40C00018)  /* PWM 3 Period Control Register */
+
 /*
  * Interrupt Controller
  */

board/colibri_pxa270/Makefile

@@ -0,0 +1,45 @@
+#
+# Toradex Colibri PXA270 Support
+#
+# Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= colibri_pxa270.o
+SOBJS	:= lowlevel_init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/colibri_pxa270/colibri_pxa270.c

@@ -0,0 +1,118 @@
+/*
+ * Toradex Colibri PXA270 Support
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+extern struct serial_device serial_ffuart_device;
+extern struct serial_device serial_btuart_device;
+extern struct serial_device serial_stuart_device;
+
+struct serial_device *default_serial_console (void)
+{
+	return &serial_ffuart_device;
+}
+
+int board_init (void)
+{
+	/* memory and cpu-speed are setup before relocation */
+	/* so we do _nothing_ here */
+
+	/* arch number of vpac270 */
+	gd->bd->bi_arch_number = MACH_TYPE_COLIBRI;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0xa0000100;
+
+	return 0;
+}
+
+int dram_init (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+	return 0;
+}
+
+#ifdef	CONFIG_CMD_USB
+int usb_board_init(void)
+{
+	UHCHR = (UHCHR | UHCHR_PCPL | UHCHR_PSPL) &
+		~(UHCHR_SSEP0 | UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSE);
+
+	UHCHR |= UHCHR_FSBIR;
+
+	while (UHCHR & UHCHR_FSBIR);
+
+	UHCHR &= ~UHCHR_SSE;
+	UHCHIE = (UHCHIE_UPRIE | UHCHIE_RWIE);
+
+	/* Clear any OTG Pin Hold */
+	if (PSSR & PSSR_OTGPH)
+		PSSR |= PSSR_OTGPH;
+
+	UHCRHDA &= ~(0x200);
+	UHCRHDA |= 0x100;
+
+	/* Set port power control mask bits, only 3 ports. */
+	UHCRHDB |= (0x7<<17);
+
+	/* enable port 2 */
+	UP2OCR |= UP2OCR_HXOE | UP2OCR_HXS | UP2OCR_DMPDE | UP2OCR_DPPDE;
+
+	return 0;
+}
+
+void usb_board_init_fail(void)
+{
+	return;
+}
+
+void usb_board_stop(void)
+{
+	UHCHR |= UHCHR_FHR;
+	udelay(11);
+	UHCHR &= ~UHCHR_FHR;
+
+	UHCCOMS |= 1;
+	udelay(10);
+
+	CKEN &= ~CKEN10_USBHOST;
+
+	return;
+}
+#endif
+
+#ifdef CONFIG_DRIVER_DM9000
+int board_eth_init(bd_t *bis)
+{
+	return dm9000_initialize(bis);
+}
+#endif

board/colibri_pxa270/config.mk

@@ -0,0 +1 @@
+TEXT_BASE = 0xa1000000

board/colibri_pxa270/lowlevel_init.S

@@ -0,0 +1,36 @@
+/*
+ * Toradex Colibri PXA270 Lowlevel Hardware Initialization
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+	pxa_gpio_setup
+	pxa_wait_ticks	0x8000
+	pxa_mem_setup
+	pxa_wakeup
+	pxa_intr_setup
+	pxa_clock_setup
+
+	mov	pc, lr

board/vpac270/Makefile

@@ -0,0 +1,48 @@
+
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= vpac270.o
+SOBJS	:= lowlevel_init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/vpac270/config.mk

@@ -0,0 +1 @@
+TEXT_BASE = 0xa1000000

board/vpac270/lowlevel_init.S

@@ -0,0 +1,40 @@
+/*
+ * Voipac PXA270 Lowlevel Hardware Initialization
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+	pxa_gpio_setup
+	pxa_wait_ticks	0x8000
+	pxa_mem_setup
+	pxa_wakeup
+	pxa_intr_setup
+	pxa_clock_setup
+
+	mov	pc, lr

board/vpac270/u-boot.lds

@@ -0,0 +1,55 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+	  cpu/pxa/start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}

board/vpac270/vpac270.c

@@ -0,0 +1,127 @@
+/*
+ * (C) Copyright 2004
+ * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net
+ *
+ * (C) Copyright 2002
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+extern struct serial_device serial_ffuart_device;
+extern struct serial_device serial_btuart_device;
+extern struct serial_device serial_stuart_device;
+
+struct serial_device *default_serial_console (void)
+{
+	return &serial_ffuart_device;
+}
+
+int board_init (void)
+{
+	/* memory and cpu-speed are setup before relocation */
+	/* so we do _nothing_ here */
+
+	/* arch number of vpac270 */
+	gd->bd->bi_arch_number = MACH_TYPE_VPAC270;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0xa0000100;
+
+	return 0;
+}
+
+int dram_init (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+
+	return 0;
+}
+
+int usb_board_init(void)
+{
+	UHCHR = (UHCHR | UHCHR_PCPL | UHCHR_PSPL) &
+		~(UHCHR_SSEP0 | UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSE);
+
+	UHCHR |= UHCHR_FSBIR;
+
+	while (UHCHR & UHCHR_FSBIR);
+
+	UHCHR &= ~UHCHR_SSE;
+	UHCHIE = (UHCHIE_UPRIE | UHCHIE_RWIE);
+
+	/* Clear any OTG Pin Hold */
+	if (PSSR & PSSR_OTGPH)
+		PSSR |= PSSR_OTGPH;
+
+	UHCRHDA &= ~(0x200);
+	UHCRHDA |= 0x100;
+
+	/* Set port power control mask bits, only 3 ports. */
+	UHCRHDB |= (0x7<<17);
+
+	/* enable port 2 */
+	UP2OCR |= UP2OCR_HXOE | UP2OCR_HXS | UP2OCR_DMPDE | UP2OCR_DPPDE;
+
+	return 0;
+}
+
+void usb_board_init_fail(void)
+{
+	return;
+}
+
+void usb_board_stop(void)
+{
+	UHCHR |= UHCHR_FHR;
+	udelay(11);
+	UHCHR &= ~UHCHR_FHR;
+
+	UHCCOMS |= 1;
+	udelay(10);
+
+	CKEN &= ~CKEN10_USBHOST;
+
+	return;
+}
+
+#ifdef CONFIG_DRIVER_DM9000
+int board_eth_init(bd_t *bis)
+{
+	return dm9000_initialize(bis);
+}
+#endif

board/zipitz2/Makefile

@@ -0,0 +1,54 @@
+
+#
+# Copyright (C) 2009
+# Marek Vasut <marek.vasut@gmail.com>
+#
+# Heavily based on pxa255_idp platform
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= zipitz2.o
+SOBJS	:= lowlevel_init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/zipitz2/config.mk

