CSF_PAD_SIZE should be defined in hab.h, move it to that location now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The size of the IVT header should be defined in hab.h move it there now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The current code disjoins an entire block of code on hab_entry pass/fail
resulting in a large chunk of authenticate_image being offset to the right.
Fix this by checking hab_entry() pass/failure and exiting the function
directly if in an error state.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
There is no need to call is_enabled() twice in authenticate_image - it does
nothing but add an additional layer of indentation.
We can check for is_enabled() at the start of the function and return the
result code directly.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
authenticate_image returns 1 for success and 0 for failure. That result
code is mapped directly to the result code for the command line function
hab_auth_img - which means when hab_auth_img succeeds it is returning
CMD_RET_FAILURE (1) instead of CMD_RET_SUCCESS (0).
This patch fixes this behaviour by making authenticate_image() return 0 for
success and 1 for failure. Both users of authenticate_image() as a result
have some minimal churn. The upshot is once done when hab_auth_img is
called from the command line we set $? in the standard way for scripting
functions to act on.
Fixes: 36c1ca4d46 ("imx: Support i.MX6 High Assurance Boot
authentication")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Both usages of authenticate_image treat the result code as a simple binary.
The command line usage of authenticate_image directly returns the result
code of authenticate_image as a success/failure code.
Right now when calling hab_auth_img and test the result code in a shell a
passing hab_auth_img will appear to the shell as a fail.
The first step in fixing this behaviour is to fix-up the result code return
by authenticate_image() itself, subsequent patches fix the interpretation
of authenticate_image so that zero will return CMD_RET_SUCCESS and non-zero
will return CMD_RET_FAILURE.
The first step is fixing the return type in authenticate_image() so do that
now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Like many other i.MX6 based boards, there are multiple variants of
the cm-fx6 module featuring different SoC variants. Furthermore, the
module can be paired with multiple baseboards.
At the same time modern distribution like Fedora require U-Boot to
select a proper devicetree which depends on the SoC variant and the
baseboard.
Thus, export the SoC variant and the actual board to the environment
following the conventions of other i.MX6 devices (e.g. the NXP boards)
such that the environment can select a devicetree file to load.
For now, we only know for sure that the cm-fx6 module and the SB-fx6m
baseboard amount to a Utilite Computer variant (depending on the SoC).
Further combinations may be added in the future; e.g. CompuLab's
evaluation board once someone can verify the identification string
stored in its eeprom.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The "clocks" and "bootaux" commands are only usable in full U-Boot, not
SPL, so do not link them inside of SPL. Rework a little of the bootaux
related code to make use of __weak and declare parts of it static as
it's local to the file.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
i.MX6ULL also does not have a MMDC_P1_BASE_ADDR, so do not try to
access it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <ssbabic@denx.de>
The i.MX 6UL/ULL feature a Cortex-A7 CPU which suppor the ARM
generic timer. This change makes use of the ARM generic timer in
U-Boot.
This is crucial to make the ARM generic timers usable in Linux since
timer_init() initalizes the system counter module, which is necessary
to use the generic timers CP15 registers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Introduce a new config symbol to select the i.MX
General Purpose Timer (GPT).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Since commit 051ba9e082 ("Kconfig: mx6ull: Deselect MX6UL from
CONFIG_MX6ULL") CONFIG_MX6ULL does not select CONFIG_MX6UL anymore, so
take this into consideration in all the checks for CONFIG_MX6UL.
This fixes a boot regression.
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
commit 20f1471416 ("imx: spl: Update NAND bootmode detection bit")
broke the NAND bootmode detection by checking if
BOOT_CFG1[7:4] == 0x8 for NAND boot mode.
This commit essentially reverts it, while using the IMX6_BMODE_*
macros that were introduced since.
Tables 8-7 & 8-10 from IMX6DQRM say the NAND boot mode selection
is done when BOOT_CFG1[7] is 1, but BOOT_CFG1[6:4] is not
necessarily 0x0 in this case.
Actually, NAND boot mode is when 0x8 <= BOOT_CFG1[7:4] <= 0xf,
like it was in the code before.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tim Harvey <tharvey@gateworks.com>
This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.
It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.
When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.
In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.
https://community.nxp.com/docs/DOC-105652
File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently CONFIG_SECURE_BOOT is selecting FSL_CAAM for all i.MX devices,
this causes the following error when building mx6sl boards since
this SoC doesn't have the CAAM block:
In file included from drivers/crypto/fsl/jobdesc.c:12:0:
drivers/crypto/fsl/jobdesc.c: In function 'inline_cnstr_jobdesc_blob_dek':
include/fsl_sec.h:268:25: error: 'CAAM_ARB_BASE_ADDR' undeclared (first use
in this function)
#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
^
include/fsl_sec.h:268:25: note: each undeclared identifier is reported only
once for each function it appears in
#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
^
scripts/Makefile.build:280: recipe for target 'drivers/crypto/fsl/jobdesc.o'
failed
make[3]: *** [drivers/crypto/fsl/jobdesc.o] Error 1
scripts/Makefile.build:425: recipe for target 'drivers/crypto/fsl' failed
make[2]: *** [drivers/crypto/fsl] Error 2
scripts/Makefile.build:425: recipe for target 'drivers/crypto' failed
make[1]: *** [drivers/crypto] Error 2
Add HAS_CAAM configuration to avoid this error.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
MX6UL contains features that MX6ULL doesn't support.