@@ -0,0 +1 @@
+TEXT_BASE = 0xa1000000

board/zipitz2/lowlevel_init.S

@@ -0,0 +1,40 @@
+/*
+ * Aeronix Zipit Z2 Lowlevel Hardware Initialization
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+	pxa_gpio_setup
+	pxa_wait_ticks	0x8000
+	pxa_mem_setup
+	pxa_wakeup
+	pxa_intr_setup
+	pxa_clock_setup
+
+	mov	pc, lr

board/zipitz2/u-boot.lds

@@ -0,0 +1,56 @@
+/*
+ * (C) Copyright 2000-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+	  cpu/pxa/start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	. = .;
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
+	_end = .;
+}

board/zipitz2/zipitz2.c

@@ -0,0 +1,213 @@
+/*
+ * Copyright (C) 2009
+ * Marek Vasut <marek.vasut@gmail.com>
+ *
+ * Heavily based on pxa255_idp platform
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <serial.h>
+#include <asm/arch/hardware.h>
+#include <spi.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef	CONFIG_CMD_SPI
+void lcd_start(void);
+#else
+inline void lcd_start(void) {};
+#endif
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	/* memory and cpu-speed are setup before relocation */
+	/* so we do _nothing_ here */
+
+	/* arch number of Lubbock-Board */
+	gd->bd->bi_arch_number = MACH_TYPE_ZIPIT2;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0xa0000100;
+
+	/* Enable LCD */
+	lcd_start();
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	setenv("stdout", "serial");
+	setenv("stderr", "serial");
+	return 0;
+}
+
+struct serial_device *default_serial_console (void)
+{
+	return &serial_stuart_device;
+}
+
+int dram_init (void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+	return 0;
+}
+
+#ifdef	CONFIG_CMD_SPI
+
+struct {
+	unsigned char	reg;
+	unsigned short	data;
+	unsigned char	mdelay;
+} lcd_data[] = {
+	{ 0x07,	0x0000,	0 },
+	{ 0x13,	0x0000,	10 },
+	{ 0x11,	0x3004,	0 },
+	{ 0x14,	0x200F,	0 },
+	{ 0x10,	0x1a20,	0 },
+	{ 0x13,	0x0040,	50 },
+	{ 0x13,	0x0060,	0 },
+	{ 0x13,	0x0070,	200 },
+	{ 0x01,	0x0127,	0 },
+	{ 0x02,	0x0700,	0 },
+	{ 0x03,	0x1030,	0 },
+	{ 0x08,	0x0208,	0 },
+	{ 0x0B,	0x0620,	0 },
+	{ 0x0C,	0x0110,	0 },
+	{ 0x30,	0x0120,	0 },
+	{ 0x31,	0x0127,	0 },
+	{ 0x32,	0x0000,	0 },
+	{ 0x33,	0x0503,	0 },
+	{ 0x34,	0x0727,	0 },
+	{ 0x35,	0x0124,	0 },
+	{ 0x36,	0x0706,	0 },
+	{ 0x37,	0x0701,	0 },
+	{ 0x38,	0x0F00,	0 },
+	{ 0x39,	0x0F00,	0 },
+	{ 0x40,	0x0000,	0 },
+	{ 0x41,	0x0000,	0 },
+	{ 0x42,	0x013f,	0 },
+	{ 0x43,	0x0000,	0 },
+	{ 0x44,	0x013f,	0 },
+	{ 0x45,	0x0000,	0 },
+	{ 0x46,	0xef00,	0 },
+	{ 0x47,	0x013f,	0 },
+	{ 0x48,	0x0000,	0 },
+	{ 0x07,	0x0015,	30 },
+	{ 0x07,	0x0017,	0 },
+	{ 0x20,	0x0000,	0 },
+	{ 0x21,	0x0000,	0 },
+	{ 0x22,	0x0000,	0 },
+};
+
+void zipitz2_spi_sda(int set)
+{
+	/* GPIO 13 */
+	if (set)
+		GPSR0 = (1 << 13);
+	else
+		GPCR0 = (1 << 13);
+}
+
+void zipitz2_spi_scl(int set)
+{
+	/* GPIO 22 */
+	if (set)
+		GPCR0 = (1 << 22);
+	else
+		GPSR0 = (1 << 22);
+}
+
+unsigned char zipitz2_spi_read(void)
+{
+	/* GPIO 40 */
+	return !!(GPLR1 & (1 << 8));
+}
+
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+	/* Always valid */
+	return 1;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+	/* GPIO 88 low */
+	GPCR2 = (1 << 24);
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+	/* GPIO 88 high */
+	GPSR2 = (1 << 24);
+
+}
+
+void lcd_start(void)
+{
+	int i;
+	unsigned char reg[3] = { 0x74, 0x00, 0 };
+	unsigned char data[3] = { 0x76, 0, 0 };
+	unsigned char dummy[3] = { 0, 0, 0 };
+
+	/* PWM2 AF */
+	GAFR0_L |= 0x00800000;
+	/* Enable clock to all PWM */
+	CKEN |= 0x3;
+	/* Configure PWM2 */
+	PWM_CTRL2 = 0x4f;
+	PWM_PWDUTY2 = 0x2ff;
+	PWM_PERVAL2 = 792;
+
+	/* Toggle the reset pin to reset the LCD */
+	GPSR0 = (1 << 19);
+	udelay(100000);
+	GPCR0 = (1 << 19);
+	udelay(20000);
+	GPSR0 = (1 << 19);
+	udelay(20000);
+
+	/* Program the LCD init sequence */
+	for (i = 0; i < sizeof(lcd_data) / sizeof(lcd_data[0]); i++) {
+		reg[0] = 0x74;
+		reg[1] = 0x0;
+		reg[2] = lcd_data[i].reg;
+		spi_xfer(NULL, 24, reg, dummy, SPI_XFER_BEGIN | SPI_XFER_END);
+
+		data[0] = 0x76;
+		data[1] = lcd_data[i].data >> 8;
+		data[2] = lcd_data[i].data & 0xff;
+		spi_xfer(NULL, 24, data, dummy, SPI_XFER_BEGIN | SPI_XFER_END);
+
+		if (lcd_data[i].mdelay)
+			udelay(lcd_data[i].mdelay * 1000);
+	}
+
+	GPSR0 = (1 << 11);
+}
+#endif

boards.cfg

@@ -52,6 +52,7 @@ actux3		arm	ixp
 actux4		arm	ixp
 ixdp425		arm	ixp
 cerf250		arm	pxa
+colibri_pxa270	arm	pxa
 cradle		arm	pxa
 csb226		arm	pxa
 delta		arm	pxa
@@ -61,6 +62,7 @@ lubbock		arm	pxa
 pleb2		arm	pxa
 xaeniax		arm	pxa
 xm250		arm	pxa
+zipitz2		arm	pxa
 B2		arm	s3c44b0		-		dave
 assabet		arm	sa1100
 dnp1110		arm	sa1100

common/lcd.c

@@ -41,7 +41,7 @@
 #include <lcd.h>
 #include <watchdog.h>
 
-#if defined(CONFIG_PXA250)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
 #include <asm/byteorder.h>
 #endif
 
@@ -503,7 +503,7 @@ void bitmap_plot (int x, int y)
 	uchar *bmap;
 	uchar *fb;
 	ushort *fb16;
-#if defined(CONFIG_PXA250)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
 	struct pxafb_info *fbi = &panel_info.pxa;
 #elif defined(CONFIG_MPC823)
 	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
@@ -519,7 +519,7 @@ void bitmap_plot (int x, int y)
 
 	if (NBITS(panel_info.vl_bpix) < 12) {
 		/* Leave room for default color map */
-#if defined(CONFIG_PXA250)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
 		cmap = (ushort *)fbi->palette;
 #elif defined(CONFIG_MPC823)
 		cmap = (ushort *)&(cp->lcd_cmap[BMP_LOGO_OFFSET*sizeof(ushort)]);
@@ -615,7 +615,7 @@ int lcd_display_bitmap(ulong bmp_image, int x, int y)
 	unsigned long pwidth = panel_info.vl_col;
 	unsigned colors, bpix, bmp_bpix;
 	unsigned long compression;
-#if defined(CONFIG_PXA250)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
 	struct pxafb_info *fbi = &panel_info.pxa;
 #elif defined(CONFIG_MPC823)
 	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
@@ -656,7 +656,7 @@ int lcd_display_bitmap(ulong bmp_image, int x, int y)
 #if !defined(CONFIG_MCC200)
 	/* MCC200 LCD doesn't need CMAP, supports 1bpp b&w only */
 	if (bmp_bpix == 8) {
-#if defined(CONFIG_PXA250)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
 		cmap = (ushort *)fbi->palette;
 #elif defined(CONFIG_MPC823)
 		cmap = (ushort *)&(cp->lcd_cmap[255*sizeof(ushort)]);
@@ -745,7 +745,7 @@ int lcd_display_bitmap(ulong bmp_image, int x, int y)
 			WATCHDOG_RESET();
 			for (j = 0; j < width; j++) {
 				if (bpix != 16) {
-#if defined(CONFIG_PXA250) || defined(CONFIG_ATMEL_LCD)
+#if defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS || defined(CONFIG_ATMEL_LCD)
 					*(fb++) = *(bmap++);
 #elif defined(CONFIG_MPC823) || defined(CONFIG_MCC200)
 					*(fb++) = 255 - *(bmap++);