Deselect CONFIG_MX6UL and select SYS_L2CACHE_OFF and ROM_UNIFIED_SECTIONS.
The motivation for doing this change is that MX6UL supports CAAM and
MX6ULL does not.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently the MX6SL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the
correct dtb is imx6sx-sdb-reva.dtb, so make this possible.
While at it, remove an extra 'mmc dev'.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.
Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add new board names for existing board support
imx6q - icore and icore_rqs boards
imx6ul - geam6ul and isiot boards
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.
It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.
While at it, rename it to imx_wdog_disable_powerdown().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Clear powerdown enable bit for WDOG3 on i.MX6ULL to avoid unwanted
kernel reboots.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Currently the MX6QDL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Create board support for GE PPD, based on mx53loco.
Use mx53ppd_defconfig make target to configure for this board.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
When a high speed card is connected to mx51evk the following error is seen:
U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)
CPU: Freescale i.MX51 rev3.0 at 800 MHz
Reset cause: POR
Board: MX51EVK
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX51 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
The i.MX51 ts4800 board already selects this option, but it is better
to move this selection to the i.MX51 SoC level instead.
Successfully tested with a high speed SD card on a mx51evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
When a high speed card is connected to mx25 the following error is seen:
U-Boot 2017.11-rc2-00104-gb79372a (Oct 31 2017 - 11:02:22 -0200)
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR
Board: MX25PDK
I2C: ready
DRAM: 64 MiB
No arch specific invalidate_icache_all available!
MMC: FSL_SDHC: 0
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
, which prevents any usage of the SD card.
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX25 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
Successfully tested with a high speed SD card on a mx25pdk board.
Suggested-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Otavio Salvador <otavio@ossystems.com.br> # mx25pdk
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Add support for the DHCOM i.MX6 PDK board. This board has:
- FEC ethernet
- EHCI USB host
- 3x SDMMC
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The configuration files imximage.cfg are used for the DDR controller
configuration.
Add DDR configuration function to replace the DDR controller
configuration in the imximage.cfg file. The function can be used for
DDR size detection.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
When compiling with W=1 the following warning is observed:
arch/arm/mach-imx/mx6/soc.c:213:12: warning: no previous prototype for ‘get_board_rev’ [-Wmissing-prototypes] u32 __weak get_board_rev(void)
Fix the build warning by including <asm/bootm.h>.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.
Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Instead of having every board file to add its own g_dnl_bind_fixup()
implementation, move it to the common imx6 SPL code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Update these macros to use all upper-case to avoid checkpatch
warnings:
ENET_25MHz,
ENET_50MHz,
ENET_125MHz,
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The current mechanism using SCR/GPR registers work well when
the serial downloader boot mode has been selected explicitly
(either via boot mode pins or using bmode command). However,
in case the system entered boot ROM due to unbootable primary
boot devices (e.g. empty eMMC), the SPL fails to detect that
it has been downloaded through serial loader and tries to
continue booting from eMMC:
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The only known way to reliably detect USB serial downloader
is by checking the USB PHY receiver block power state...
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Memory dt node update introduced by spl_fixup_fdt() in below
commit was making DDR configuration in-appropriate
to boot falcon mode. Hence added dram_init_banksize for
explicit assignment of proper base and size of DDR.
"boot: fdt: Perform arch_fixup_fdt() on the given device tree for falcon boot"
(sha1: 6e7585bb64)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The NXP i.MX 6UL and 6ULL do not support SATA and have no SATA
boot mode, hence remove it from the boot device detecion. This
fixes a build error introduced with 3bd1642d4d ("imx: fix USB
boot mode detection for i.MX 6UL and 6ULL")
Fixes: 3bd1642d4d ("imx: fix USB boot mode detection for i.MX 6UL and 6ULL")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The soc_boot_modes array is only used by bmode command
and not needed in SPL. Don't include it into SPL.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
There is no need to clear the control register 100 times in a
loop, a single zero write clears the register. I didn't find any
justification why clearing this register in a loop is needed
(no info in i.MX6 errata or GPT timer linux driver, linux driver
uses single write to clear this control register).
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Bryan O'Donoghue
Christopher Spinrath
Tom Rini
Eran Matityahu
Fabio Estevam
Stefano Babic
Stefan Agner
Eric Nelson
Breno Lima
Jagan Teki
Peter Senna Tschudin
Lukasz Majewski
Marek Vasut
Ilya Ledvich
Uri Mashiach
Diego Dorta
Anatolij Gustschin
Maxime Ripard
Chris Packham
Jagan Teki