include/configs/colibri_pxa270.h

@@ -0,0 +1,278 @@
+/*
+ * Toradex Colibri PXA270 configuration file
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Board Configuration Options
+ */
+#define	CONFIG_PXA27X		1	/* Marvell PXA270 CPU */
+#define	CONFIG_VPAC270		1	/* Toradex Colibri PXA270 board */
+
+#undef	BOARD_LATE_INIT
+#undef	CONFIG_SKIP_RELOCATE_UBOOT
+#undef	CONFIG_USE_IRQ
+#undef	CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Environment settings
+ */
+#define	CONFIG_ENV_SIZE			0x4000
+#define	CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)
+#define	CONFIG_SYS_GBL_DATA_SIZE	128
+
+#define	CONFIG_ENV_OVERWRITE		/* override default environment */
+
+#define	CONFIG_BOOTCOMMAND						\
+	"if mmc init && fatload mmc 0 0xa0000000 uImage; then "		\
+		"bootm 0xa0000000; "					\
+	"fi; "								\
+	"if usb reset && fatload usb 0 0xa0000000 uImage; then "	\
+		"bootm 0xa0000000; "					\
+	"fi; "								\
+	"bootm 0x80000;"
+#define	CONFIG_BOOTARGS			"console=tty0 console=ttyS0,115200"
+#define	CONFIG_TIMESTAMP
+#define	CONFIG_BOOTDELAY		2	/* Autoboot delay */
+#define	CONFIG_CMDLINE_TAG
+#define	CONFIG_SETUP_MEMORY_TAGS
+
+#define	CONFIG_LZMA			/* LZMA compression support */
+
+/*
+ * Serial Console Configuration
+ */
+#define	CONFIG_PXA_SERIAL
+#define	CONFIG_FFUART			1
+#define	CONFIG_BAUDRATE			115200
+#define	CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+
+#define	CONFIG_CMD_NET
+#define	CONFIG_CMD_ENV
+#undef	CONFIG_CMD_IMLS
+#define	CONFIG_CMD_MMC
+#define	CONFIG_CMD_USB
+#define	CONFIG_CMD_FLASH
+
+/*
+ * Networking Configuration
+ *  chip on the Voipac PXA270 board
+ */
+#ifdef	CONFIG_CMD_NET
+#define	CONFIG_CMD_PING
+#define	CONFIG_CMD_DHCP
+
+#define	CONFIG_NET_MULTI		1
+#define	CONFIG_DRIVER_DM9000		1
+#define CONFIG_DM9000_BASE		0x08000000
+#define DM9000_IO			(CONFIG_DM9000_BASE)
+#define DM9000_DATA			(CONFIG_DM9000_BASE + 4)
+#define	CONFIG_NET_RETRY_COUNT		10
+
+#define	CONFIG_BOOTP_BOOTFILESIZE
+#define	CONFIG_BOOTP_BOOTPATH
+#define	CONFIG_BOOTP_GATEWAY
+#define	CONFIG_BOOTP_HOSTNAME
+#endif
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef	CONFIG_CMD_MMC
+#define	CONFIG_MMC
+#define	CONFIG_PXA_MMC
+#define	CONFIG_SYS_MMC_BASE		0xF0000000
+#define	CONFIG_CMD_FAT
+#define	CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef	CONFIG_CMD_KGDB
+#define	CONFIG_KGDB_BAUDRATE		230400		/* speed to run kgdb serial port */
+#define	CONFIG_KGDB_SER_INDEX		2		/* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define	CONFIG_SYS_HUSH_PARSER		1
+#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+#define	CONFIG_SYS_LONGHELP				/* undef to save memory	*/
+#ifdef	CONFIG_SYS_HUSH_PARSER
+#define	CONFIG_SYS_PROMPT		"$ "		/* Monitor Command Prompt */
+#else
+#define	CONFIG_SYS_PROMPT		"=> "		/* Monitor Command Prompt */
+#endif
+#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size */
+#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
+#define	CONFIG_SYS_MAXARGS		16		/* max number of command args */
+#define	CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define	CONFIG_SYS_DEVICE_NULLDEV	1
+
+/*
+ * Clock Configuration
+ */
+#undef	CONFIG_SYS_CLKS_IN_HZ
+#define	CONFIG_SYS_HZ			3250000		/* Timer @ 3250000 Hz */
+#define CONFIG_SYS_CPUSPEED		0x290		/* 520 MHz */
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define	CONFIG_STACKSIZE		(128*1024)	/* regular stack */
+#ifdef	CONFIG_USE_IRQ
+#define	CONFIG_STACKSIZE_IRQ		(4*1024)	/* IRQ stack */
+#define	CONFIG_STACKSIZE_FIQ		(4*1024)	/* FIQ stack */
+#endif
+
+/*
+ * DRAM Map
+ */
+#define	CONFIG_NR_DRAM_BANKS		1		/* We have 1 bank of DRAM */
+#define	PHYS_SDRAM_1			0xa0000000	/* SDRAM Bank #1 */
+#define	PHYS_SDRAM_1_SIZE		0x04000000	/* 64 MB */
+
+#define	CONFIG_SYS_DRAM_BASE		0xa0000000	/* CS0 */
+#define	CONFIG_SYS_DRAM_SIZE		0x04000000	/* 64 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM */
+
+#define	CONFIG_SYS_LOAD_ADDR		(0xa1000000)
+
+/*
+ * NOR FLASH
+ */
+#ifdef	CONFIG_CMD_FLASH
+#define	PHYS_FLASH_1			0x00000000	/* Flash Bank #1 */
+#define	CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
+
+#define	CONFIG_SYS_FLASH_CFI
+#define	CONFIG_FLASH_CFI_DRIVER		1
+
+#define	CONFIG_SYS_MAX_FLASH_SECT	(4 + 255)
+#define	CONFIG_SYS_MAX_FLASH_BANKS	1
+
+#define	CONFIG_SYS_FLASH_ERASE_TOUT	(25*CONFIG_SYS_HZ)
+#define	CONFIG_SYS_FLASH_WRITE_TOUT	(25*CONFIG_SYS_HZ)
+
+#define	CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
+#define	CONFIG_SYS_FLASH_PROTECTION		1
+
+#define CONFIG_ENV_IS_IN_FLASH		1
+
+#else	/* No flash */
+#define	CONFIG_SYS_NO_FLASH
+#define	CONFIG_SYS_ENV_IS_NOWHERE
+#endif
+
+#define	CONFIG_SYS_MONITOR_BASE		0x000000
+#define	CONFIG_SYS_MONITOR_LEN		0x40000
+
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE	0x40000
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+
+/*
+ * GPIO settings
+ */
+#define	CONFIG_SYS_GPSR0_VAL	0x00000000
+#define	CONFIG_SYS_GPSR1_VAL	0x00020000
+#define	CONFIG_SYS_GPSR2_VAL	0x0002C000
+#define	CONFIG_SYS_GPSR3_VAL	0x00000000
+
+#define	CONFIG_SYS_GPCR0_VAL	0x00000000
+#define	CONFIG_SYS_GPCR1_VAL	0x00000000
+#define	CONFIG_SYS_GPCR2_VAL	0x00000000
+#define	CONFIG_SYS_GPCR3_VAL	0x00000000
+
+#define	CONFIG_SYS_GPDR0_VAL	0x08000000
+#define	CONFIG_SYS_GPDR1_VAL	0x0002A981
+#define	CONFIG_SYS_GPDR2_VAL	0x0202FC00
+#define	CONFIG_SYS_GPDR3_VAL	0x00000000
+
+#define	CONFIG_SYS_GAFR0_L_VAL	0x00100000
+#define	CONFIG_SYS_GAFR0_U_VAL	0x00C00010
+#define	CONFIG_SYS_GAFR1_L_VAL	0x999A901A
+#define	CONFIG_SYS_GAFR1_U_VAL	0xAAA00008
+#define	CONFIG_SYS_GAFR2_L_VAL	0xAAAAAAAA
+#define	CONFIG_SYS_GAFR2_U_VAL	0x0109A000
+#define	CONFIG_SYS_GAFR3_L_VAL	0x54000300
+#define	CONFIG_SYS_GAFR3_U_VAL	0x00024001
+
+#define	CONFIG_SYS_PSSR_VAL	0x30
+
+/*
+ * Clock settings
+ */
+#define	CONFIG_SYS_CKEN		0x00500240
+#define	CONFIG_SYS_CCCR		0x02000290
+
+/*
+ * Memory settings
+ */
+#define	CONFIG_SYS_MSC0_VAL	0x000095f2
+#define	CONFIG_SYS_MSC1_VAL	0x00007ff4
+#define	CONFIG_SYS_MSC2_VAL	0x00000000
+#define	CONFIG_SYS_MDCNFG_VAL	0x08000ac9
+#define	CONFIG_SYS_MDREFR_VAL	0x2013e01e
+#define	CONFIG_SYS_MDMRS_VAL	0x00320032
+#define	CONFIG_SYS_FLYCNFG_VAL	0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL	0x40044004
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define	CONFIG_SYS_MECR_VAL	0x00000001
+#define	CONFIG_SYS_MCMEM0_VAL	0x00014307
+#define	CONFIG_SYS_MCMEM1_VAL	0x00014307
+#define	CONFIG_SYS_MCATT0_VAL	0x0001c787
+#define	CONFIG_SYS_MCATT1_VAL	0x0001c787
+#define	CONFIG_SYS_MCIO0_VAL	0x0001430f
+#define	CONFIG_SYS_MCIO1_VAL	0x0001430f
+
+/*
+ * USB
+ */
+#ifdef CONFIG_CMD_USB
+#define	CONFIG_USB_OHCI_NEW
+#define	CONFIG_SYS_USB_OHCI_CPU_INIT
+#define	CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define	CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
+#define	CONFIG_SYS_USB_OHCI_REGS_BASE	0x4C000000
+#define	CONFIG_SYS_USB_OHCI_SLOT_NAME	"tdex270"
+#define	CONFIG_USB_STORAGE
+#endif
+
+#endif	/* __CONFIG_H */

include/configs/vpac270.h

@@ -0,0 +1,323 @@
+/*
+ * Voipac PXA270 configuration file
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Board Configuration Options
+ */
+#define	CONFIG_PXA27X		1	/* Marvell PXA270 CPU */
+#define	CONFIG_VPAC270		1	/* Voipac PXA270 board */
+
+#undef	BOARD_LATE_INIT
+#undef	CONFIG_SKIP_RELOCATE_UBOOT
+#undef	CONFIG_USE_IRQ
+#undef	CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Environment settings
+ */
+#define	CONFIG_ENV_SIZE			0x4000
+#define	CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)
+#define	CONFIG_SYS_GBL_DATA_SIZE	128
+
+#define	CONFIG_ENV_OVERWRITE		/* override default environment */
+
+#define	CONFIG_BOOTCOMMAND						\
+	"if mmc init && fatload mmc 0 0xa4000000 uImage; then "		\
+		"bootm 0xa4000000; "					\
+	"fi; "								\
+	"if usb reset && fatload usb 0 0xa4000000 uImage; then "	\
+		"bootm 0xa4000000; "					\
+	"fi; "								\
+	"bootm 0x40000;"
+#define	CONFIG_BOOTARGS			"console=tty0 console=ttyS0,115200"
+#define	CONFIG_TIMESTAMP
+#define	CONFIG_BOOTDELAY		2	/* Autoboot delay */
+#define	CONFIG_CMDLINE_TAG
+#define	CONFIG_SETUP_MEMORY_TAGS
+
+#define	CONFIG_LZMA			/* LZMA compression support */
+
+/*
+ * Serial Console Configuration
+ */
+#define	CONFIG_PXA_SERIAL
+#define	CONFIG_FFUART			1
+#define	CONFIG_BAUDRATE			115200
+#define	CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+
+#define	CONFIG_CMD_NET
+#define	CONFIG_CMD_ENV
+#undef	CONFIG_CMD_IMLS
+#define	CONFIG_CMD_MMC
+#define	CONFIG_CMD_USB
+#undef	CONFIG_LCD
+#define	CONFIG_CMD_IDE
+
+#ifdef	CONFIG_ONENAND_U_BOOT
+#undef	CONFIG_CMD_FLASH
+#define	CONFIG_CMD_ONENAND
+#else
+#define	CONFIG_CMD_FLASH
+#undef	CONFIG_CMD_ONENAND
+#endif
+
+/*
+ * Networking Configuration
+ *  chip on the Voipac PXA270 board
+ */
+#ifdef	CONFIG_CMD_NET
+#define	CONFIG_CMD_PING
+#define	CONFIG_CMD_DHCP
+
+#define	CONFIG_NET_MULTI		1
+#define	CONFIG_DRIVER_DM9000		1
+#define CONFIG_DM9000_BASE		0x08000300	/* CS2 */
+#define DM9000_IO			(CONFIG_DM9000_BASE)
+#define DM9000_DATA			(CONFIG_DM9000_BASE + 4)
+#define	CONFIG_NET_RETRY_COUNT		10
+
+#define	CONFIG_BOOTP_BOOTFILESIZE
+#define	CONFIG_BOOTP_BOOTPATH
+#define	CONFIG_BOOTP_GATEWAY
+#define	CONFIG_BOOTP_HOSTNAME
+#endif
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef	CONFIG_CMD_MMC
+#define	CONFIG_MMC
+#define	CONFIG_PXA_MMC
+#define	CONFIG_SYS_MMC_BASE		0xF0000000
+#define	CONFIG_CMD_FAT
+#define	CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef	CONFIG_CMD_KGDB
+#define	CONFIG_KGDB_BAUDRATE		230400		/* speed to run kgdb serial port */
+#define	CONFIG_KGDB_SER_INDEX		2		/* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define	CONFIG_SYS_HUSH_PARSER		1
+#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+#define	CONFIG_SYS_LONGHELP				/* undef to save memory	*/
+#ifdef	CONFIG_SYS_HUSH_PARSER
+#define	CONFIG_SYS_PROMPT		"$ "		/* Monitor Command Prompt */
+#else
+#define	CONFIG_SYS_PROMPT		"=> "		/* Monitor Command Prompt */
+#endif
+#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size */
+#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
+#define	CONFIG_SYS_MAXARGS		16		/* max number of command args */
+#define	CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define	CONFIG_SYS_DEVICE_NULLDEV	1
+
+/*
+ * Clock Configuration
+ */
+#undef	CONFIG_SYS_CLKS_IN_HZ
+#define	CONFIG_SYS_HZ			3250000		/* Timer @ 3250000 Hz */
+#define CONFIG_SYS_CPUSPEED		0x190		/* standard setting for 312MHz; L=16, N=1.5, A=0, SDCLK!=SystemBus */
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define	CONFIG_STACKSIZE		(128*1024)	/* regular stack */
+#ifdef	CONFIG_USE_IRQ
+#define	CONFIG_STACKSIZE_IRQ		(4*1024)	/* IRQ stack */
+#define	CONFIG_STACKSIZE_FIQ		(4*1024)	/* FIQ stack */
+#endif
+
+/*
+ * DRAM Map
+ */
+#define	CONFIG_NR_DRAM_BANKS		2		/* We have 2 banks of DRAM */
+#define	PHYS_SDRAM_1			0xa0000000	/* SDRAM Bank #1 */
+#define	PHYS_SDRAM_1_SIZE		0x08000000	/* 128 MB */
+#define	PHYS_SDRAM_2			0x80000000	/* SDRAM Bank #2 */
+#define	PHYS_SDRAM_2_SIZE		0x08000000	/* 128 MB */
+
+#define	CONFIG_SYS_DRAM_BASE		0xa0000000	/* CS0 */
+#define	CONFIG_SYS_DRAM_SIZE		0x10000000	/* 256 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM */
+
+#define	CONFIG_SYS_LOAD_ADDR		(0x5c000000)
+
+/*
+ * NOR FLASH
+ */
+#if	defined(CONFIG_CMD_FLASH)	/* NOR */
+#define	PHYS_FLASH_1			0x00000000	/* Flash Bank #1 */
+#define	PHYS_FLASH_2			0x02000000	/* Flash Bank #2 */
+
+#define	CONFIG_SYS_FLASH_CFI
+#define	CONFIG_FLASH_CFI_DRIVER		1
+
+#define	CONFIG_SYS_MAX_FLASH_SECT	(4 + 255)
+#define	CONFIG_SYS_MAX_FLASH_BANKS	2
+#define	CONFIG_SYS_FLASH_BANKS_LIST	{ PHYS_FLASH_1, PHYS_FLASH_2 }
+
+#define	CONFIG_SYS_FLASH_ERASE_TOUT	(25*CONFIG_SYS_HZ)
+#define	CONFIG_SYS_FLASH_WRITE_TOUT	(25*CONFIG_SYS_HZ)
+
+#define	CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
+#define	CONFIG_SYS_FLASH_PROTECTION		1
+
+#define CONFIG_ENV_IS_IN_FLASH		1
+
+#elif	defined(CONFIG_CMD_ONENAND)	/* OneNAND */
+#define	CONFIG_SYS_NO_FLASH
+#define	CONFIG_SYS_ONENAND_BASE		0x00000000
+#define	CONFIG_ENV_IS_IN_ONENAND	1
+
+#else	/* No flash */
+#define	CONFIG_SYS_NO_FLASH
+#define	CONFIG_SYS_ENV_IS_NOWHERE
+#endif
+
+#define	CONFIG_SYS_MONITOR_BASE		0x000000
+#define	CONFIG_SYS_MONITOR_LEN		0x40000
+
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE	0x40000
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+/*
+ * IDE
+ */
+#ifdef	CONFIG_CMD_IDE
+#define	CONFIG_LBA48
+#undef	CONFIG_IDE_LED
+#undef	CONFIG_IDE_RESET
+
+#define CONFIG_SYS_IDE_MAXBUS		1
+#define CONFIG_SYS_IDE_MAXDEVICE	1
+
+#define CONFIG_SYS_ATA_BASE_ADDR	0x0c000000
+#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0
+
+#define CONFIG_SYS_ATA_DATA_OFFSET	0x120
+#define CONFIG_SYS_ATA_REG_OFFSET	0x120
+#define CONFIG_SYS_ATA_ALT_OFFSET	0x120
+
+#define	CONFIG_SYS_ATA_STRIDE		2
+#endif
+
+/*
+ * GPIO settings
+ */
+#define	CONFIG_SYS_GPSR0_VAL	0x01308800
+#define	CONFIG_SYS_GPSR1_VAL	0x00cf0000
+#define	CONFIG_SYS_GPSR2_VAL	0x922ac000
+#define	CONFIG_SYS_GPSR3_VAL	0x0161e800
+
+#define	CONFIG_SYS_GPCR0_VAL	0x00010000
+#define	CONFIG_SYS_GPCR1_VAL	0x0
+#define	CONFIG_SYS_GPCR2_VAL	0x0
+#define	CONFIG_SYS_GPCR3_VAL	0x0
+
+#define	CONFIG_SYS_GPDR0_VAL	0xcbb18800
+#define	CONFIG_SYS_GPDR1_VAL	0xfccfa981
+#define	CONFIG_SYS_GPDR2_VAL	0x922affff
+#define	CONFIG_SYS_GPDR3_VAL	0x0161e904
+
+#define	CONFIG_SYS_GAFR0_L_VAL	0x00100000
+#define	CONFIG_SYS_GAFR0_U_VAL	0xa5da8510
+#define	CONFIG_SYS_GAFR1_L_VAL	0x6992901a
+#define	CONFIG_SYS_GAFR1_U_VAL	0xaaa5a0aa
+#define	CONFIG_SYS_GAFR2_L_VAL	0xaaaaaaaa
+#define	CONFIG_SYS_GAFR2_U_VAL	0x4109a401
+#define	CONFIG_SYS_GAFR3_L_VAL	0x54010310
+#define	CONFIG_SYS_GAFR3_U_VAL	0x00025401
+
+#define	CONFIG_SYS_PSSR_VAL	0x30
+
+/*
+ * Clock settings
+ */
+#define	CONFIG_SYS_CKEN		0x00500240
+#define	CONFIG_SYS_CCCR		0x02000290
+
+/*
+ * Memory settings
+ */
+#define	CONFIG_SYS_MSC0_VAL	0x3ffc95fa
+#define	CONFIG_SYS_MSC1_VAL	0x02ccf974
+#define	CONFIG_SYS_MSC2_VAL	0x00000000
+#define	CONFIG_SYS_MDCNFG_VAL	0x8ad30ad3
+#define	CONFIG_SYS_MDREFR_VAL	0x201fe01e
+#define	CONFIG_SYS_MDMRS_VAL	0x00000000
+#define	CONFIG_SYS_FLYCNFG_VAL	0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL	0x40044004
+#define	CONFIG_SYS_MEM_BUF_IMP	0x0f
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define	CONFIG_SYS_MECR_VAL	0x00000001
+#define	CONFIG_SYS_MCMEM0_VAL	0x00014307
+#define	CONFIG_SYS_MCMEM1_VAL	0x00014307
+#define	CONFIG_SYS_MCATT0_VAL	0x0001c787
+#define	CONFIG_SYS_MCATT1_VAL	0x0001c787
+#define	CONFIG_SYS_MCIO0_VAL	0x0001430f
+#define	CONFIG_SYS_MCIO1_VAL	0x0001430f
+
+/*
+ * LCD
+ */
+#ifdef	CONFIG_LCD
+#define CONFIG_VOIPAC_LCD
+#endif
+
+/*
+ * USB
+ */
+#ifdef CONFIG_CMD_USB
+#define	CONFIG_USB_OHCI_NEW
+#define	CONFIG_SYS_USB_OHCI_CPU_INIT
+#define	CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define	CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
+#define	CONFIG_SYS_USB_OHCI_REGS_BASE	0x4C000000
+#define	CONFIG_SYS_USB_OHCI_SLOT_NAME	"vpac270"
+#define	CONFIG_USB_STORAGE
+#endif
+
+#endif	/* __CONFIG_H */

include/configs/zipitz2.h

@@ -0,0 +1,259 @@
+/*
+ * Aeronix Zipit Z2 configuration file
+ *
+ * Copyright (C) 2009-2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Board Configuration Options
+ */
+#define	CONFIG_PXA27X		1	/* Marvell PXA270 CPU */
+#define	CONFIG_ZIPITZ2		1	/* Zipit Z2 board */
+
+#undef	BOARD_LATE_INIT
+#undef	CONFIG_SKIP_RELOCATE_UBOOT
+#undef	CONFIG_USE_IRQ
+#undef	CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Environment settings
+ */
+#define	CONFIG_ENV_OVERWRITE
+#define CONFIG_ENV_IS_IN_FLASH		1
+#define CONFIG_ENV_ADDR			0x40000
+#define CONFIG_ENV_SIZE			0x20000
+
+#define	CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + CONFIG_STACKSIZE)
+#define	CONFIG_SYS_GBL_DATA_SIZE	512
+
+#define	CONFIG_BOOTCOMMAND						\
+	"if mmc init && fatload mmc 0 0xa0000000 uboot.script ; then "	\
+		"source 0xa0000000; "					\
+	"else "								\
+		"bootm 0x60000; "					\
+	"fi; "
+#define	CONFIG_BOOTARGS							\
+	"console=tty0 console=ttyS2,115200 fbcon=rotate:3"
+#define	CONFIG_TIMESTAMP
+#define	CONFIG_BOOTDELAY		2	/* Autoboot delay */
+#define	CONFIG_CMDLINE_TAG
+#define	CONFIG_SETUP_MEMORY_TAGS
+
+#define	CONFIG_LZMA			/* LZMA compression support */
+
+/*
+ * Serial Console Configuration
+ * STUART - the lower serial port on Colibri board
+ */
+#define	CONFIG_PXA_SERIAL
+#define	CONFIG_STUART			1
+#define	CONFIG_BAUDRATE			115200
+#define	CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+
+#undef	CONFIG_CMD_NET
+#define	CONFIG_CMD_ENV
+#undef	CONFIG_CMD_IMLS
+#define	CONFIG_CMD_MMC
+#define	CONFIG_CMD_SPI
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef	CONFIG_CMD_MMC
+#define	CONFIG_MMC
+#define	CONFIG_PXA_MMC
+#define	CONFIG_SYS_MMC_BASE		0xF0000000
+#define	CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define	CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * SPI and LCD
+ */
+#ifdef	CONFIG_CMD_SPI
+#define	CONFIG_SOFT_SPI
+#define	CONFIG_LCD
+#define	CONFIG_LMS283GF05
+#define	CONFIG_VIDEO_LOGO
+#define	CONFIG_CMD_BMP
+#define	CONFIG_SPLASH_SCREEN
+#define	CONFIG_SPLASH_SCREEN_ALIGN
+#define	CONFIG_VIDEO_BMP_GZIP
+#define	CONFIG_VIDEO_BMP_RLE8
+#define	CONFIG_SYS_VIDEO_LOGO_MAX_SIZE	(2 << 20)
+#undef	SPI_INIT
+
+#define	SPI_DELAY	udelay(10)
+#define	SPI_SDA(val)	zipitz2_spi_sda(val)
+#define	SPI_SCL(val)	zipitz2_spi_scl(val)
+#define	SPI_READ	zipitz2_spi_read()
+#ifndef	__ASSEMBLY__
+void zipitz2_spi_sda(int);
+void zipitz2_spi_scl(int);
+unsigned char zipitz2_spi_read(void);
+#endif
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef	CONFIG_CMD_KGDB
+#define	CONFIG_KGDB_BAUDRATE		230400		/* speed to run kgdb serial port */
+#define	CONFIG_KGDB_SER_INDEX		2		/* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define	CONFIG_SYS_HUSH_PARSER		1
+#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+#define	CONFIG_SYS_LONGHELP				/* undef to save memory	*/
+#ifdef	CONFIG_SYS_HUSH_PARSER
+#define	CONFIG_SYS_PROMPT		"$ "		/* Monitor Command Prompt */
+#else
+#define	CONFIG_SYS_PROMPT		"=> "		/* Monitor Command Prompt */
+#endif
+#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size */
+#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
+#define	CONFIG_SYS_MAXARGS		16		/* max number of command args */
+#define	CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define	CONFIG_SYS_DEVICE_NULLDEV	1
+
+/*
+ * Clock Configuration
+ */
+#undef	CONFIG_SYS_CLKS_IN_HZ
+#define	CONFIG_SYS_HZ			3250000		/* Timer @ 3250000 Hz */
+#define CONFIG_SYS_CPUSPEED		0x190		/* standard setting for 312MHz; L=16, N=1.5, A=0, SDCLK!=SystemBus */
+
+/*
+ * Stack sizes
+ */
+#define	CONFIG_STACKSIZE		(128*1024)	/* regular stack */
+#ifdef	CONFIG_USE_IRQ
+#define	CONFIG_STACKSIZE_IRQ		(4*1024)	/* IRQ stack */
+#define	CONFIG_STACKSIZE_FIQ		(4*1024)	/* FIQ stack */
+#endif
+
+/*
+ * DRAM Map
+ */
+#define	CONFIG_NR_DRAM_BANKS		1		/* We have 1 bank of DRAM */
+#define	PHYS_SDRAM_1			0xa0000000	/* SDRAM Bank #1 */
+#define	PHYS_SDRAM_1_SIZE		0x02000000	/* 32 MB */
+
+#define	CONFIG_SYS_DRAM_BASE		0xa0000000	/* CS0 */
+#define	CONFIG_SYS_DRAM_SIZE		0x02000000	/* 32 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM */
+
+#define	CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_DRAM_BASE
+
+/*
+ * NOR FLASH
+ */
+#define PHYS_FLASH_1			0x00000000	/* Flash Bank #1 */
+#define PHYS_FLASH_SIZE			0x00800000	/* 8 MB */
+#define PHYS_FLASH_SECT_SIZE		0x00010000	/* 64 KB sectors */
+#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER		1
+#define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
+
+#define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
+#define CONFIG_SYS_MONITOR_LEN		PHYS_FLASH_SECT_SIZE
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_MAX_FLASH_SECT	256
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	(2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT	(2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_LOCK_TOUT	(2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_UNLOCK_TOUT	(2*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_PROTECTION
+
+/*
+ * GPIO settings
+ */
+#define CONFIG_SYS_GAFR0_L_VAL	0x02000140
+#define CONFIG_SYS_GAFR0_U_VAL	0x59188000
+#define CONFIG_SYS_GAFR1_L_VAL	0x63900002
+#define CONFIG_SYS_GAFR1_U_VAL	0xaaa03950
+#define CONFIG_SYS_GAFR2_L_VAL	0x0aaaaaaa
+#define CONFIG_SYS_GAFR2_U_VAL	0x29000308
+#define CONFIG_SYS_GAFR3_L_VAL	0x54000000
+#define CONFIG_SYS_GAFR3_U_VAL	0x000000d5
+#define CONFIG_SYS_GPCR0_VAL	0x00000000
+#define CONFIG_SYS_GPCR1_VAL	0x00000020
+#define CONFIG_SYS_GPCR2_VAL	0x00000000
+#define CONFIG_SYS_GPCR3_VAL	0x00000000
+#define CONFIG_SYS_GPDR0_VAL	0xdafcee00
+#define CONFIG_SYS_GPDR1_VAL	0xffa3aaab
+#define CONFIG_SYS_GPDR2_VAL	0x8fe1ffff
+#define CONFIG_SYS_GPDR3_VAL	0x001b1f8a
+#define CONFIG_SYS_GPSR0_VAL	0x06080400
+#define CONFIG_SYS_GPSR1_VAL	0x007f0000
+#define CONFIG_SYS_GPSR2_VAL	0x032a0000
+#define CONFIG_SYS_GPSR3_VAL	0x00000180
+
+#define CONFIG_SYS_PSSR_VAL	0x30
+
+/*
+ * Clock settings
+ */
+#define CONFIG_SYS_CKEN		0x00511220
+#define CONFIG_SYS_CCCR		0x00000190
+
+/*
+ * Memory settings
+ */
+#define CONFIG_SYS_MSC0_VAL	0x2ffc38f8
+#define CONFIG_SYS_MSC1_VAL	0x0000ccd1
+#define CONFIG_SYS_MSC2_VAL	0x0000b884
+#define CONFIG_SYS_MDCNFG_VAL	0x08000ba9
+#define CONFIG_SYS_MDREFR_VAL	0x2011a01e
+#define CONFIG_SYS_MDMRS_VAL	0x00000000
+#define CONFIG_SYS_FLYCNFG_VAL	0x00010001
+#define CONFIG_SYS_SXCNFG_VAL	0x40044004
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CONFIG_SYS_MECR_VAL	0x00000001
+#define CONFIG_SYS_MCMEM0_VAL	0x00014307
+#define CONFIG_SYS_MCMEM1_VAL	0x00014307
+#define CONFIG_SYS_MCATT0_VAL	0x0001c787
+#define CONFIG_SYS_MCATT1_VAL	0x0001c787
+#define CONFIG_SYS_MCIO0_VAL	0x0001430f
+#define CONFIG_SYS_MCIO1_VAL	0x0001430f
+
+#endif	/* __CONFIG_H */

include/lcd.h

@@ -87,7 +87,7 @@ typedef struct vidinfo {
 	u_char	vl_wbf;		/* Wait between frames */
 } vidinfo_t;
 
-#elif defined CONFIG_PXA250
+#elif defined CONFIG_PXA250 || defined CONFIG_PXA27X || defined CONFIG_CPU_MONAHANS
 /*
  * PXA LCD DMA descriptor
  */

onenand_ipl/board/vpac270/Makefile

@@ -0,0 +1,83 @@
+IPL	=onenand_ipl
+include $(TOPDIR)/config.mk
+
+LDSCRIPT= $(TOPDIR)/onenand_ipl/board/$(BOARDDIR)/u-boot.onenand.lds
+LDFLAGS	= -Bstatic -T $(onenandobj)u-boot.lds -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS)
+AFLAGS	+= -DCONFIG_PRELOADER -DCONFIG_ONENAND_IPL
+CFLAGS	+= -DCONFIG_PRELOADER -DCONFIG_ONENAND_IPL
+OBJCFLAGS += --gap-fill=0x00
+
+SOBJS	:= lowlevel_init.o
+SOBJS	+= start.o
+COBJS	:= vpac270.o
+COBJS	+= onenand_read.o
+COBJS	+= onenand_boot.o
+
+SRCS	:= $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS	:= $(SOBJS) $(COBJS)
+LNDIR	:= $(OBJTREE)/onenand_ipl/board/$(BOARDDIR)
+
+onenandobj	:= $(OBJTREE)/onenand_ipl/
+
+ALL	= $(onenandobj)onenand-ipl $(onenandobj)onenand-ipl.bin $(onenandobj)onenand-ipl-2k.bin
+
+all:	$(obj).depend $(ALL)
+
+$(onenandobj)onenand-ipl-2k.bin:	$(onenandobj)onenand-ipl
+	$(OBJCOPY) ${OBJCFLAGS} --pad-to=0x5c040400 -O binary $< $@
+
+$(onenandobj)onenand-ipl.bin:	$(onenandobj)onenand-ipl
+	$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(onenandobj)onenand-ipl:	$(OBJS) $(onenandobj)u-boot.lds
+	cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+		-Map $@.map -o $@
+
+$(onenandobj)u-boot.lds:	$(LDSCRIPT)
+	$(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
+
+# create symbolic links from common files
+
+# from cpu directory
+$(obj)start.S:
+	@rm -f $@
+	ln -s $(SRCTREE)/$(CPUDIR)/start.S $@
+
+# from onenand_ipl directory
+$(obj)onenand_ipl.h:
+	@rm -f $@
+	ln -s $(SRCTREE)/onenand_ipl/onenand_ipl.h $@
+
+$(obj)onenand_boot.c:	$(obj)onenand_ipl.h
+	@rm -f $@
+	ln -s $(SRCTREE)/onenand_ipl/onenand_boot.c $@
+
+$(obj)onenand_read.c:	$(obj)onenand_ipl.h
+	@rm -f $@
+	ln -s $(SRCTREE)/onenand_ipl/onenand_read.c $@
+
+ifneq ($(OBJTREE), $(SRCTREE))
+$(obj)vpac270.c:
+	@rm -f $@
+	ln -s $(SRCTREE)/onenand_ipl/board/$(BOARDDIR)/vpac270.c $@
+
+$(obj)lowlevel_init.S:
+	@rm -f $@
+	ln -s $(SRCTREE)/onenand_ipl/board/$(BOARDDIR)/lowlevel_init.S $@
+endif
+
+#########################################################################
+
+$(obj)%.o:	$(obj)%.S
+	$(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o:	$(obj)$.c
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

onenand_ipl/board/vpac270/config.mk

@@ -0,0 +1 @@
+TEXT_BASE = 0x5c03fc00

onenand_ipl/board/vpac270/lowlevel_init.S

@@ -0,0 +1,34 @@
+/*
+ * Voipac PXA270 Lowlevel Hardware Initialization
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/macro.h>
+
+.globl lowlevel_init
+lowlevel_init:
+	pxa_clock_setup
+	mov	pc, lr

onenand_ipl/board/vpac270/u-boot.onenand.lds

@@ -0,0 +1,51 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+	  start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) . = ALIGN(4); }
+	_end = .;
+}

onenand_ipl/board/vpac270/vpac270.c

@@ -0,0 +1,42 @@
+/*
+ * (C) Copyright 2004
+ * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net
+ *
+ * (C) Copyright 2002
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+
+int board_init (void)
+{
+	return 0;
+}
+
+int s_init(int skip)
+{
+	return 0;
+}